Dynamic Properties of Geologic Specimens Subjected to Split-Hopkinson Pressure Bar Compression Testing at the University of Kentucky

2018 ◽  
Vol 37 (2) ◽  
pp. 897-913
Author(s):  
Russell Lamont ◽  
Jhon Silva
Keyword(s):  
Split Hopkinson Pressure Bar ◽  
Dynamic Properties ◽  
Compression Testing ◽  
Hopkinson Pressure Bar ◽  
University Of Kentucky ◽  
Split Hopkinson ◽  
Pressure Bar ◽  
The University

scholarly journals Study on the dynamic properties of AM-SLM AlSi10Mg alloy using the Split Hopkinson Pressure Bar (SHPB) technique

2018 ◽  
Vol 183 ◽  
pp. 04005 ◽  
Author(s):  
Bar Nurel ◽  
Moshe Nahmany ◽  
Adin Stern ◽  
Nahum Frage ◽  
Oren Sadot
Keyword(s):  
Strain Rate ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Properties ◽  
Rate Sensitivity ◽  
Strain Rate Range ◽  
Strain Rates ◽  
Hopkinson Pressure Bar ◽  
Static Mechanical ◽  
Split Hopkinson ◽  
Pressure Bar

Additive manufacturing by Selective Laser Melting of metals is attracting substantial attention, due to its advantages, such as short-time production of customized structures. This technique is useful for building complex components using a metallic pre-alloyed powder. One of the most used materials in AMSLM is AlSi10Mg powder. Additively manufactured AlSi10Mg may be used as a structural material and it static mechanical properties were widely investigated. Properties in the strain rates of 5×102–1.6×103 s-1 and at higher strain rates of 5×103 –105 s-1 have been also reported. The aim of this study is investigation of dynamic properties in the 7×102–8×103 s-1 strain rate range, using the split Hopkinson pressure bar technique. It was found that the dynamic properties at strain-rates of 1×103–3×103 s-1 depend on a build direction and affected by heat treatment. At higher and lower strain-rates the effect of build direction is limited. The anisotropic nature of the material was determined by the ellipticity of samples after the SHPB test. No strain rate sensitivity was observed.

Quasi-Static and High Strain Rate Uniaxial Compressive Response of Recycled Polycarbonate from Industrial Waste

2020 ◽  
Vol 1012 ◽  
pp. 89-93
Author(s):  
Anderson Oliveira da Silva ◽  
Ricardo Pondé Weber ◽  
Sergio Neves Monteiro
Keyword(s):  
Industrial Waste ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Properties ◽  
Hopkinson Pressure Bar ◽  
Mechanical Recycling ◽  
Static Compression ◽  
Compressive Response ◽  
Split Hopkinson ◽  
Pressure Bar ◽  
Quasi Static Compression

This work evaluates the mechanical and dynamic behavior of recycled polycarbonate (rPC) from industrial waste. This study aims to verify whether the recycled process adopted for polycarbonate promotes both mechanical and dynamic properties values under compressive stress, similar to those found for virgin polycarbonate. The mechanical recycling of the rPC was carried out using the thermoforming technique in a thermal press. Two tests were carried out to evaluate the dynamic response of rPC. The quasi-static compression test was performed on a universal machine. The dynamic in a split Hopkinson pressure bar was performed with three different strain rates. The results showed that the mechanical and primary recycling adopted in this work promoted values of yield stress in compression (77 MPa) and dynamic (up to 118 MPa), close to or superior to those reported so far in the literature.

Dynamic Constitutive Relation of EMC

2010 ◽  
Vol 129-131 ◽  
pp. 988-992
Author(s):  
Bo Wang ◽  
Tong Chen ◽  
Xue Feng Shu
Keyword(s):  
Yield Strength ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Properties ◽  
Strain Rates ◽  
Hopkinson Pressure Bar ◽  
Static Tests ◽  
Good Accordance ◽  
Different Temperatures ◽  
Split Hopkinson ◽  
Pressure Bar

In this paper, dynamic properties of EMC were studied at different temperatures and different strain rates. Firstly EMC was investigated by quasi-static tests. Secondly a series of dynamic compressive experiments of EMC were conducted using the Split Hopkinson Pressure Bar (SHPB) at sectional height of strain rates. Thirdly EMC constants in ZWT model were determined from experiments. Corresponding measurements were conducted at temperatures ranging from 20°C to 160°C. The results indicate that the yield strength and flow stress of EMC increase remarkably with the increase of strain rate and it is shows that the assembled curve is fit good accordance with actual the experimental curve. However, the yield strength of EMC is a little change with the increase of temperature which is ranging from 20°C to 160°C.

scholarly journals Experimental and Numerical Evaluation of Rock Dynamic Test with Split-Hopkinson Pressure Bar

2017 ◽  
Vol 2017 ◽  
pp. 1-12
Author(s):  
Kang Peng ◽  
Ke Gao ◽  
Jian Liu ◽  
Yujiao Liu ◽  
Zhenyu Zhang ◽  
...  
Keyword(s):  
Split Hopkinson Pressure Bar ◽  
Dynamic Properties ◽  
Dynamic Test ◽  
Propagation Distance ◽  
Sine Wave ◽  
Pulse Loading ◽  
Hopkinson Pressure Bar ◽  
Split Hopkinson ◽  
Pressure Bar ◽  
Stress Uniformity

