Effect of Machining Parameters on Surface Integrity in End Milling of Inconel 625

2019 ◽  
pp. 505-515
Author(s):  
Ramesh Rajguru ◽  
Hari Vasudevan
Keyword(s):  
Surface Integrity ◽  
End Milling ◽  
Inconel 625 ◽  
Machining Parameters

Experimental Investigation to Improve Surface Integrity of Biomedical Devices by End-Milling AISI 316L Stainless Steel

2015 ◽  
Vol 789-790 ◽  
pp. 141-145 ◽  
Author(s):  
Muhammad Yasir ◽  
Turnad Lenggo Ginta ◽  
Adam Umar Alkali ◽  
Mohammad Danish
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Surface Integrity ◽  
Feed Rate ◽  
316L Stainless Steel ◽  
End Milling ◽  
Cutting Speed ◽  
Machining Parameters ◽  
Aisi 316L ◽  
Aisi 316L Stainless Steel

This paper presents the influence of machining parameters namely cutting speed and feed rate on the machinability enhancement of AISI 316L stainless steel, in terms of surface integrity using end-milling with coated tungsten carbide tool (TiAlN). Optical microscopy, Scanning Electron Microscopy (SEM) and surface roughness measurement were used to analyze the surface integrity in terms surface topography and hardness test. A multi view approach is adopted to study the effect of different cutting parameters on the surface integrity of AISI 316L stainless steel. It was found that high cutting speed and low feed rate influence the surface roughness. Low surface roughness makes AISI 316L stainless steel more corrosion resistant which prevents wear of the implants.

Parameter Optimization of Ball End Milling Process on Inconel 718 Using RSM and TLBO Algorithm

2015 ◽  
Vol 15 (3) ◽  
pp. 293-300 ◽  
Author(s):  
Nandkumar N. Bhopale ◽  
Nilesh Nikam ◽  
Raju S. Pawade
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Surface Integrity ◽  
Inconel 718 ◽  
Tool Path ◽  
End Milling ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Ball End Milling

AbstractThis paper presents the application of Response Surface Methodology (RSM) coupled with Teaching Learning Based Optimization Technique (TLBO) for optimizing surface integrity of thin cantilever type Inconel 718 workpiece in ball end milling. The machining and tool related parameters like spindle speed, milling feed, axial depth of cut and tool path orientation are optimized with considerations of multiple response like deflection, surface roughness, and micro hardness of plate. Mathematical relationship between process parameters and deflection, surface roughness and microhardness are found out by using response surface methodology. It is observed that after optimizing the process that at the spindle speed of 2,000 rpm, feed 0.05 mm/tooth/rev, plate thickness of 5.5 mm and 15° workpiece inclination with horizontal tool path gives favorable surface integrity.

Prediction of Surface Roughness in Compressed Air Jet Assisted High Speed End Milling of Silicon Using Diamond Coated Tools

2012 ◽  
Vol 576 ◽  
pp. 41-45
Author(s):  
A.K.M. Nurul Amin ◽  
M.A. Mahmud ◽  
M.D. Arif
Keyword(s):  
Mathematical Model ◽  
Surface Roughness ◽  
Surface Finish ◽  
High Speed ◽  
End Milling ◽  
Silicon Wafers ◽  
Compressed Air ◽  
Machining Parameters ◽  
High Quality ◽  
Ductile Mode

The majority of semiconductor devices are made up of silicon wafers. Manufacturing of high-quality silicon wafers includes numerous machining processes, including end milling. In order to end mill silicon to a nano-meteric surface finish, it is crucial to determine the effect of machining parameters, which influence the machining transition from brittle to ductile mode. Thus, this paper presents a novel experimental technique to study the effects of machining parameters in high speed end milling of silicon. The application of compressed air, in order to blow away the chips formed, is also investigated. The machining parameters’ ranges which facilitate the transition from brittle to ductile mode cutting as well as enable the attainment of high quality surface finish and integrity are identified. Mathematical model of the response parameter, the average surface roughness (Ra) is subsequently developed using RSM in terms of the machining parameters. The model was determined, by Analysis of Variance (ANOVA), to have a confidence level of 95%. The experimental results show that the developed mathematical model can effectively describe the performance indicators within the controlled limits of the factors that are being considered.

Surface Integrity Studies in Ball End Milling of Thin Shaped Cantilever Inconel 718

2014 ◽  
Author(s):  
Nandkumar N. Bhopale ◽  
Raju S. Pawade
Keyword(s):  
Surface Integrity ◽  
Inconel 718 ◽  
Tool Path ◽  
Surface Defects ◽  
End Milling ◽  
Surface Region ◽  
Lower Surface ◽  
Machined Surface ◽  
Ball End Milling ◽  
Integrity Analysis

The paper presents the surface integrity analysis in ball end milling of thin shaped cantilever plate of Inconel 718. It is noticed that the workpiece deflection has significantly contributed to machined surface integrity in terms of surface topography and subsurface microhardness. The ball end milling performed with 15° workpiece inclination with horizontal tool path produced higher surface integrity which varies with the location of machined surface region. In general, the mid portion of the machined plate shows lower surface roughness and microhardness with less surface defects.

scholarly journals Effects of the Tribological Behaviour of h-BN MQL Nano Cutting Fluid (NCF-MQL) on Turning Inconel 625

2019 ◽  
Vol 11 (4) ◽  
pp. 107-121 ◽  
Author(s):  
Chinmaya PADHY ◽  
Pariniti SINGH
Keyword(s):  
Optimization Technique ◽  
Minimum Quantity Lubrication ◽  
Chip Morphology ◽  
Machining Process ◽  
Cutting Fluid ◽  
Inconel 625 ◽  
Machining Parameters ◽  
Machining Performance ◽  
Tribological Behaviour ◽  
Machined Surface

Minimum quantity lubrication (MQL) is currently a widely used lubricating technique during machining, in which minimum amount of lubricant in the form of mist is delivered to the machining interface, thus helps to reduce the negative effects caused to the environment and human health. Further, to enhance the productivity of machining process specifically for hard-to-cut materials, nano cutting fluid (suitably mixed nano materials with conventional cutting fluid) is used as an alternative method to conventional lubrication (wet) in MQL. In this study, h-BN nano cutting fluid was formulated with 0.1% vol. concentration of h-BN in conventional cutting fluid (Servo- ‘S’) for NCF-MQL technique and its tribological behaviors on machining(turning) performance of Inconel 625 were studied and compared with other lubricating conditions (dry, wet, MQL conventional). The tribological effects were analyzed in terms of tool wear analysis, chip morphology along with statistical analysis for machined surface and evolved cutting forces during machining. The optimal input machining parameters for experiments were defined by the use of Taguchi and Grey relational based multi response optimization technique. Finally, the tribological study shows that the use of h-BN NCF-MQL is a viable and sustainable option for improving machining performance of hard- to- cut material like Inconel 625.

Sign in / Sign up

Export Citation Format

Share Document