How to Connect Exponential Integrals to Optimal Process ?

1983 ◽  
pp. 17-25
Author(s):  
E. Combet
Keyword(s):  
Optimal Process

Sensitivity Analysis and Selection of Check Index of Signal Intersection Simulation Model Based on VISSIM

2019 ◽  
Vol 2 (5) ◽  
Author(s):  
Mengda Zhang ◽  
Chenjing Zhou ◽  
Tian-tian Zhang ◽  
Yan Han
Keyword(s):  
Sensitivity Analysis ◽  
Simulation Model ◽  
Optimal Process ◽  
Parameter Calibration ◽  
Index Set ◽  
The Core ◽  
Core Module ◽  
Simulation Parameter ◽  
Simulation Parameters ◽  
Selection Of

Selecting check index quantitatively is the core of the calibration of micro traffic simulation parameters at signal intersection. Five indexes in the node (intersection) module of VISSIM were selected as the check index set. Twelve simulation parameters in the core module were selected as the simulation parameters set. Optimal process of parameter calibration was proposed and model of the intersection of Huangcun west street and Xinghua street in Beijing was built in VISSIM to verify it. The sensitivity analysis between each check index and simulation parameter in their own set was conducted respectively. Sensitive parameter sets of different check indices were obtained and compared. The results show that different indexes have different size of set, and average vehicle delay's is maximum, so it's necessary to select index quantitatively. The results can provide references for scientific selection of the check indexes and improve the study efficiency of parameter calibration.

scholarly journals Mechanical properties optimization of the steering column based on multi-objective optimization design

2016 ◽  
Vol 8 (12) ◽  
pp. 168781401668294 ◽  
Author(s):  
Si Chen ◽  
Zhaohui Wang ◽  
Mi Lv
Keyword(s):  
Mechanical Properties ◽  
Process Parameters ◽  
Optimization Design ◽  
Strain Difference ◽  
Optimization Method ◽  
Equivalent Strain ◽  
Multi Objective Optimization ◽  
Optimal Process ◽  
Multi Objective ◽  
Initial Results

The mechanical properties of the steering column have a significant influence on the comfort and stability of a vehicle. In order for the mechanical properties to be improved, the rotary swaging process of the steering column is studied in this article. The process parameters, including axial feed rate, hammerhead speed, and hammerhead radial reduction, are systematically analyzed and optimized based on a multi-objective optimization design. The response surface methodology and the genetic algorithm are employed for optimal process parameters to be obtained. The maximum damage value, the maximum forming load, and the equivalent strain difference obtained with the optimal process parameters are, respectively, decreased by 30.09%, 7.44%, and 57.29% compared to the initial results. The comparative results present that the quality of the steering column is improved. The torque experiments and fatigue experiments are conducted with the optimal steering column. The maximum torque is measured to be 260 NM, and the service life is measured to be 2 weeks (40 NM, 2500 times), which are, respectively, increased by 8.3% and 8.69% compared to the initial results. The above results display that the mechanical properties of the steering column are optimized to verify the feasibility of the multi-objective optimization method.

Optimal process characteristics of melting of polyisoprene

2021 ◽  
Author(s):  
K. Mohanraj ◽  
Rajakumar S. Rai ◽  
M. Suresh ◽  
B. Logapriya ◽  
S. Marichamy ◽  
...  
Keyword(s):  
Optimal Process ◽  
Process Characteristics

scholarly journals On the existence of a solution for some distributed optimal control hyperbolic system

2000 ◽  
Vol 23 (5) ◽  
pp. 297-311 ◽  
Author(s):  
Dariusz Idczak ◽  
Stanislaw Walczak
Keyword(s):  
Optimal Control ◽  
Hyperbolic System ◽  
Convex Set ◽  
Linear Time ◽  
Time Varying ◽  
Optimal Process ◽  
Existence Of A Solution ◽  
Distributed Optimal Control ◽  
Absolutely Continuous ◽  
State Variable

We consider a Bolza problem governed by a linear time-varying Darboux-Goursat system and a nonlinear cost functional, without the assumption of the convexity of an integrand with respect to the state variable. We prove a theorem on the existence of an optimal process in the classes of absolutely continuous trajectories of two variables and measurable controls with values in a fixed compact and convex set.

Study on Extracting Potassium from Potassium Feldspar with Molten Salt Leaching Method

2012 ◽  
Vol 524-527 ◽  
pp. 1078-1081
Author(s):  
Jian Guo Song ◽  
Xin Zhi Wang ◽  
Shao Dan Xiao ◽  
Wei Liu
Keyword(s):  
Reaction Time ◽  
Molten Salt ◽  
Potassium Feldspar ◽  
Process Conditions ◽  
Temperature Reaction ◽  
Optimal Process ◽  
Potash Feldspar ◽  
Salt Leaching ◽  
Effects Of Temperature

This article aims to study the technology of extracting potassium from potassium feldspar with molten salt leaching method and to analyze the effects of temperature, reaction time and other factors on extracting potassium, concluding the optimal process conditions of extracting potassium with molten leaching method from potash feldspar.

Sign in / Sign up

Export Citation Format

Share Document