Improvement of thread turning process using micro-hole textured solid-lubricant embedded tools

2021 ◽  
pp. 095440542110199
Author(s):  
Salman Khani ◽  
Seyedhamidreza Shahabi Haghighi ◽  
Mohammad Reza Razfar ◽  
Masoud Farahnakian
Keyword(s):  
Surface Roughness ◽  
Mechanical Strength ◽  
Solid Lubricant ◽  
Operating Cost ◽  
Contact Length ◽  
Solid Lubrication ◽  
Turning Process ◽  
Micro Holes ◽  
Micro Hole ◽  
Cutting Inserts

In this paper, the thread turning of aluminum 7075-T6 alloy is studied using micro-hole textured solid-lubricant embedded carbide inserts. The primary focus of this work is to enhance the performance of the thread turning process for producing high quality threaded parts. To achieve this, micro-holes were generated by laser micro-machining on the rake face of tools and then, MoS2 and CNT (carbon nanotube) solid-lubricants were embedded into micro-holes. The effects of micro-holes and solid-lubrication on the performance of the thread turning process were examined using traditional tool ( T0), micro-hole textured tool ( T1), micro-hole textured MoS2 embedded tool ( T2), and micro-hole textured CNT embedded tool ( T3). In this study, cutting forces, chip-tool contact length, built-up edge (BUE), surface roughness, and operating cost were investigated. The influence of micro-hole generation on the mechanical strength of cutting inserts was evaluated using the finite element method. The results showed that the fabrication of the micro-holes on the rake surface of cutting inserts has no significant effect on the mechanical strength of the tools. The comparisons of our method with traditional tools demonstrated that the cutting performance improved in the threading process. Our results reveal that the main cutting force, radial thrust force, surface roughness, built-up edge, and chip-tool contact length reduced 37.1%, 40.9%, 37.9%, 58.3%, and 38.2%, respectively, as T3 tools are applied in this process. A cost analysis, based on estimated tooling costs, showed that the T3 tool can yield an 18% reduction in overall operating cost.

COMPARISON OF PREPARATION METHODS IN TERMS OF TOOL LIFE AND SURFACE ROUGHNESS

2021 ◽  
Vol 2021 (4) ◽  
pp. 4836-4840
Author(s):  
ROBERT STRAKA ◽  
◽  
JOZEF PETERKA ◽  
TOMAS VOPAT ◽  
◽  
...  
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Cutting Parameters ◽  
Turning Process ◽  
Machined Surface ◽  
Preparation Methods ◽  
Machined Surface Roughness ◽  
Cutting Inserts ◽  
Drag Finishing ◽  
Edge Preparation

The article compares two cutting edge preparation methods and their influence on the machined surface roughness of the difficult to cut nickel alloy Inconel 718 and the tool wear of cutting inserts made of cemented carbide. The manufacturing and preparation process of cutting inserts used in the experiment were made by Dormer Pramet. The preparation methods used in the experiment were drag finishing and brushing. Cutting parameters did not change during the whole turning process to maintain the same conditions in each step of the process and were determined based on tests for a semi-finishing operation of the turning process. To obtain durability of 25 to 30 minutes with controlled development of the tool wear the cutting parameters were determined with cooperation with the cutting inserts manufacturer.

Preparations and Properties of Solid Lubricants Coating on High-Speed Steel Tools

2008 ◽  
Vol 392-394 ◽  
pp. 538-542
Author(s):  
Suo Xia Hou ◽  
Xiao Ming Jia ◽  
C. Wu
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
Solid Lubricant ◽  
Testing Machine ◽  
High Speed Steel ◽  
Solid Lubricants ◽  
Solid Lubrication ◽  
Mixture Ratio ◽  
Solid Lubricant Coating ◽  
Cutting Test

