Digitization of Real-Time Predictive Maintenance for High Speed Machine Equipment

2021 ◽  
pp. 132-140
Author(s):  
Rony Mitra ◽  
Mayank Shukla ◽  
Adrijit Goswami ◽  
Manoj Kumar Tiwari
Keyword(s):  
Real Time ◽  
High Speed ◽  
Predictive Maintenance ◽  
High Speed Machine

Discussion—Session III: High speed machine tools for aircraft production

1955 ◽  
Vol 34 (4) ◽  
pp. 224
Author(s):  
F.C. Cooke ◽  
S. Radcliffe ◽  
H.A. Chambers ◽  
C. Bromage ◽  
Menelaus ◽  
...  
Keyword(s):  
Machine Tools ◽  
High Speed ◽  
Discussion Session ◽  
Aircraft Production ◽  
High Speed Machine

High speed interferometric device for real-time correction of aero-optic effects

1995 ◽  
Author(s):  
Rod Clark ◽  
John Karpinsky ◽  
Gregg Borek ◽  
Eric Johnson
Keyword(s):  
Real Time ◽  
High Speed ◽  
Time Correction

Electrical Probing and Surface Imaging of Deep Sub-Micron Integrated Circuits

1999 ◽  
Author(s):  
Kenneth Krieg ◽  
Richard Qi ◽  
Douglas Thomson ◽  
Greg Bridges
Keyword(s):  
High Resolution ◽  
Integrated Circuits ◽  
Real Time ◽  
High Speed ◽  
Time Signal ◽  
Surface Imaging ◽  
Atomic Force ◽  
Submicron Structures ◽  
High Resolution Images ◽  
Capacitive Loading

Abstract A contact probing system for surface imaging and real-time signal measurement of deep sub-micron integrated circuits is discussed. The probe fits on a standard probe-station and utilizes a conductive atomic force microscope tip to rapidly measure the surface topography and acquire real-time highfrequency signals from features as small as 0.18 micron. The micromachined probe structure minimizes parasitic coupling and the probe achieves a bandwidth greater than 3 GHz, with a capacitive loading of less than 120 fF. High-resolution images of submicron structures and waveforms acquired from high-speed devices are presented.

Influence of the choice of wear criterion on the life of high speed machine manual taps

2020 ◽  
pp. 74-78
Author(s):  
A.E. Dreval
Keyword(s):  
Service Life ◽  
Structural Steel ◽  
Tool Life ◽  
High Speed ◽  
High Speed Steel ◽  
Parameter Dependence ◽  
Limiting State ◽  
Thread Cutting ◽  
Failure Life ◽  
High Speed Machine

The assessment of the limiting state of high-speed machine-manual taps in the processing of structural steel billets is considered. A general multi-parameter dependence is developed for calculating the criterion of allowable wear, which makes it possible to rationally use the tool life and normalize the cut amount during regrinding. Keywords thread cutting, tap, angle of the cutting part, criterion, high-speed steel, wear, failure, life, service life. [email protected]

Low-Cost High-Speed Techniques for Real-Time Simulation of Power Electronic Systems

2007 ◽  
Author(s):  
R. E. Crosbie ◽  
J. J. Zenor ◽  
R. Bednar ◽  
D. Word ◽  
N. G. Hingorani
Keyword(s):  
Real Time ◽  
High Speed ◽  
Low Cost ◽  
Electronic Systems ◽  
Power Electronic ◽  
Real Time Simulation ◽  
Time Simulation
Sign in / Sign up

Export Citation Format

Share Document