Rheology of HTPB propellant. I. Effect of solid loading, oxidizer particle size, and aluminum content

1992 ◽  
Vol 44 (11) ◽  
pp. 2043-2052 ◽  
Author(s):  
Rm. Muthiah ◽  
V. N. Krishnamurthy ◽  
B. R. Gupta
Author(s):  
Bashir Khoda ◽  
AMM Nazmul Ahsan ◽  
SM Abu Shovon

Abstract Solid transfer technology from mixtures is gaining ever-increasing attention from materials scientists and production engineers due to their high potential in near net-shaped production of cost-effective engineering components. Dip coating, a wet deposition method, is an effective and straightforward way of thin-film/layers formation. The dipping mixtures are often embedded with inorganic fillers, nanoparticles, or clusters (d<30 nm) that produce a thin film ranging from nm to couple microns. An increase in the volume of solid transfer by the dipping process can open-up a novel 3D near-net-shape production. However, adding larger inorganic particle size (>1µm) or adding a higher solid fraction will increase the solid transfer but may result in a multi-phase heterogeneous mixture. In this work, the physical mechanism of an increased volume of solid transfer with a larger spherical particle size (>5 µm) is investigated. Polymer-based glue and evaporating solvent are mixed to construct the liquid carrier system (LCS). Moderate volume fraction of inorganic particles (20% < ?p < 50%) are added into the LCS solution as solid loading. Three levels of binder volume fraction are considered to investigate the effect of the solid transfer. Cylindrical AISI 304 steel wire with dia 0.81 mm is dipped and the coating thickness, weight, and the surface packing coverage by the particles are measured in our lab. The results presented the influence of volume fraction of inorganic particle and glue composition on the solid transfer from the heterogeneous mixture.


2007 ◽  
Vol 27 (8-9) ◽  
pp. 1345-1351 ◽  
Author(s):  
K.S. Rajan ◽  
S.N. Srivastava ◽  
B. Pitchumani ◽  
B. Mohanty

2018 ◽  
Vol 747 ◽  
pp. 211-216 ◽  
Author(s):  
Yong-In Kim ◽  
Wonsik Lee ◽  
Jin Man Jang ◽  
Sang Wook Ui ◽  
Gye Seok An ◽  
...  

2019 ◽  
Vol 79 (4) ◽  
pp. 771-778 ◽  
Author(s):  
Junho Lee ◽  
Myungjin Lee

Abstract This study has been carried out to evaluate the applicability of the pilot scale hybrid type of stormwater runoff treatment system for treatment of combined sewer overflow. Also, to determine the optimum operation parameter such as coagulation dosage concentration, effectiveness of coagulant usage, surface loading rate and backwashing conditions. The pilot scale stormwater filtration system (SFS) was installed at the municipal wastewater plant serving the city of Cheongju (CWTP), Korea. CWTP has a capacity of 280,000 m3/day. The SFS consists of a hydrocyclone coagulation/flocculation with polyaluminium chloride silicate (PACS) and an upflow filter to treat combined sewer overflows. There are two modes (without PACS use and with PACS use) of operation for the SFS. In case of no coagulant use, the range of suspended solids (SS) and turbidity removal efficiency were 72.0–86.6% (mean 80.0%) and 30.9–71.1% (mean 49.3%), respectively. And, the recovery rate of filter was 79.2–83.6% (mean 81.2%); the rate of remaining solid loading in filter media was 16.4–20.8% (mean 18.8%) after backwashing. The influent turbidity, SS concentrations were 59.0–90.7 NTU (mean 72.0 NTU), 194.0–320.0mg/L (mean 246.7mg/L), respectively. The range of PACS dosage concentration was 6.0–7.1mg/L (mean 6.7mg/L). The range of SS and turbidity removal efficiency was 84.9–98.2 (mean 91.4%) and 70.7–96.3 (mean 84.0%), respectively. It was found that removal efficiency was enhanced with PACS dosage. The recovery rate of filter was 92.0–92.5% (mean 92.3%) the rate of remaining solid loading in filter media was 6.1–8.2% (mean 7.2%) after backwashing. In the case of coagulant use, the particle size of the effluent is bigger than influent particle size. The results showed that SFS with PACS use more effective than without PACS use in SS and turbidity removal efficiency and recovery rate of filter.


1969 ◽  
Vol 5 (4) ◽  
pp. 395-397
Author(s):  
S. S. Novikov ◽  
P. F. Pokhil ◽  
O. P. Rysakova-Romashkan

2010 ◽  
Vol 434-435 ◽  
pp. 88-91
Author(s):  
Yuan Li ◽  
Ji Qiang Gao ◽  
Jian Feng Yang

Two domestic silicon carbide powders with different particle size distribution and one petroleum coke powder were blended in proportion and then dispersed in aqueous medium. Green bodies were solidified from these suspensions via conventional slip casting. The effects of pH, solid loading, and the amount of dispersant on the formability and packing ability were evaluated. The results showed that the pH within 9.5-10.5, solid loading of 42vol%, aging time more than 24h, and 0.3wt% of dispersant were optimal. Complicated green bodies with height of 300mm and thickness of 3.5mm were obtained. The corresponding suspension viscosity was 1200mPa∙s and the relative packing density was 64.8%. The density is 3.01g∙cm-3 and the flexural strength is 305±15 MPa after reaction sintering. These results may be attributed to accurately using of dispersant and in-depth study of processing parameter.


Sign in / Sign up

Export Citation Format

Share Document