Feasibility of rock dynamic properties by split-Hopkinson pressure bar (SHPB) was experimentally and numerically evaluated with ANSYS/LS-DYNA. The effects of different diameters, different loading rates, and different propagation distances on wave dispersion of input bars in SHPB with rectangle and half-sine wave loadings were analyzed. The results show that the dispersion effect on the diameter of input bar, loading rate, and propagation distance under half-sine waveform loading is ignorable compared with the rectangle wave loading. Moreover, the degrees of stress uniformity under rectangle and half-sine input wave loadings are compared in SHPB tests, and the time required for stress uniformity is calculated under different above-mentioned loadings. It is confirmed that the stress uniformity can be realized more easily using the half-sine pulse loading compared to the rectangle pulse loading, and this has significant advantages in the dynamic test of rock-like materials. Finally, the Holmquist-Johnson-Concrete constitutive model is introduced to simulate the failure mechanism and failure and fragmentation characteristics of rock under different strain rates. And the numerical results agree with that obtained from the experiment, which confirms the effectiveness of the model and the method.

scholarly journals Determination of the high-strain rate elastic modulus of printing resins using two different split Hopkinson pressure bars

2021 ◽  
Author(s):  
S. Aghayan ◽  
S. Bieler ◽  
K. Weinberg
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Properties ◽  
Compression Tests ◽  
Hopkinson Pressure Bar ◽  
Split Hopkinson ◽  
Pressure Bar ◽  
Strain Rate Loading

AbstractThe usage of resin-based materials for 3D printing applications has been growing over the past decades. In this study, two types of resins, namely a MMA-based resin and an ABS-based tough resin, are subjected to compression tests on a split Hopkinson pressure bar to deduce their dynamic properties under high strain rate loading.Two Hopkinson bar setups are used, the first one is equipped with aluminum bars and the second one with PMMA bars. From the measured strain waves, elastic moduli at high strain rates are derived. Both setups lead to values of $E=3.4$ E = 3.4 –3.8 GPa at a strain rate of about 250 s−1. Numerical simulations support the experiments. Moreover, considering the waves gained from the two different bar setups, PMMA bars appear to be well-suited for testing resin samples and are therefore recommended for such applications.

scholarly journals Dynamic High Strain Rate Characterization of Lithium-Ion Nickel–Cobalt–Aluminum (NCA) Battery Using Split Hopkinson Tensile/Pressure Bar Methodology

Energies ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 5061
Author(s):  
Hafiz Fadillah ◽  
Sigit Puji Santosa ◽  
Leonardo Gunawan ◽  
Akbar Afdhal ◽  
Agus Purwanto
Keyword(s):  
Dynamic Behavior ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Properties ◽  
Strain Curve ◽  
Lithium Ion ◽  
Thin Foil ◽  
Hopkinson Pressure Bar ◽  
Split Hopkinson ◽  
Pressure Bar

The dynamic behavior of the lithium-ion battery is evaluated by simulating the full battery system and each corresponding component, including the jellyroll and thin-foil electrodes. The thin-foil electrodes were evaluated using a novel design of split Hopkinson tensile bar (SHTB), while the jellyroll was evaluated using the split Hopkinson pressure bar (SHPB). A new stacking method was employed to strengthen the stress wave signal of the thin-foil electrodes in the SHTB simulation. The characteristic of the stress–strain curve should remain the same regardless of the amount of stacking. The jellyroll dynamic properties were characterized by using the SHPB method. The jellyroll was modeled with Fu-Chang foam and modified crushable foam and compared with experimental results at the loading speeds of 20 and 30 m/s. The dynamic behavior compared very well when it was modeled with Fu-Chang foam. These studies show that the dynamic characterization of Li-ion battery components can be evaluated using tensile loading of stacked layers of thin foil aluminum and copper with SHTB methodology as well as the compressive loading of jellyroll using SHPB methodology. Finally, the dynamic performance of the full system battery can be simulated by using the dynamic properties of each component, which were evaluated using the SHTB and SHPB methodologies.

scholarly journals A Comparative Study on Rock Properties in Splitting and Compressive Dynamic Tests

2018 ◽  
Vol 2018 ◽  
pp. 1-12
Author(s):  
Nan Wu ◽  
Zhende Zhu ◽  
Yaojun Zhou ◽  
Shihu Gao
Keyword(s):  
Strain Rate ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Properties ◽  
Tensile Tests ◽  
Rock Properties ◽  
Hopkinson Pressure Bar ◽  
Rock Samples ◽  
Dimensionless Stress ◽  
Split Hopkinson ◽  
Pressure Bar

The dynamic properties of rock in splitting (tensile) and compressive tests are the focus of rock dynamic mechanics research. In this study, a split Hopkinson pressure bar (SHPB) apparatus was used to assess the comparability and strain rate effect of rock samples under two kinds of load conditions. With an increase in impact velocity under compression and splitting (tensile) tests, the strain rate of the samples increased continuously. The rock properties and strain rate in the two kinds of samples exhibited clear similarities: the dimensionless stress-strain curves of the rock samples were similar under the same strain rates. The peak strength and elastic modulus of the two kinds of samples increased with an increase in the strain rate. The number of cracks increased from intergranular to transgranular failure. The rack initiation value of the two kinds of samples was close at the same strain rate and declined with an increase in the strain rate as evidenced by a power function.

Dynamic properties of pultruded natural fibre reinforced composites using Split Hopkinson Pressure Bar technique

2010 ◽  
Vol 31 (9) ◽  
pp. 4209-4218 ◽  
Author(s):  
Mohd Firdaus Omar ◽  
Hazizan Md Akil ◽  
Zainal Arifin Ahmad ◽  
A.A.M. Mazuki ◽  
Takashi Yokoyama
Keyword(s):  
Split Hopkinson Pressure Bar ◽  
Dynamic Properties ◽  
Natural Fibre ◽  
Reinforced Composites ◽  
Hopkinson Pressure Bar ◽  
Split Hopkinson ◽  
Pressure Bar ◽  
Fibre Reinforced Composites
Sign in / Sign up

Export Citation Format

Share Document