RETRACTED CHAPTER: Fundamentals of Solid Lubricants

2018 ◽  
pp. 1-32 ◽  
Author(s):  
Ajay Kumar Prajapati ◽  
Emad Omrani ◽  
Pradeep L. Menezes ◽  
Pradeep K. Rohatgi
Keyword(s):  
Solid Lubricants

Performance evaluation of whisker-reinforced ceramic tools under nano-sized solid lubricants assisted MQL turning of Co-based Haynes 25 superalloy

2021 ◽  
Author(s):  
Murat Sarıkaya ◽  
Şenol Şirin ◽  
Çağrı Vakkas Yıldırım ◽  
Turgay Kıvak ◽  
Munish Kumar Gupta
Keyword(s):  
Performance Evaluation ◽  
Solid Lubricants ◽  
Ceramic Tools

Friction and Wear Behaviors of Solid Lubricants/Polyimide Composites in Liquid Mediums

2010 ◽  
Vol 654-656 ◽  
pp. 2763-2766 ◽  
Author(s):  
Li Wen Mu ◽  
Xin Feng ◽  
Yi Jun Shi ◽  
Huai Yuan Wang ◽  
Xiao Hua Lu
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Tribological Properties ◽  
Alkaline Solution ◽  
Dry Friction ◽  
Friction And Wear ◽  
Solid Lubricants ◽  
Polyimide Composites ◽  
Inorganic Fillers ◽  
Ptfe Composites

The tribological properties of polyimide (PI) composites reinforced with graphite or MoS2 sliding in liquid alkali and water as well as dry friction were investigated using a ring-on-ring tester. The results show that the friction coefficient (μ) and wear rate (W) for both graphite/PI and MoS2/PI composites in different liquid mediums are μdry>μwater >μalkali and Wwater>Wdry >Walkali. Results also indicate that the friction coefficient and wear rate of the PI composites filled with different solid lubricants are μMoS2 >μgraphite and W MoS2 >Wgraphite in different liquid mediums. In addition, the hydrophobic inorganic fillers are fit for the reinforcement of polymer-based composites sliding in liquid mediums. It is also concluded from the authors’ work that the wear rate and friction coefficient of polymer-based (such as PI, PTFE) composites in the alkali lubricated conditions is lowest among all the friction conditions. This may be attributed to the ionic hydration in the alkaline solution.

Sintering of antifriction materials containing solid lubricants

1989 ◽  
Vol 28 (11) ◽  
pp. 890-893
Author(s):  
V. A. Al'tman ◽  
B. N. Dukhan ◽  
V. L. Memelov ◽  
E. G. Osipova
Keyword(s):  
Solid Lubricants ◽  
Antifriction Materials

scholarly journals Solid Lubricants

Nature ◽  
1920 ◽  
Vol 105 (2638) ◽  
pp. 372-372 ◽  
Author(s):  
L. A.
Keyword(s):  
Solid Lubricants

Comparative Evaluation of MoS2 and WS2 as Powder Lubricants in High Speed, Multi-Pad Journal Bearings

1999 ◽  
Vol 121 (3) ◽  
pp. 625-630 ◽  
Author(s):  
C. Fred Higgs ◽  
Crystal A. Heshmat ◽  
Hooshang Heshmat
Keyword(s):  
Comparative Evaluation ◽  
High Speed ◽  
Solid Lubricants ◽  
Extreme Environment ◽  
Journal Bearings ◽  
Lubricating Film ◽  
Constant Friction ◽  
Traction Coefficient ◽  
Limiting Value ◽  
Selection Of

As part of a program to develop solid/powder-lubricated journal bearings, a comparative evaluation has been performed to aid in determining whether MoS2 and WS2 powder are suitable lubricants for high-speed, extreme-environment multi-pad journal bearings. Plots of traction coefficients, friction, frictional power loss, and bearing pad temperature are presented as a means for comparing various powder lubricants. This paper primarily focuses on experiments carried out on a three-pad journal bearing and a disk-on-disk tribometer. Results showed that MoS2 traction curves resemble that of SAE 10 synthetic oil. Unlike liquid lubricants, powder films have a limiting shear strength property. Once the powder reaches this limiting value, the maximum traction coefficient is limited and the powder essentially shears along sliding walls. Experimental traction data shows evidence of this property in various powders. The thermal performance of the bearing was evaluated at speeds up to 30,000 rpm and loads up to 236 N. Although WS2 displayed constant friction coefficient and low temperature with increasing dimensionless load, MoS2 exhibited frictional behavior resembling that of a hydrodynamic lubricating film. In this paper, an attempt has been made to provide a criterion for the selection of solid lubricants for use in those tribosystems that may be operated in a high speed/load regime (i.e., high strain rates) as an alternative yard stick to conventional comparative approaches.

Development of Ni/h-BN Self-Lubricating Composite Powder by High-Energy Ball Milling

2016 ◽  
Vol 869 ◽  
pp. 277-282
Author(s):  
Moisés Luiz Parucker ◽  
César Edil da Costa ◽  
Viviane Lilian Soethe
Keyword(s):  
Ball Milling ◽  
Milling Time ◽  
Solid Lubricants ◽  
High Energy ◽  
High Energy Ball Milling ◽  
Second Phase ◽  
Average Particle ◽  
Composite Powders ◽  
The Matrix ◽  
Energy Ball

Solid lubricants have had good acceptance when used in problem areas where the conventional lubricants cannot be applied: under extreme temperatures, high charges and in chemically reactive environments. In case of materials manufactured by powder metallurgy, particles of solid lubricants powders can be easily incorporated to the matrix volume at the mixing stage. In operation, this kind of material provides a thin layer of lubricant that prevents direct contact between the surfaces. The present study aimed at incorporating particles of second phase lubricant (h-BN) into a matrix of nickel by high-energy ball milling in order to obtain a self-lubricating composite with homogeneous phase distribution of lubricant in the matrix. Mixtures with 10 vol.% of h-BN varying the milling time of 5, 10, 15 and 20 hours and their relationship ball/powder of 20:1 were performed. The effect of milling time on the morphology and microstructure of the powders was studied by X-ray diffraction, SEM and EDS. The composite powders showed reduction in average particle size with increasing milling time and the milling higher than 5 hours resulted in equiaxial particles and the formation of nickel boride.

Sign in / Sign up

Export Citation Format

Share Document