Anisotropy of sintered antifriction materials containing a solid lubricant

1970 ◽  
Vol 9 (2) ◽  
pp. 156-159 ◽  
Author(s):  
L. S. Abramova ◽  
A. B. Al'tman ◽  
V. é. Vainshtein ◽  
Ya. A. Gluskin ◽  
V. L. Memelov
Keyword(s):  
Solid Lubricant ◽  
Antifriction Materials

Determination of the optimum amount of the solid lubricant of composite antifriction materials

1988 ◽  
Vol 27 (6) ◽  
pp. 485-488
Author(s):  
G. Kh. Karapetyan ◽  
N. L. Akopov ◽  
F. Kh. Karapetyan ◽  
N. N. Manukyan
Keyword(s):  
Solid Lubricant ◽  
Optimum Amount ◽  
Antifriction Materials ◽  
Composite Antifriction

The elaboration of novel scientific instrumentation and antifriction materials for performing the «Material-Friction» space experiment

2002 ◽  
Vol 8 (5-6) ◽  
pp. 28-34 ◽  
Author(s):  
G.D. Gamulya ◽  
◽  
V.V. Skorokhod ◽  
V.P. Solntsev ◽  
M.N. Surdu ◽  
...  
Keyword(s):  
Space Experiment ◽  
Scientific Instrumentation ◽  
Antifriction Materials

Improvement of die life with surface texture control and solid lubricant

2012 ◽  
Vol 67 (2) ◽  
pp. 153-157 ◽  
Author(s):  
O. Furukimi ◽  
M. Aramaki ◽  
K. Abe ◽  
H. Fukaura ◽  
N. Yamada
Keyword(s):  
Surface Texture ◽  
Solid Lubricant ◽  
Die Life

Fullerene-like Nanoparticles of WS2 as a Promising Protection from Erosive Wear of Gun Bore Nozzles

2020 ◽  
Vol 16 (1) ◽  
pp. 62-70 ◽  
Author(s):  
Narimane Rezgui ◽  
Danica Simić ◽  
Choayb Boulahbal ◽  
Dejan Micković
Keyword(s):  
Mass Loss ◽  
Solid Lubricant ◽  
Erosive Wear ◽  
Mechanical Resistance ◽  
Protective Function ◽  
Protective Layers ◽  
Total Mass Loss ◽  
Mass Losses ◽  
Before And After ◽  
Tube Life

Background: Erosive wear causes increase in the bore diameter of firearms barrels and nozzles. Most responsible factors for this erosion are friction and heat generated during the shot. Protection from erosive wear is very important for gun tube life cycle, and various protection methods are used: adding phlegmatizers in gunpowder composition or applying protective layers on the gun bore inner surface. Objective: In this research, a possibility is examined to protect the surface of a nozzle exposed to gunpowder erosion applying a layer of tungsten disulfide fullerene-like nanoparticles, IF-WS2, known as outstanding solid lubricant of a great mechanical resistance. Methods: Nanoparticles on the nozzle surface before and after the gunfire tests were observed using scanning electron microscopy/energy dispersive X-ray spectroscopy. Gunfire tests were performed on designed erosion device. Temperatures in the defined position near the affected surface were measured with thermocouples and compared for the nozzles with and without nanoprotection, as well as the nozzle mass loss after each round. Results: For the sample with IF-WS2 lower temperatures after firing and lower mass losses were observed. Mass loss after first round was 25.6% lower for the sample with protective nanoparticles layer, and the total mass loss was about 5% lower after five rounds. After the first round the nozzle without IF-WS2 was heated up to a temperature which was for 150.8°C higher than the nozzle with IF-WS2. Conclusion: Protective function of IF-WS2 is the most pronounced for the first round. The observed results encourage its further application in firearms gun bores protection.

