Injectable and moldable hydrogels for use in sensitive and wide range strain sensing applications

Biopolymers ◽  
2020 ◽  
Vol 111 (6) ◽  
Author(s):  
Zhen Qiao ◽  
Matthew Mieles ◽  
Hai‐Feng Ji
Keyword(s):  
Strain Sensing ◽  
Sensing Applications ◽  
Wide Range

scholarly journals Strain Sensor via Wood Anomalies in 2D Dielectric Array

Nanomaterials ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 1022
Author(s):  
Rashid G. Bikbaev ◽  
Ivan V. Timofeev ◽  
Vasiliy F. Shabanov
Keyword(s):  
Higher Plants ◽  
Numerical Study ◽  
Reciprocal Lattice ◽  
Strain Sensing ◽  
Photonic Materials ◽  
Sensing Applications ◽  
Wide Range ◽  
Sensor Structure ◽  
Optical Behavior ◽  
Chlorophyll Absorption

Optical sensing is one of many promising applications for all-dielectric photonic materials. Herein, we present an analytical and numerical study on the strain-responsive spectral properties of a bioinspired sensor. The sensor structure contains a two-dimensional periodic array of dielectric nanodisks to mimic the optical behavior of grana lamellae inside chloroplasts. To accumulate a noticeable response, we exploit the collective optical mode in grana ensemble. In higher plants, such a mode appears as Wood’s anomaly near the chlorophyll absorption line to control the photosynthesis rate. The resonance is shown persistent against moderate biological disorder and deformation. Under the stretching or compression of a symmetric structure, the mode splits into a couple of polarized modes. The frequency difference is accurately detected. It depends on the stretch coefficient almost linearly providing easy calibration of the strain-sensing device. The sensitivity of the considered structure remains at 5 nm/% in a wide range of strain. The influence of the stretching coefficient on the length of the reciprocal lattice vectors, as well as on the angle between them, is taken into account. This adaptive phenomenon is suggested for sensing applications in biomimetic optical nanomaterials.

Optimization of 3D Printed Elastomeric Nanocomposites for Flexible Strain Sensing Applications

2019 ◽  
Author(s):  
Mohammad Abshirini ◽  
Mohammad Charara ◽  
Mrinal C. Saha ◽  
M. Cengiz Altan ◽  
Yingtao Liu
Keyword(s):  
3D Printing ◽  
Strain Sensor ◽  
Sensitive Strain ◽  
Curing Temperature ◽  
Gauge Factor ◽  
Strain Sensing ◽  
Sensing Applications ◽  
Wide Range ◽  
Load Rate ◽  
3D Printed

Abstract Flexible and sensitive strain sensors can be utilized as wearable sensors and electronic devices in a wide range of applications, such as personal health monitoring, sports performance, and electronic skin. This paper presents the fabrication of a highly flexible and sensitive strain sensor by 3D printing an electrically conductive polydimethylsiloxane (PDMS)/multi-wall carbon nanotube (MWNT) nanocomposite on a PDMS substrate. To maximize the sensor’s gauge factor, the effects of MWNT concentration on the strain sensing function in nanocomposites are evaluated. Critical 3D printing and curing parameters, such as 3D printing nozzle diameter and nanocomposites curing temperature, are explored to achieve the highest piezoresistive response, showing that utilizing a smaller deposition nozzle size and higher curing temperature can result in a higher gauge factor. The optimized 3D printed nanocomposite sensor’s sensitivity is characterized under cyclic tensile loads at different maximum strains and loading rates. A linear piezoresistive response is observed up to 70% strain with an average gauge factor of 12, pointing to the sensor’s potential as a flexible strain sensor. In addition, the sensing function is almost independent of the applied load rate. The fabricated sensors are attached to a glove and used as a wearable sensor by detecting human finger and wrist motion. The results indicate that this 3D printed functional nanocomposite shows promise in a broad range of applications, including wearable and skin mounted sensors.

scholarly journals Multi-Walled Carbon Nanotubes-Based Sensors for Strain Sensing Applications

Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1261 ◽  
Author(s):  
Anindya Nag ◽  
Md. Eshrat E Alahi ◽  
Subhas Chandra Mukhopadhyay ◽  
Zhi Liu
Keyword(s):  
Structural Changes ◽  
Mechanical And Thermal Properties ◽  
Strain Sensing ◽  
Sensing Applications ◽  
Multi Walled Carbon Nanotube ◽  
Wide Range ◽  
Multi Walled Carbon Nanotubes ◽  
Conductive Nanomaterials ◽  
Walled Carbon Nanotubes

The use of multi-walled carbon nanotube (MWCNT)-based sensors for strain–strain applications is showcased in this paper. Extensive use of MWCNTs has been done for the fabrication and implementation of flexible sensors due to their enhanced electrical, mechanical, and thermal properties. These nanotubes have been deployed both in pure and composite forms for obtaining highly efficient sensors in terms of sensitivity, robustness, and longevity. Among the wide range of applications that MWCNTs have been exploited for, strain-sensing has been one of the most popular ones due to the high mechanical flexibility of these carbon allotropes. The MWCNT-based sensors have been able to deduce a broad spectrum of macro- and micro-scaled tensions through structural changes. This paper highlights some of the well-approved conjugations of MWCNTs with different kinds of polymers and other conductive nanomaterials to form the electrodes of the strain sensors. It also underlines some of the measures that can be taken in the future to improve the quality of these MWCNT-based sensors for strain-related applications.

scholarly journals Femtosecond Laser Fabrication of Hybrid Metal-Dielectric Structures with Nonlinear Photoluminescence

Photonics ◽  
2021 ◽  
Vol 8 (4) ◽  
pp. 121
Author(s):  
Ekaterina Ponkratova ◽  
Eduard Ageev ◽  
Filipp Komissarenko ◽  
Sergei Koromyslov ◽  
Dmitry Kudryashov ◽  
...  
Keyword(s):  
Visible Spectral Region ◽  
Single Step ◽  
Hybrid Nanostructures ◽  
Nonlinear Properties ◽  
Nanophotonic Devices ◽  
Sensing Applications ◽  
Structure Morphology ◽  
Wide Range ◽  
Nonlinear Signal ◽  
Dielectric Structures

Fabrication of hybrid micro- and nanostructures with a strong nonlinear response is challenging and represents a great interest due to a wide range of photonic applications. Usually, such structures are produced by quite complicated and time-consuming techniques. This work demonstrates laser-induced hybrid metal-dielectric structures with strong nonlinear properties obtained by a single-step fabrication process. We determine the influence of several incident femtosecond pulses on the Au/Si bi-layer film on produced structure morphology. The created hybrid systems represent isolated nanoparticles with a height of 250–500 nm exceeding the total thickness of the Au-Si bi-layer. It is shown that fabricated hybrid nanostructures demonstrate enhancement of the SHG signal (up to two orders of magnitude) compared to the initial planar sample and a broadband photoluminescence signal (more than 200 nm in width) in the visible spectral region. We establish the correlation between nonlinear signal and phase composition provided by Raman scattering measurements. Such laser-induced structures have significant potential in optical sensing applications and can be used as components for different nanophotonic devices.

scholarly journals A Nanoplasmonic-Based Biosensing Approach for Wide-Range and Highly Sensitive Detection of Chemicals

Nanomaterials ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1961
Author(s):  
Francesco Arcadio ◽  
Luigi Zeni ◽  
Aldo Minardo ◽  
Caterina Eramo ◽  
Stefania Di Di Ronza ◽  
...  
Keyword(s):  
Optical Fibers ◽  
Limit Of Detection ◽  
Slab Waveguide ◽  
Grating Pattern ◽  
Transparent Substrate ◽  
Synthetic Receptor ◽  
Sensing Applications ◽  
Wide Range ◽  
Plastic Optical Fibers ◽  
Highly Sensitive Detection

