Integration of Fuzzy Logic with Response Surface Methodology for Predicting the Effect of Process Parameters on Build Time and Model Material Volume in FDM Process

2016 ◽  
pp. 195-206
Author(s):  
Manu Srivastava ◽  
Sachin Maheshwari ◽  
T. K. Kundra ◽  
Ramkrishna Yashaswi ◽  
Sandeep Rathee
Keyword(s):  
Response Surface Methodology ◽  
Fuzzy Logic ◽  
Response Surface ◽  
Process Parameters ◽  
Model Material ◽  
Build Time ◽  
Material Volume

Fiber laser processing of GFRP composites and multi-objective optimization of the process using response surface methodology

2018 ◽  
Vol 53 (11) ◽  
pp. 1459-1473 ◽  
Author(s):  
Shiva Dayal Rao B ◽  
Abhijeet Sethi ◽  
Alok Kumar Das
Keyword(s):  
Response Surface Methodology ◽  
Fiber Laser ◽  
Response Surface ◽  
Process Parameters ◽  
Heat Affected Zone ◽  
Cutting Speed ◽  
Kerf Width ◽  
Laser Irradiance ◽  
Input Process ◽  
Cut Surface

In the present investigation, a continuous wave fiber laser with maximum power of 400 W was used to cut a glass fiber reinforced plastic sheet of 4.56 mm thickness using Nitrogen as assisting gas. The influence processing parameters such as laser irradiance, gas pressure, and cutting speed on the cut surface quality were investigated by using response surface methodology. The different responses of laser cut surface such as upper kerf width, taper percentage along the cut depth, and heat-affected zone on the top surface were measured to analyze the influence of input process parameters on the responses. A statistical analysis on the obtained results was conducted and found that the optimum values of different input process parameters were laser irradiance: 8.28 × 105 watt/cm2, cutting speed: 600 mm/min and assisting gas pressure: 7.84 bar. The corresponding values of responses were upper kerf width: 177.4 µm, taper 0.73%, and heat-affected zone on top surface: 109.23 µm. The confirmation experiments were conducted with the obtained optimum parameter setting and observed that the predicted values and experimental values for upper kerf width, taper percentage and top surface heat-affected zone were within the error limits of 2.52%, 1.84%, and 0.45%, respectively. Furthermore, damages like loose fibers, interlayer fractures, evaporation of matrix material and fiber breakages were observed.

scholarly journals Effect of Process Parameters on the Surface Roughness and Kerf Width of Mild Steel during Plasma Arc Cutting Using Response Surface Methodology

2020 ◽  
Vol 5 (1) ◽  
Author(s):  
Ekhaesomi A Agbonoga ◽  
Oyewole Adedipe ◽  
Uzoma G Okoro ◽  
Fidelis J Usman ◽  
Kafayat T Obanimomo ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Analysis Of Variance ◽  
Process Parameters ◽  
Cutting Speed ◽  
Gas Pressure ◽  
Kerf Width ◽  
Plasma Arc ◽  
Plasma Arc Cutting

This study investigated the effects of process parameters of plasma arc cutting (PAC) of low carbon steel material using analysis of variance. Three process parameters, cutting speed, cutting current and gas pressure were considered and experiments were conducted based on response surface methodology (RSM) via the box-Behnken approach. Process responses viz. surface roughness (Ra) and kerf width of cut surface were measured for each experimental run. Analysis of Variance (ANOVA) was performed to get the contribution of process parameters on responses. Cutting current has the most significant effect of 33.43% on the surface roughness and gas pressure has the most significant effect on  kerf width of  41.99% . For minimum surface roughness and minimum kerf width, process parameters were optimized using the RSM. Keywords: Cutting speed, cutting current, gas pressure,   surface roughness, kerf width

Sign in / Sign up

Export Citation Format

Share Document