Improvement of thread turning process using micro-hole textured solid-lubricant embedded tools

2021 ◽  
pp. 095440542110199
Author(s):  
Salman Khani ◽  
Seyedhamidreza Shahabi Haghighi ◽  
Mohammad Reza Razfar ◽  
Masoud Farahnakian
Keyword(s):  
Surface Roughness ◽  
Mechanical Strength ◽  
Solid Lubricant ◽  
Operating Cost ◽  
Contact Length ◽  
Solid Lubrication ◽  
Turning Process ◽  
Micro Holes ◽  
Micro Hole ◽  
Cutting Inserts

In this paper, the thread turning of aluminum 7075-T6 alloy is studied using micro-hole textured solid-lubricant embedded carbide inserts. The primary focus of this work is to enhance the performance of the thread turning process for producing high quality threaded parts. To achieve this, micro-holes were generated by laser micro-machining on the rake face of tools and then, MoS2 and CNT (carbon nanotube) solid-lubricants were embedded into micro-holes. The effects of micro-holes and solid-lubrication on the performance of the thread turning process were examined using traditional tool ( T0), micro-hole textured tool ( T1), micro-hole textured MoS2 embedded tool ( T2), and micro-hole textured CNT embedded tool ( T3). In this study, cutting forces, chip-tool contact length, built-up edge (BUE), surface roughness, and operating cost were investigated. The influence of micro-hole generation on the mechanical strength of cutting inserts was evaluated using the finite element method. The results showed that the fabrication of the micro-holes on the rake surface of cutting inserts has no significant effect on the mechanical strength of the tools. The comparisons of our method with traditional tools demonstrated that the cutting performance improved in the threading process. Our results reveal that the main cutting force, radial thrust force, surface roughness, built-up edge, and chip-tool contact length reduced 37.1%, 40.9%, 37.9%, 58.3%, and 38.2%, respectively, as T3 tools are applied in this process. A cost analysis, based on estimated tooling costs, showed that the T3 tool can yield an 18% reduction in overall operating cost.

Tribological characteristics of MoS2–Nb solid lubricant film in different tribo-test conditions

2008 ◽  
Vol 203 (5-7) ◽  
pp. 766-770 ◽  
Author(s):  
Ihsan Efeoglu ◽  
Özlem Baran ◽  
Fatih Yetim ◽  
Sabri Altıntaş
Keyword(s):  
Solid Lubricant ◽  
Lubricant Film ◽  
Tribological Characteristics ◽  
Test Conditions

Co–P alloy matrix composite deposits reinforced by nano-MoS2 solid lubricant: An alternative tribological coating to hard chromium coatings

2021 ◽  
Vol 159 ◽  
pp. 106956
Author(s):  
Mehdad Fathi ◽  
Mir Saman Safavi ◽  
Soheil Mahdavi ◽  
Sahand Mirzazadeh ◽  
Vahid Charkhesht ◽  
...  
Keyword(s):  
Matrix Composite ◽  
Solid Lubricant ◽  
Alloy Matrix ◽  
Hard Chromium ◽  
Composite Deposits

scholarly journals Free-Forging of Pure Titanium with High Reduction of Thickness by Plasma-Carburized SKD11 Dies

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2536
Author(s):  
Tatsuhiko Aizawa ◽  
Tomoaki Yoshino ◽  
Yohei Suzuki ◽  
Tomomi Shiratori
Keyword(s):  
Solid Lubricant ◽  
Pure Titanium ◽  
Solid Lubrication ◽  
Single Shot ◽  
Contact Interface ◽  
Forging Process ◽  
Titanium Wire ◽  
High Reduction ◽  
Residual Strains

A tool steel type SKD11 punch was plasma carburized at 673 K for 14.4 ks at 70 Pa to make carbon supersaturation. This carburized SKD11 punch was employed for upsetting the pure titanium wire with the diameter of 1.00 mm up to the reduction of thickness by 70% in a single shot. Its contact interface to titanium work was analyzed to describe the anti-galling behavior in this forging. Little trace of titanium proved that the galling process was suppressed by the in situ solid lubrication. The isolated free carbon agglomerates are wrought as a solid lubricant to sustain the galling-free forging process. This anti-galling upsetting reduced the residual strains in the forged wires. A long titanium wire with a length of 45 mm was incrementally upset to yield the titanium ribbon with a thickness of 0.3 mm, the width of 2.3 mm, and the length of 50 mm. The grain size of original pure titanium was much reduced to 2 μm on average. A micro-pillared microtexture was imprinted onto this forged titanium ribbon.

Sign in / Sign up

Export Citation Format

Share Document