Comparative Stiffness and Damping Analysis for Various Flow Controlling Devices of Hole Entry Worn Hybrid Conical Journal Bearing Under the Variation of Speed

2021 ◽  
pp. 1455-1461
Author(s):  
Vikas M. Phalle ◽  
Sanjay R. Pawar
Keyword(s):  
Journal Bearing ◽  
Stiffness And Damping

Experimental and Theoretical Rotordynamic Characteristics of a Hybrid Journal Bearing

1997 ◽  
Vol 119 (1) ◽  
pp. 132-141 ◽  
Author(s):  
J. T. Sawicki ◽  
R. J. Capaldi ◽  
M. L. Adams
Keyword(s):  
Journal Bearing ◽  
Operating Conditions ◽  
Dynamic Force ◽  
Test Results ◽  
Force Measurements ◽  
Lubrication Equation ◽  
Load Cells ◽  
Theoretical Predictions ◽  
Stiffness And Damping

This paper describes an experimental and theoretical investigation of a four-pocket, oil-fed, orifice-compensated hydrostatic bearing including the hybrid effects of journal rotation. The test apparatus incorporates a double-spool-shaft spindle which permits independent control over the journal spin speed and the frequency of an adjustable-magnitude circular orbit, for both forward and backward whirling. This configuration yields data that enables determination of the full linear anisotropic rotordynamic model. The dynamic force measurements were made simultaneously with two independent systems, one with piezoelectric load cells and the other with strain gage load cells. Theoretical predictions are made for the same configuration and operating conditions as the test matrix using a finite-difference solver of Reynolds lubrication equation. The computational results agree well with test results, theoretical predictions of stiffness and damping coefficients are typically within thirty percent of the experimental results.

Tilting Pad Journal Bearings: A Discussion on Stability Calculation, Frequency Dependence, and Pad and Pivot Flexibility

2012 ◽  
Author(s):  
Jason C. Wilkes ◽  
Dara W. Childs
Keyword(s):  
Degrees Of Freedom ◽  
Journal Bearing ◽  
Operating Temperature ◽  
Excitation Frequency ◽  
Full Model ◽  
Stability Calculation ◽  
Damping Coefficients ◽  
Tilting Pad ◽  
Stiffness And Damping ◽  
Tilting Pad Journal Bearing

For several years, researchers have presented predictions showing that using a full tilting-pad journal bearing (TPJB) model (retaining all of the pad degrees of freedom) is necessary to accurately perform stability calculations for a shaft operating on TPJBs. This paper will discuss this issue, discuss the importance of pad and pivot flexibility in predicting impedance coefficients for the tilting-pad journal bearing, present measured changes in bearing clearance with operating temperature, and summarize the differences between measured and predicted frequency dependence of dynamic impedance coefficients. The current work presents recent test data for a 100 mm (4 in) five-pad TPJB tested in load on pad (LOP) configuration. Measured results include bearing clearance as a function of operating temperature, pad clearance and radial displacement of the loaded pad (the pad having the static load vector directed through its pivot), and frequency dependent stiffness and damping. Measured hot bearing clearances are approximately 30% smaller than measured cold bearing clearances and are inversely proportional to pad surface temperature; predicting bearing impedances with a rigid pad and pivot model using these reduced clearances results in overpredicted stiffness and damping coefficients that are several times larger than previous comparisons. The effect of employing a full bearing model versus a reduced bearing model (where only journal degrees of freedom are retained) in a stability calculation for a realistic rotor-bearing system is assessed. For the bearing tested, the bearing coefficients reduced at the frequency of the unstable eigenvalue (subsynchronously reduced) predicted a destabilizing cross-coupled stiffness coefficient at the onset of instability within 1% of the full model, while synchronously reduced coefficients for the lightly loaded bearing required 25% more destabilizing cross-coupled stiffness than the full model to cause system instability. The same stability calculation was performed using measured stiffness and damping coefficients at synchronous and subsynchronous frequencies. These predictions showed that both the synchronously measured stiffness and damping and predictions using the full bearing model were more conservative than the model using subsynchronously measured stiffness and damping, an outcome that is completely opposite from conclusions reached by comparing different prediction models. This contrasting outcome results from a predicted increase in damping with increasing excitation frequency at all speeds and loads; however, this increase in damping with increasing excitation frequency was only measured at the most heavily loaded conditions.

