Plastic deformation of glassy amorphous polymers: influence of strain rate

1985 ◽  
Vol 20 (2) ◽  
pp. 438-448 ◽  
Author(s):  
J. M. Lefebvre ◽  
B. Escaig
Keyword(s):  
Plastic Deformation ◽  
Strain Rate ◽  
Amorphous Polymers

Formability of Explosive Welded Mg/Al Bimetallic Bar

2016 ◽  
Vol 716 ◽  
pp. 114-120 ◽  
Author(s):  
Sebastian Mróz ◽  
Piotr Szota ◽  
Teresa Bajor ◽  
Andrzej Stefanik
Keyword(s):  
Plastic Deformation ◽  
Strain Rate ◽  
Process Parameters ◽  
Metal Forming ◽  
Explosive Welding ◽  
Physical Modelling ◽  
Main Process ◽  
Compression Tests ◽  
Welding Method

The paper presents the results of physical modelling of the plastic deformation of the Mg/Al bimetallic specimens using the Gleeble 3800 simulator. The plastic deformation of Mg/Al bimetal specimens characterized by the diameter to thickness ratio equal to 1 was tested in compression tests. The aim of this work was determination of the range of parameters as temperature and strain rate that mainly influence on the plastic deformation of Mg/Al bars during metal forming processes. The tests were carried out for temperature range from 300 to 400°C for different strain rate values. The stock was round 22.5 mm-diameter with an Al layer share of 28% Mg/Al bars that had been produced using the explosive welding method. Based on the analysis of the obtained testing results it has been found that one of the main process parameters influencing the plastic deformation the bimetal components is the initial stock temperature and strain rate values.

scholarly journals A New Set-Up to Investigate Plastic Deformation of Face Centered Cubic Metals in High Strain Rate Loading

2014 ◽  
Vol 8 (2) ◽  
Author(s):  
Ehsan Etemadi ◽  
Jamal Zamani ◽  
Alessandro Francesconi ◽  
Mohammad V. Mousavi ◽  
Cinzia Giacomuzzo
Keyword(s):  
Plastic Deformation ◽  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Face Centered Cubic ◽  
Cubic Metals ◽  
Face Centered ◽  
Set Up ◽  
Strain Rate Loading

Effect of Grain Size on Deformation Twinning Behavior of Ti6Al4V Alloy

2015 ◽  
Vol 830-831 ◽  
pp. 337-340
Author(s):  
Ashish Kumar Saxena ◽  
Manikanta Anupoju ◽  
Asim Tewari ◽  
Prita Pant
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
Strain Rate ◽  
Deformation Behavior ◽  
Deformation Behaviour ◽  
Air Cooling ◽  
Specific Strength ◽  
Aerospace Applications ◽  
Β Phase ◽  
Plastic Deformation Behavior

An understanding of the plastic deformation behavior of Ti6Al4V (Ti64) is of great interest because it is used in aerospace applications due to its high specific strength. In addition, Ti alloys have limited slip systems due to hexagonal crystal structure; hence twinning plays an important role in plastic deformation. The present work focuses upon the grain size effect on plastic deformation behaviour of Ti64. Various microstructures with different grain size were developed via annealing of Ti64 alloy in α-β phase regime (825°C and 850°C) for 4 hours followed by air cooling. The deformation behavior of these samples was investigated at various deformation temperature and strain rate conditions. Detailed microstructure studies showed that (i) smaller grains undergoes twinning only at low temperature and high strain rate, (ii) large grain samples undergo twinning at all temperatures & strain rates, though the extent of twinning varied.

scholarly journals Molecular Dynamics Simulation of Crack Propagation in Single-Crystal Aluminum Plate with Central Cracks

2017 ◽  
Vol 2017 ◽  
pp. 1-12 ◽  
Author(s):  
Jun Ding ◽  
Lu-sheng Wang ◽  
Kun Song ◽  
Bo Liu ◽  
Xia Huang
Keyword(s):  
Molecular Dynamics ◽  
Plastic Deformation ◽  
Crack Propagation ◽  
Strain Rate ◽  
Single Crystal ◽  
Crack Length ◽  
Crack Growth ◽  
Plastic Yield ◽  
Model Size ◽  
Dislocation Multiplication

The crack propagation process in single-crystal aluminum plate (SCAP) with central cracks under tensile load was simulated by molecular dynamics method. Further, the effects of model size, crack length, temperature, and strain rate on strength of SCAP and crack growth were comprehensively investigated. The results showed that, with the increase of the model size, crack length, and strain rate, the plastic yield point of SCAP occurred in advance, the limit stress of plastic yield decreased, and the plastic deformability of material increased, but the temperature had less effect and sensitivity on the strength and crack propagation of SCAP. The model size affected the plastic deformation and crack growth of the material. Specifically, at small scale, the plastic deformation and crack propagation in SCAP are mainly affected through dislocation multiplication and slip. However, the plastic deformation and crack propagation are obviously affected by dislocation multiplication and twinning in larger scale.

Creep and Relaxation of Oxygen-Free Copper

1943 ◽  
Vol 10 (2) ◽  
pp. A101-A105
Author(s):  
Evan A. Davis
Keyword(s):  
Plastic Deformation ◽  
Strain Rate ◽  
Different Types

Abstract This paper contains results of creep and relaxation tests on an oxygen-free copper at temperatures up to 235 C. The effect of the stress and the temperature upon the strain rate has been noted and an effort has been made to correlate the results of the two different types of tests by using various theories of plastic deformation.

Sign in / Sign up

Export Citation Format

Share Document