scholarly journals Plastic adjustments of biparental care behavior across embryonic development under elevated temperature in a marine ectotherm

2021 ◽  
Author(s):  
Davide Spatafora ◽  
Gloria Massamba N'Siala ◽  
Federico Quattrocchi ◽  
Marco Milazzo ◽  
Piero Calosi
2019 ◽  
Vol 116 (13) ◽  
pp. 6238-6243 ◽  
Author(s):  
Michael Mikát ◽  
Lukáš Janošík ◽  
Kateřina Černá ◽  
Eva Matoušková ◽  
Jiří Hadrava ◽  
...  

Parental care behavior evolves to increase the survival of offspring. When offspring care becomes complicated for ecological reasons, cooperation of multiple individuals can be beneficial. There are two types of cooperative care: biparental care and worker (helper)-based care (e.g., eusociality). Although biparental care is common in several groups of vertebrates, it is generally rare in arthropods. Conversely, eusociality is widespread in insects, especially the aculeate Hymenoptera. Here, we present a case of biparental care in bees, inCeratina nigrolabiata(Apidae, Xylocopinae). Similar to eusocial behavior, biparental care leads to greater brood protection in this species. Male guarding increases provisioning of nests because females are liberated from the tradeoff between provisioning and nest protection. The main benefit of parental care for males should be increased paternity. Interestingly though, we found that paternity of offspring by guard males is extraordinarily low (10% of offspring). Generally, we found that nests were not guarded by the same male for the whole provisioning season, meaning that males arrive to nests as stepfathers. However, we show that long-term guarding performed by a single male does increase paternity. We suggest that the multiple-mating strategy of these bees increased the amount of time for interactions between the sexes, and this longer period of potential interaction supported the origin of biparental care. Eusociality based on monandry was thought to be the main type of extended brood protection in bees. We show that biparental care based on polyandry provides an interesting evolutionary alternative.


Author(s):  
G.J.C. Carpenter

In zirconium-hydrogen alloys, rapid cooling from an elevated temperature causes precipitation of the face-centred tetragonal (fct) phase, γZrH, in the form of needles, parallel to the close-packed <1120>zr directions (1). With low hydrogen concentrations, the hydride solvus is sufficiently low that zirconium atom diffusion cannot occur. For example, with 6 μg/g hydrogen, the solvus temperature is approximately 370 K (2), at which only the hydrogen diffuses readily. Shears are therefore necessary to produce the crystallographic transformation from hexagonal close-packed (hep) zirconium to fct hydride.The simplest mechanism for the transformation is the passage of Shockley partial dislocations having Burgers vectors (b) of the type 1/3<0110> on every second (0001)Zr plane. If the partial dislocations are in the form of loops with the same b, the crosssection of a hydride precipitate will be as shown in fig.1. A consequence of this type of transformation is that a cumulative shear, S, is produced that leads to a strain field in the surrounding zirconium matrix, as illustrated in fig.2a.


Author(s):  
R. E. Franck ◽  
J. A. Hawk ◽  
G. J. Shiflet

Rapid solidification processing (RSP) is one method of producing high strength aluminum alloys for elevated temperature applications. Allied-Signal, Inc. has produced an Al-12.4 Fe-1.2 V-2.3 Si (composition in wt pct) alloy which possesses good microstructural stability up to 425°C. This alloy contains a high volume fraction (37 v/o) of fine nearly spherical, α-Al12(Fe, V)3Si dispersoids. The improved elevated temperature strength and stability of this alloy is due to the slower dispersoid coarsening rate of the silicide particles. Additionally, the high v/o of second phase particles should inhibit recrystallization and grain growth, and thus reduce any loss in strength due to long term, high temperature annealing.The focus of this research is to investigate microstructural changes induced by long term, high temperature static annealing heat-treatments. Annealing treatments for up to 1000 hours were carried out on this alloy at 500°C, 550°C and 600°C. Particle coarsening and/or recrystallization and grain growth would be accelerated in these temperature regimes.


2001 ◽  
Vol 7 (S2) ◽  
pp. 1012-1013
Author(s):  
Uyen Tram ◽  
William Sullivan

Embryonic development is a dynamic event and is best studied in live animals in real time. Much of our knowledge of the early events of embryogenesis, however, comes from immunofluourescent analysis of fixed embryos. While these studies provide an enormous amount of information about the organization of different structures during development, they can give only a static glimpse of a very dynamic event. More recently real-time fluorescent studies of living embryos have become much more routine and have given new insights to how different structures and organelles (chromosomes, centrosomes, cytoskeleton, etc.) are coordinately regulated. This is in large part due to the development of commercially available fluorescent probes, GFP technology, and newly developed sensitive fluorescent microscopes. For example, live confocal fluorescent analysis proved essential in determining the primary defect in mutations that disrupt early nuclear divisions in Drosophila melanogaster. For organisms in which GPF transgenics is not available, fluorescent probes that label DNA, microtubules, and actin are available for microinjection.


2009 ◽  
Author(s):  
Tiny Jaarsma ◽  
Kristofer Franzén Årestedt ◽  
Jan Mårtensson ◽  
Kathleen Dracup ◽  
Anna Strömberg

2014 ◽  
Vol 47 (06) ◽  
Author(s):  
N Bergemann ◽  
K Boyle ◽  
WE Paulus

Sign in / Sign up

Export Citation Format

Share Document