In a specific biosensing application, a nanoplasmonic sensor chip has been tested by an experimental setup based on an aluminum holder and two plastic optical fibers used to illuminate and collect the transmitted light. The studied plasmonic probe is based on gold nanograting, realized on the top of a Poly(methyl methacrylate) (PMMA) chip. The PMMA substrate could be considered as a transparent substrate and, in such a way, it has been already used in previous work. Alternatively, here it is regarded as a slab waveguide. In particular, we have deposited upon the slab surface, covered with a nanograting, a synthetic receptor specific for bovine serum albumin (BSA), to test the proposed biosensing approach. Exploiting this different experimental configuration, we have determined how the orientation of the nanostripes forming the grating pattern, with respect to the direction of the input light (longitudinal or orthogonal), influences the biosensing performances. For example, the best limit of detection (LOD) in the BSA detection that has been obtained is equal to 23 pM. Specifically, the longitudinal configuration is characterized by two observable plasmonic phenomena, each sensitive to a different BSA concentration range, ranging from pM to µM. This aspect plays a key role in several biochemical sensing applications, where a wide working range is required.

scholarly journals Wide range and highly linear signal processed systematic humidity sensor array using Methylene Blue and Graphene composite

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Muhammad Umair Khan ◽  
Gul Hassan ◽  
Rayyan Ali Shaukat ◽  
Qazi Muhammad Saqib ◽  
Mahesh Y. Chougale ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Linear Combination ◽  
Linear Function ◽  
Humidity Sensor ◽  
Sensor Array ◽  
Combination Method ◽  
Humidity Sensing ◽  
Sensing Applications ◽  
Wide Range ◽  
Graphene Flakes

AbstractThis paper proposes a signal processed systematic 3 × 3 humidity sensor array with all range and highly linear humidity response based on different particles size composite inks and different interspaces of interdigital electrodes (IDEs). The fabricated sensors are patterned through a commercial inkjet printer and the composite of Methylene Blue and Graphene with three different particle sizes of bulk Graphene Flakes (BGF), Graphene Flakes (GF), and Graphene Quantum Dots (GQD), which are employed as an active layer using spin coating technique on three types of IDEs with different interspaces of 300, 200, and 100 µm. All range linear function (0–100% RH) is achieved by applying the linear combination method of nine sensors in the signal processing field, where weights for linear combination are required, which are estimated by the least square solution. The humidity sensing array shows a fast response time (Tres) of 0.2 s and recovery time (Trec) of 0.4 s. From the results, the proposed humidity sensor array opens a new gateway for a wide range of humidity sensing applications with a linear function.

Piezotransistor-embedded microcantilever platform for strain sensing applications

2010 ◽  
Author(s):  
Pushpapraj Singh ◽  
Jianmin Miao
Keyword(s):  
Strain Sensing ◽  
Sensing Applications

scholarly journals A Review: Carbon Nanotube-Based Piezoresistive Strain Sensors

2012 ◽  
Vol 2012 ◽  
pp. 1-15 ◽  
Author(s):  
Waris Obitayo ◽  
Tao Liu
Keyword(s):  
Carbon Nanotubes ◽  
Carbon Nanotube ◽  
Composite Films ◽  
Strain Sensors ◽  
Voltage Response ◽  
Strain Sensing ◽  
Multiwalled Carbon ◽  
Sensing Applications ◽  
Mechanical Deformations ◽  
Electrical Resistivities

The use of carbon nanotubes for piezoresistive strain sensors has acquired significant attention due to its unique electromechanical properties. In this comprehensive review paper, we discussed some important aspects of carbon nanotubes for strain sensing at both the nanoscale and macroscale. Carbon nanotubes undergo changes in their band structures when subjected to mechanical deformations. This phenomenon makes them applicable for strain sensing applications. This paper signifies the type of carbon nanotubes best suitable for piezoresistive strain sensors. The electrical resistivities of carbon nanotube thin film increase linearly with strain, making it an ideal material for a piezoresistive strain sensor. Carbon nanotube composite films, which are usually fabricated by mixing small amounts of single-walled or multiwalled carbon nanotubes with selected polymers, have shown promising characteristics of piezoresistive strain sensors. Studies also show that carbon nanotubes display a stable and predictable voltage response as a function of temperature.

Sign in / Sign up

Export Citation Format

Share Document