This paper presents that the high-speed steel tools with solid lubrication material coating can cut without fluid because it has the quality of self-lubrication. With the help of M-2 friction and wearing testing machine and KYKY2800 scan electron microscope, the coating preparation technology and mixture ratio of solid lubrication material in complex coating can be optimized. The results show: phosphate treatment can increase the power of the tools’ surface adsorbing solid lubricant, and the frictional behaviour of solid lubrication coating is excellent when surface roughness of phosphate coating is Ra 2μm~Ra 4μm; molybdenum bisulfide, graphite and trioxid aluminium are mixed together and form a kind of complex coating which has better antifriction effect. The cutting test shows that the solid lubricant coating on the high-speed steel tools can be helpful in increasing the service life of the tools, decreasing the cutting resistance, and reducing the chip deformation and surface roughness of finished work.

scholarly journals Free-Forging of Pure Titanium with High Reduction of Thickness by Plasma-Carburized SKD11 Dies

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2536
Author(s):  
Tatsuhiko Aizawa ◽  
Tomoaki Yoshino ◽  
Yohei Suzuki ◽  
Tomomi Shiratori
Keyword(s):  
Solid Lubricant ◽  
Pure Titanium ◽  
Solid Lubrication ◽  
Single Shot ◽  
Contact Interface ◽  
Forging Process ◽  
Titanium Wire ◽  
High Reduction ◽  
Residual Strains

A tool steel type SKD11 punch was plasma carburized at 673 K for 14.4 ks at 70 Pa to make carbon supersaturation. This carburized SKD11 punch was employed for upsetting the pure titanium wire with the diameter of 1.00 mm up to the reduction of thickness by 70% in a single shot. Its contact interface to titanium work was analyzed to describe the anti-galling behavior in this forging. Little trace of titanium proved that the galling process was suppressed by the in situ solid lubrication. The isolated free carbon agglomerates are wrought as a solid lubricant to sustain the galling-free forging process. This anti-galling upsetting reduced the residual strains in the forged wires. A long titanium wire with a length of 45 mm was incrementally upset to yield the titanium ribbon with a thickness of 0.3 mm, the width of 2.3 mm, and the length of 50 mm. The grain size of original pure titanium was much reduced to 2 μm on average. A micro-pillared microtexture was imprinted onto this forged titanium ribbon.

Simulation of Plasto-Elastohydrodynamic Lubrication in Line Contacts of Infinite and Finite Length

2015 ◽  
Vol 137 (4) ◽  
Author(s):  
Tao He ◽  
Jiaxu Wang ◽  
Zhanjiang Wang ◽  
Dong Zhu
Keyword(s):  
Surface Roughness ◽  
Finite Length ◽  
3D Model ◽  
Three Dimensional ◽  
Elastohydrodynamic Lubrication ◽  
Axial Direction ◽  
Contact Length ◽  
Line Contact ◽  
Line Contacts ◽  
3D Surface Topography

Line contact is common in many machine components, such as various gears, roller and needle bearings, and cams and followers. Traditionally, line contact is modeled as a two-dimensional (2D) problem when the surfaces are assumed to be smooth or treated stochastically. In reality, however, surface roughness is usually three-dimensional (3D) in nature, so that a 3D model is needed when analyzing contact and lubrication deterministically. Moreover, contact length is often finite, and realistic geometry may possibly include a crowning in the axial direction and round corners or chamfers at two ends. In the present study, plasto-elastohydrodynamic lubrication (PEHL) simulations for line contacts of both infinite and finite length have been conducted, taking into account the effects of surface roughness and possible plastic deformation, with a 3D model that is needed when taking into account the realistic contact geometry and the 3D surface topography. With this newly developed PEHL model, numerical cases are analyzed in order to reveal the PEHL characteristics in different types of line contact.

In Situ: A Novel Approach for the Production of Micro Holes

2010 ◽  
Vol 126-128 ◽  
pp. 885-890
Author(s):  
K.P. Somashekhar ◽  
N. Ramachandran ◽  
Jose Mathew
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Feed Rate ◽  
Machining Parameters ◽  
Average Roughness ◽  
Arithmetic Average ◽  
Quantitative Correlation ◽  
Good Surface ◽  
Novel Approach ◽  
Micro Holes