An Analytical Complete Model of Tilting-Pad Journal Bearing Considering Pivot Stiffness and Damping

2010 ◽  
Vol 133 (1) ◽  
Author(s):  
Zhiyong Yan ◽  
Yi Lu ◽  
Tiesheng Zheng
Keyword(s):  
Degrees Of Freedom ◽  
Journal Bearing ◽  
Local Coordinate System ◽  
Dynamical Behavior ◽  
Complete Model ◽  
Damping Coefficients ◽  
Tilting Pad ◽  
Generalized Force ◽  
Stiffness And Damping ◽  
Tilting Pad Journal Bearing

Considering the freedom of pad tilting and pad translation along preload orientation, an analytical complete model, as well as mathematical method, which contains 2n+2 degrees of freedom, is presented for calculating the dynamical characteristics of tilting-pad journal bearing. Based on the motion relationship of shaft and pad, the local coordinate system, the generalized displacement, and the generalized force vector are chosen. The concise transformation of generalized displacement, generalized force, and its Jacobian matrix between the local and global coordinate systems are built up in matrix form. A fast algorithm using the Newton–Raphson method for calculating the equilibrium position of journal and pads is proposed. The eight reduced stiffness and damping coefficients can be obtained assuming that the journal and all pads are subject to harmonic vibration. Numerical results show that the reduced damping coefficients and the threshold speed can be effectively enhanced by giving suitable pad pivot stiffness and damping simultaneously, and this analytical method can be applied to analyze dynamical behavior of the tilting-pad journal bearing rotor system.

A Variable Viscosity Approach for the Analysis of Steady State and Dynamic Characteristics of Two-Lobe Journal Bearing With TiO2 Based Nanolubricant

2017 ◽  
Author(s):  
Ashutosh Kumar ◽  
Sashindra Kumar Kakoty
Keyword(s):  
Steady State ◽  
Dynamic Characteristics ◽  
Journal Bearing ◽  
Volume Fraction ◽  
Variable Viscosity ◽  
Flow Coefficient ◽  
Viscosity Model ◽  
Nano Lubricant ◽  
The Stability ◽  
Stiffness And Damping

Steady-state and dynamic characteristics of two-lobe journal bearing, operating on TiO2 based Nano-lubricant has been obtained. The effective viscosity is obtained by using Krieger-Dougherty viscosity model for a given volume fraction of nanoparticle in the base fluid. Various bearing performance characteristics are then obtained by solving modified Reynolds equation for variable viscosity model and couple stress model. The stiffness and damping coefficients are also determined for various values of the volume fraction of the nanoparticle in the nanofluid. Results reveal that load carrying capacity and flow coefficient increase whereas friction variable decreases without affecting the stability condition of two-lobe journal bearing operating on TiO2 based nanolubricant. On the other hand attitude angle and dynamic coefficients remains constant for all the values of volume fraction of nanoparticle.

Dynamic Characteristics of TEHD Tilt Pad Journal Bearing Simulation Including Multiple Mode Pad Flexibility Model

1993 ◽  
Author(s):  
Jinsang Kim ◽  
Alan Palazzolo
Keyword(s):  
Heat Transfer ◽  
Elastic Deformation ◽  
Degrees Of Freedom ◽  
Journal Bearing ◽  
Variable Viscosity ◽  
Global Analysis ◽  
Analysis Method ◽  
Stiffness And Damping ◽  
Modal Coordinates ◽  
Good Agreement

Abstract An approach for incorporating the heat transfer and elastic deformation effects into dynamic coefficient calculation is presented. A global analysis method is used, which finds the equilibrium pad tilt angles at each eccentricity position and includes cross-film variable viscosity, heat transfer effects in the lubricant, elastic deformation, heat conduction effects in the pads, and elastic deformation effect in the pivots. Deflection modes are used to approximate deformation of the top surface of the pads. The dynamic coefficients of a single pad are calculated at the equilibrium state of the bearing, based on numerical perturbation with respect to the bearing degrees of freedom. These include journal position, pad rotation, pivot deformation, and modal coordinates. The stiffness and damping coefficients are calculated and show very good agreement with experimental and numerical results from the existing literature.

Three-Dimensional Thermo-Elasto-Hydrodynamic Computational Fluid Dynamics Model of a Tilting Pad Journal Bearing—Part II: Dynamic Response

2019 ◽  
Vol 141 (6) ◽  
Author(s):  
Jongin Yang ◽  
Alan Palazzolo
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Dynamic Response ◽  
Journal Bearing ◽  
Three Dimensional ◽  
Static Response ◽  
Damping Coefficients ◽  
Tilting Pad ◽  
Stiffness And Damping ◽  
Tilting Pad Journal Bearing

