Constructing reliable PCM and OTS devices with an interfacial carbon layer

2019 ◽  
Vol 30 (22) ◽  
pp. 20037-20042
Author(s):  
Kun Ren ◽  
Xing Duan ◽  
Qinqin Xiong ◽  
Yangyang Li ◽  
Shilong Lv ◽  
...  
2013 ◽  
Vol 2013 ◽  
pp. 1-5 ◽  
Author(s):  
A. Kuchuk ◽  
V. Kladko ◽  
Z. Adamus ◽  
M. Wzorek ◽  
M. Borysiewicz ◽  
...  

Nickel-based contacts with additional interfacial layer of carbon, deposited on n-type 4H-SiC, were annealed at temperatures ranging from 600 to 1000°C and the evolution of the electrical and structural properties were analyzed by I-V measurements, SIMS, TEM, and Raman spectroscopy. Ohmic contact is formed after annealing at 800°C and minimal specific contact resistance of about 2.0×10-4 Ω cm2 has been achieved after annealing at 1000°C. The interfacial carbon is amorphous in as-deposited state and rapidly diffuses and dissolves in nickel forming graphitized carbon. This process activates interfacial reaction between Ni and SiC at lower temperature than usual and causes the formation of ohmic contact at relatively low temperature. However, our results show that the specific contact resistance as well as interface quality of contacts was not improved, if additional layer of carbon is placed between Ni and SiC.


1995 ◽  
Vol 103 (1195) ◽  
pp. 288-292 ◽  
Author(s):  
Kenji MATSUNAGA ◽  
Toshihiro ISHIKAWA ◽  
Shinji KAJII ◽  
Toshihiko HOGAMI ◽  
Yasuhiko KOHTOKU

2006 ◽  
Vol 527-529 ◽  
pp. 863-866
Author(s):  
Wei Jie Lu ◽  
J.A. Michel ◽  
C.M. Lukehart ◽  
W.E. Collins ◽  
W.C. Mitchel

Ohmic contacts on SiC have been investigated extensively in the past decade. However, the mechanism for ohmic contact formation has been a troublesome issue. The interfacial structures at the atomic scale responsible for forming ohmic contacts have not been revealed. Our previous results have shown that carbon can form ohmic contacts on SiC after thermal annealing, and that an interfacial carbon layer between Ni and the SiC improves the contacts significantly. In this study, we have investigated the interactions between Ni and carbon, and ohmic contact formation on SiC using x-ray diffraction (XRD) and Raman spectroscopy. After annealing, ohmic behavior was observed and Ni graphite intercalated compounds (GICs) were found on Ni/C/SiC structures. Unlike conventional graphite intercalated compounds, the Ni atoms substitute for carbon atoms in the graphitic networks in these Ni-GICs. XRD peaks at 21.6° due to the Ni graphitic intercalation compound (Ni-GIC) and at 26.3° due to graphite have been observed. The distance between graphitic sheets is 0.403nm in the Ni graphite intercalated compounds, whereas it is ~20% larger in the graphite. The thickness of the interfacial carbon layer does not affect the formation of Ni-GIC.


Author(s):  
G. Das ◽  
R. E. Omlor

Fiber reinforced titanium alloys hold immense potential for applications in the aerospace industry. However, chemical reaction between the fibers and the titanium alloys at fabrication temperatures leads to the formation of brittle reaction products which limits their development. In the present study, coated SiC fibers have been used to evaluate the effects of surface coating on the reaction zone in the SiC/IMI829 system.IMI829 (Ti-5.5A1-3.5Sn-3.0Zr-0.3Mo-1Nb-0.3Si), a near alpha alloy, in the form of PREP powder (-35 mesh), was used a茸 the matrix. CVD grown AVCO SCS-6 SiC fibers were used as discontinuous reinforcements. These fibers of 142μm diameter contained an overlayer with high Si/C ratio on top of an amorphous carbon layer, the thickness of the coating being ∽ 1μm. SCS-6 fibers, broken into ∽ 2mm lengths, were mixed with IMI829 powder (representing < 0.1vol%) and the mixture was consolidated by HIP'ing at 871°C/0. 28GPa/4h.


Author(s):  
Michel Fialin ◽  
Guy Rémond

Oxygen-bearing minerals are generally strong insulators (e.g. silicates), or if not (e.g. transition metal oxides), they are included within a rock matrix which electrically isolates them from the sample holder contacts. In this respect, a thin carbon layer (150 Å in our laboratory) is evaporated on the sections in order to restore the conductivity. For silicates, overestimated oxygen concentrations are usually noted when transition metal oxides are used as standards. These trends corroborate the results of Bastin and Heijligers on MgO, Al2O3 and SiO2. According to our experiments, these errors are independent of the accelerating voltage used (fig.l).Owing to the low density of preexisting defects within the Al2O3 single-crystal, no significant charge buildup occurs under irradiation at low accelerating voltage (< 10keV). As a consequence, neither beam instabilities, due to electrical discharges within the excited volume, nor losses of energy for beam electrons before striking the sample, due to the presence of the electrostatic charge-induced potential, are noted : measurements from both coated and uncoated samples give comparable results which demonstrates that the carbon coating is not the cause of the observed errors.


Author(s):  
Minakhi Pujari ◽  
Joachim Frank

In single-particle analysis of macromolecule images with the electron microscope, variations of projections are often observed that can be attributed to the changes of the particle’s orientation on the specimen grid (“rocking”). In the multivariate statistical analysis (MSA) of such projections, a single factor is often found that expresses a large portion of these variations. Successful angle calibration of this “rocking factor” would mean that correct angles can be assigned to a large number of particles, thus facilitating three-dimensional reconstruction.In a study to explore angle calibration in factor space, we used 40S ribosomal subunits, which are known to rock around an axis approximately coincident with their long axis. We analyzed micrographs of a field of these particles, taken with 20° tilt and without tilt, using the standard methods of alignment and MSA. The specimen was prepared with the double carbon-layer method, using uranyl acetate for negative staining. In the MSA analysis, the untilted-particle projections were used as active, the tilted-particle projections as inactive objects. Upon tilting, those particles whose rocking axes are parallel to the tilt axis will change their appearance in the same way as under the influence of rocking. Therefore, each vector, in factor space, joining a tilted and untilted projection of the same particle can be regarded as a local 20-degree calibration bar.


Sign in / Sign up

Export Citation Format

Share Document