This work is on the preparation of microelectrodes for μ-EDM operation using μ-WEDG process. Electrodes of Ø500 μm are fabricated with various discharge energy machining conditions. Effects of gap voltage, capacitance & feed rate on the surface finish of the electrodes and overcut of the thus produced micro holes are investigated. The profile of microelectrodes is measured using surface roughness tester with 2μm stylus interfaced with SURFPAK software. The study demonstrated that for brass electrodes an arithmetic average roughness value as low as 1.7μm and an overcut of 3 µm could be achieved. The significant machining parameters are found using ANOVA. Surface of the produced microelectrodes are examined using Scanning Electron Microscope. μ-WEDG process parameters could be adjusted to achieve good surface integrity on microelectrodes. Experimental results showed that the surface roughness of microelectrodes depended primarily on feed rate of the electrode. The observations showed the clear and quantitative correlation existing between the micrometer level surface quality and process parameters. The resulting microelectrodes are found to be of exceptionally high quality and could be used for μ- EDM operation on different types of work materials.

Comparative Analysis between Conventional and Dry Turning

2017 ◽  
Vol 261 ◽  
pp. 267-274
Author(s):  
Pantelis N. Botsaris ◽  
Chaido Kyritsi ◽  
Dimitris Iliadis
Keyword(s):  
Experimental Data ◽  
Surface Roughness ◽  
Cutting Tool ◽  
Spindle Motor ◽  
Air Cooling ◽  
Machining Parameters ◽  
Turning Process ◽  
Dry Cutting ◽  
Cold Air ◽  
Cooling And Lubrication

In this paper, there is an attempt to monitor and evaluate machining parameters when turning 34CrNiMo6 material under different cooling and lubrication conditions. The machining parameters concerned are temperature of the cutting tool and the workpiece, level of vibrations of the cutting tool, surface roughness of the workpiece, noise levels of the turning process and current drawn by the main spindle motor. Four different experimental machining scenarios were completed, specifically: conventional wet turning process, dry cutting and two additional modes employing cooling by cold air. Experimental data were acquired and recorded by an optimally designed network of sensors. Experimental data were statistically analyzed in order to reach conclusions. According to the research that has been done, although, overall, minimum cutting tool and workpiece temperatures were observed under wet machining, cold air cooling is capable of achieving comparable cooling results to wet machining. The lowest values of surface roughness were achieved by wet machining, whereas the lowest level of cutting tool vibrations were observed under cold air cooling.

Analysis of tool vibration and surface roughness during turning process of tempered steel samples using Taguchi method

2021 ◽  
pp. 095440892110019
Author(s):  
Menderes Kam ◽  
Mustafa Demirtaş
Keyword(s):  
Surface Roughness ◽  
Taguchi Method ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Machining Parameters ◽  
Turning Process ◽  
Machining Time ◽  
Tool Vibration ◽  
Control Factors ◽  
Tempered Steel

This study analyzed the tool vibration (Vib) and surface roughness (Ra) during turning of AISI 4340 (34CrNiMo6) tempered steel samples using Taguchi Method. In this context, Taguchi design L18 (21 × 32) was used to analyze the experimental results. The vibration amplitude values from cutting tools were recorded for different machining parameters, control factors; two different sample hardness (46 and 53 HRc), three different cutting speeds (180, 220, 260 m.min−1), and feed rates (0.08, 0.14, 0.20 mm.rev−1) were selected. The machining parameters giving optimum Vib and Ra values were determined. Regression analysis is applied to predict values of Vib and Ra. Analysis of variance was used to determine the effects of machining parameters on the Vib and Ra values. The most important machining parameters were found to be the feed rate, sample hardness, and cutting speed for Vib and Ra, respectively. The lowest Vib and Ra values were obtained in 46 HRc sample as 0.0022 gRMS and 0.255 µm, respectively. The surface quality can be improved by reducing the sources of vibration by using appropriate machining parameters. As a result, there is a significant relationship between Ra and Vib. The lower Ra values were found during turning process of tempered steel samples according to the literature studies. It is suggested that the process can be preferred as an alternative process to grinding process due to lower cost and machining time. In application of the turning of experiment samples by ceramic cutting tool, a substantial technological and economical benefit has been observed.

Sign in / Sign up

Export Citation Format

Share Document