Mechanical properties and curing characteristics of unsaturated polyesters synthesized for large casting

1995 ◽  
Vol 35 (1-2) ◽  
pp. 229-236 ◽  
Author(s):  
Abdel-Azim A. Abdel-Azim
Keyword(s):  
Mechanical Properties ◽  
Unsaturated Polyesters ◽  
Curing Characteristics ◽  
Large Casting

scholarly journals Study of clay minerals effect on curing characteristics of polymer blends and physical-mechanical properties of prepared vulcanizates

2018 ◽  
Vol 157 ◽  
pp. 07010
Author(s):  
Beáta Pecušová ◽  
Mariana Pajtášová ◽  
Zuzana Mičicová ◽  
Darina Ondrušová ◽  
Andrea Feriancová ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Polymer Blends ◽  
Clay Minerals ◽  
Structural Type ◽  
Partial Replacement ◽  
Curing Characteristics ◽  
Dioctahedral Smectite ◽  
The Common ◽  
The Given

The given paper deals with the study of the properties of clay minerals, namely montmorillonite and moreover, it is focused on effect of these clay minerals on the curing characteristics of the polymer blends and the physical-mechanical properties of prepared vulcanizates. Montmorillonite is a major clay mineral which has a wide application in many industrial branches. It belongs to the group of dioctahedral smectite minerals with structural type in the ratio of 2:1. Characteristics of prepared modified and organomodified clay minerals are based on sulphur vulcanisation accelerators which are used for the preparation of real polymer blend where they represent a partial replacement of the common carbon black filler and then, the effect on the curing characteristics of polymer blends as well as physical-mechanical properties of the prepared vulcanizates are investigated. The results exhibit that the clay-based filler (modified and organomodified clay minerals) can be used as a partial replacement while the quality of the prepared blends is preserved.

scholarly journals Novolac/Phenol-Containing Phthalonitrile Blends: Curing Characteristics and Composite Mechanical Properties

Polymers ◽  
2020 ◽  
Vol 12 (1) ◽  
pp. 126 ◽  
Author(s):  
Hanqi Zhang ◽  
Bing Wang ◽  
Yanna Wang ◽  
Heng Zhou
Keyword(s):  
Mechanical Properties ◽  
Fracture Strain ◽  
Mechanical Test ◽  
Gelation Time ◽  
Mechanical Analysis ◽  
Curing Temperature ◽  
Hydroxyl Group ◽  
Rheological Analysis ◽  
Curing Characteristics ◽  
Ft Ir

The phenol-containing phthalonitrile resin is a kind of self-curing phthalonitrile resin with high-temperature resistance and excellent properties. However, the onefold phthalonitrile resin is unattainable to cured completely, and the brittleness of the cured product is non-negligible. This paper focuses on solving the above problems by blending novolac resin into phenol-containing phthalonitrile. Under the action of abundant hydroxyl group, the initial curing temperature and gelation time at 170 °C decrease by 88 °C and 2820 s, respectively, monitored by DSC and rheological analysis. FT-IR spectra of copolymers showed that the addition of novolac increased the conversion rate of nitrile. When the novolac mass fraction is 10%, the peak of nitrile group disappears, which means the complete reaction. The mechanical test of blends composites shows that the maximum fracture strain of 10 wt% novolac addition is 122% higher than those of neat phthalonitrile composites on account of the introduction of flexible novolac chain segments. The mechanical properties are sensitive to elevated post-cured temperature; this is consistent with the result of morphological investigation using SEM. Finally, the dynamic mechanical analysis indicated that the glass transition temperature heightened with the increase of novolac content and post-curing temperature.

Improvement of Mechanical Properties of Unsaturated Polyesters by Acrylonitrile

1992 ◽  
Vol 31 (3-4) ◽  
pp. 221-227 ◽  
Author(s):  
G[ubar]ng[obar]r G[ubar]nd[ubar]z ◽  
Adnan Deniz
Keyword(s):  
Mechanical Properties ◽  
Unsaturated Polyesters

Relationship between Curing Characteristics and Rheological/Mechanical Properties of Soft-feel Coatings for Automotive Plastic Parts

Polymer Korea ◽  
2018 ◽  
Vol 42 (2) ◽  
pp. 303-310
Author(s):  
Sung Ho Yoon ◽  
Dong Geun Lee ◽  
Na Hee Kim ◽  
Kevin Injoe Jung ◽  
Choon Soo Lee ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Curing Characteristics ◽  
Plastic Parts
Sign in / Sign up

Export Citation Format

Share Document