Viscoelastic and conductive characteristics of titanium carbide/polyethylene composites in relation to their structural parameters

2004 ◽  
Vol 91 (5) ◽  
pp. 3134-3139
Author(s):  
Mitsuhiro Kataoka ◽  
Toru Masuko
Keyword(s):  
Titanium Carbide ◽  
Structural Parameters ◽  
Polyethylene Composites

Effect of geometrical structural parameters on the strength properties of hard alloys based on titanium carbide

1996 ◽  
Vol 34 (3-4) ◽  
pp. 186-188 ◽  
Author(s):  
M. S. Koval'chenko ◽  
A. V. Laptev ◽  
V. V. Sverdel ◽  
N. A. Yurchuk
Keyword(s):  
Titanium Carbide ◽  
Structural Parameters ◽  
Strength Properties ◽  
Hard Alloys

Optimal design of a high homogeneous and small-size shim coil for atomic spin gyroscope based on 0-1 linear programming

2020 ◽  
Vol 64 (1-4) ◽  
pp. 165-172
Author(s):  
Dongge Deng ◽  
Mingzhi Zhu ◽  
Qiang Shu ◽  
Baoxu Wang ◽  
Fei Yang
Keyword(s):  
Linear Programming ◽  
Power Consumption ◽  
Low Power ◽  
Optimization Design ◽  
Structural Parameters ◽  
Axial Position ◽  
Low Power Consumption ◽  
Optimal Method ◽  
Atomic Spin ◽  
Shim Coil

It is necessary to develop a high homogeneous, low power consumption, high frequency and small-size shim coil for high precision and low-cost atomic spin gyroscope (ASG). To provide the shim coil, a multi-objective optimization design method is proposed. All structural parameters including the wire diameter are optimized. In addition to the homogeneity, the size of optimized coil, especially the axial position and winding number, is restricted to develop the small-size shim coil with low power consumption. The 0-1 linear programming is adopted in the optimal model to conveniently describe winding distributions. The branch and bound algorithm is used to solve this model. Theoretical optimization results show that the homogeneity of the optimized shim coil is several orders of magnitudes better than the same-size solenoid. A simulation experiment is also conducted. Experimental results show that optimization results are verified, and power consumption of the optimized coil is about half of the solenoid when providing the same uniform magnetic field. This indicates that the proposed optimal method is feasible to develop shim coil for ASG.

ABOUT HEAT CAPACITY OF TITANIUM CARBIDE TiCx

2019 ◽  
pp. 56-66
Author(s):  
I. Khidirov ◽  
V. V. Getmanskiy ◽  
A. S. Parpiev ◽  
Sh. A. Makhmudov
Keyword(s):  
Heat Capacity ◽  
High Temperature ◽  
Titanium Carbide ◽  
Temperature Dependence ◽  
Carbon Concentration ◽  
Room Temperature ◽  
Thermodynamic Characteristics ◽  
Liquid Nitrogen Temperature ◽  
Analysis Data ◽  
Thermal Excitation

This work relates to the field of thermophysical parameters of refractory interstitial alloys. The isochoric heat capacity of cubic titanium carbide TiCx has been calculated within the Debye approximation in the carbon concentration  range x = 0.70–0.97 at room temperature (300 K) and at liquid nitrogen temperature (80 K) through the Debye temperature established on the basis of neutron diffraction analysis data. It has been found out that at room temperature with decrease of carbon concentration the heat capacity significantly increases from 29.40 J/mol·K to 34.20 J/mol·K, and at T = 80 K – from 3.08 J/mol·K to 8.20 J/mol·K. The work analyzes the literature data and gives the results of the evaluation of the high-temperature dependence of the heat capacity СV of the cubic titanium carbide TiC0.97 based on the data of neutron structural analysis. It has been proposed to amend in the Neumann–Kopp formula to describe the high-temperature dependence of the titanium carbide heat capacity. After the amendment, the Neumann–Kopp formula describes the results of well-known experiments on the high-temperature dependence of the heat capacity of the titanium carbide TiCx. The proposed formula takes into account the degree of thermal excitation (a quantized number) that increases in steps with increasing temperature.The results allow us to predict the thermodynamic characteristics of titanium carbide in the temperature range of 300–3000 K and can be useful for materials scientists.

A Possible Basis for Nondestructive Characterization of Ropes of Nylon 6

1997 ◽  
Vol 503 ◽  
Author(s):  
H. Jiang ◽  
M. K. Davis ◽  
R. K. Eby ◽  
P. Arsenovic
Keyword(s):  
Tensile Strength ◽  
Service Life ◽  
Fiber Diameter ◽  
Structural Parameters ◽  
Crystal Form ◽  
Nylon 6 ◽  
Remaining Service Life ◽  
Nondestructive Characterization ◽  
Fractional Content

ABSTRACTPhysical properties and structural parameters have been measured for ropes of nylon 6 as a function of the number of use operations. The fractional content of the α crystal form, sound velocity, birefringence, tensile strength and length all increase systematically and significantly with increasing the number of use operations. The fractional content of the γ crystal form and fiber diameter decrease with use. These trends indicate that the measurement of such properties and structural parameters, especially the length, provide a possible basis for establishing a reliable, rapid, and convenient nondestructive characterization method to predict the remaining service life of nylon 6 ropes.

Structural Parameters of Bacterial Plankton in Ponds with High Contents of Mineral Nitrogen

2007 ◽  
Vol 43 (5) ◽  
pp. 91-100
Author(s):  
Ye. V. Starosila ◽  
G. N. Oleynik ◽  
Yu. G. Krot
Keyword(s):  
Structural Parameters ◽  
Mineral Nitrogen
Sign in / Sign up

Export Citation Format

Share Document