Part II presents a novel approach for predicting dynamic coefficients for a tilting pad journal bearing (TPJB) using computational fluid dynamics (CFD) and finite element method (FEM), including fully coupled elastic deflection, heat transfer, and fluid dynamics. Part I presented a similarly novel, high fidelity approach for TPJB static response prediction which is a prerequisite for the dynamic characteristic determination. The static response establishes the equilibrium operating point values for eccentricity, attitude angle, deflections, temperatures, pressures, etc. The stiffness and damping coefficients are obtained by perturbing the pad and journal motions about this operating point to determine changes in forces and moments. The stiffness and damping coefficients are presented in “synchronously reduced form” as required by American Petroleum Institute (API) vibration standards. Similar to Part I, an advanced three-dimensional thermal—Reynolds equation code validates the CFD code for the special case when flow Between Pad (BP) regions is ignored, and the CFD and Reynolds pad boundary conditions are made identical. The results show excellent agreement for this validation case. Similar to the static response case, the dynamic characteristics from the Reynolds model show large discrepancies compared with the CFD results, depending on the Reynolds mixing coefficient (MC). The discrepancies are a concern given the key role that stiffness and damping coefficients serve instability and response predictions in rotordynamics software. The uncertainty of the MC and its significant influence on static and dynamic response predictions emphasizes a need to utilize the CFD approach for TPJB simulation in critical machines.

Influence of Wear on the Performance of Multirecess Hydrostatic Journal Bearing Operating With Micropolar Lubricant

2010 ◽  
Vol 132 (2) ◽  
Author(s):  
E. Rajasekhar Nicodemus ◽  
Satish C. Sharma
Keyword(s):  
Journal Bearing ◽  
Dynamic Performance ◽  
Flow Equation ◽  
Performance Characteristics ◽  
Wear Depth ◽  
Damping Coefficients ◽  
Load Line ◽  
Wide Range ◽  
Load Arrangement ◽  
Stiffness And Damping

The objective of the present work is to study theoretically the influence of wear on the performance of four-pocket capillary-compensated hydrostatic journal bearing operating with micropolar lubricant. In the present study, the lubricant containing additives and contaminants is modeled as micropolar fluid. The modified Reynolds equation for micropolar lubricant is solved using finite element method along with capillary restrictor flow equation as a constraint together with appropriate boundary conditions. The performance characteristics of a capillary-compensated four-pocket worn hydrostatic journal bearing operating with micropolar lubricant have been presented for a wide range of values of nondimensional external load, wear depth parameter, and micropolar parameters. The simulated results have also been presented for two different loading arrangements. In arrangement I, the load line acts through centers of the pockets, whereas in arrangement II, the load line bisects the land between two pockets. The simulated results suggest that a bearing lubricated with lubricant having higher micropolar effect has better static and dynamic performance characteristics as compared with Newtonian lubricant but the bearing lubricated with lubricant having higher micropolar effect is predominantly affected by the wear vis a vis static characteristics parameters as compared with Newtonian lubricant for both loading arrangements. However, in the case of stiffness and damping coefficients, loading arrangement II shows a significant higher enhancement in the value of direct stiffness and damping coefficients in z-direction due to micropolar effect as compared with load arrangement I. And also, the effect of wear on stiffness and damping coefficients in z-direction for bearing operating with micropolar lubricant is of same order as Newtonian lubricant for the loading arrangement II. A similar behavior is observed for the case of stiffness and damping coefficients in x-direction for loading arrangement I.

Steady-State and Dynamic Behaviour of Multi-Recess Hybrid Oil Journal Bearings

1979 ◽  
Vol 21 (5) ◽  
pp. 345-351 ◽  
Author(s):  
M. K. Ghosh ◽  
B. C. Majumdar ◽  
J. S. Rao
Keyword(s):  
Perturbation Theory ◽  
Steady State ◽  
Theoretical Analysis ◽  
Dynamic Behaviour ◽  
Journal Bearing ◽  
Load Capacity ◽  
Journal Bearings ◽  
Time Dependent ◽  
Damping Coefficients ◽  
Stiffness And Damping

A theoretical analysis of the steady-state and dynamic characteristics of multi-recess hybrid oil journal bearings is presented. A perturbation theory for small vibrations is used to solve an incompressible, finite journal bearing with a time-dependent term. Load capacity, attitude angle, friction parameter, stiffness and damping coefficients are evaluated for a capillary-compensated bearing.

scholarly journals Dynamic Stiffness and Damping Characteristics of a High-Temperature Air Foil Journal Bearing

2001 ◽  
Vol 44 (4) ◽  
pp. 657-663 ◽  
Author(s):  
Samuela Howard ◽  
Christopher Dellacorte ◽  
Mark J. Valco ◽  
Joseph M. Prahl ◽  
Hooshang Heshmat
Keyword(s):  
High Temperature ◽  
Journal Bearing ◽  
Dynamic Stiffness ◽  
Damping Characteristics ◽  
Stiffness And Damping
Sign in / Sign up

Export Citation Format

Share Document