Rapid Pyrolysis of YBa2Cu3O7-δ Films by Fluorine-Free Polymer-Assisted Chemical Solution Deposition Approach

2019 ◽  
Vol 32 (12) ◽  
pp. 3747-3753
Author(s):  
X. Yang ◽  
W. T. Wang ◽  
L. Liu ◽  
B. L. Huo ◽  
M. J. Wang ◽  
...  
Coatings ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 31 ◽  
Author(s):  
Minjuan Li ◽  
Pablo Cayado ◽  
Manuela Erbe ◽  
Alexandra Jung ◽  
Jens Hänisch ◽  
...  

SmBa2Cu3O7-δ (SmBCO) films have been prepared by chemical solution deposition starting from extremely-low-fluorine solutions (7% fluorine with respect to standard full trifluoroacetate solutions). Smooth and homogeneous SmBCO films could be achieved at heating rates of up to 20 °C/min during pyrolysis. The best films were achieved at a crystallization temperature of 810 °C and 50 ppm of oxygen partial pressure. At these conditions, the ~270 nm thick SmBCO films grow mostly c-axis-oriented with J c sf values at 77 K of ~2 MA/cm2 and critical temperatures Tc of up to 95.0 K. These results demonstrate that using extremely-low-fluorine solutions is very attractive since the production rate can be largely increased due to the solutions’ robustness during pyrolysis retaining a remarkable quality of the grown films. Nevertheless, further optimization of the growth process is needed to improve the superconducting properties of the films.


Coatings ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 307
Author(s):  
Diana Griesiute ◽  
Dovydas Karoblis ◽  
Lina Mikoliunaite ◽  
Aleksej Zarkov ◽  
Andrei N. Salak ◽  
...  

In the present work, polycrystalline Bi0.67La0.33Fe0.5Sc0.5O3 thin films were synthesized using a simple and cost-effective chemical solution deposition process employing the spin coating technique. In order to check the feasibility of the fabrication of thin films on various types of substrates, the films were deposited on Pt-coated silicon, silicon, sapphire, corundum, fused silica and glass. Based on the results of thermogravimetric analysis of precursor and thermal stability study, it was determined that the optimal annealing temperature for the formation of perovskite structure is 600 °C. It was observed that the relative intensity of the pseudocubic peaks (001)p and (011)p in the XRD patterns is influenced by the nature of substrates, suggesting that the formed crystallites have some preferred orientation. Roughness of the films was determined to be dependent on the nature of the substrate.


Author(s):  
Sucheta Sengupta ◽  
Rinki Aggarwal ◽  
Yuval Golan

This review article gives an overview of different complexing agents used during chemical deposition of metal chalcogenide thin films and their role in controlling the resultant morphology by effective complexation of the metal ion.


1999 ◽  
Vol 14 (11) ◽  
pp. 4395-4401 ◽  
Author(s):  
Seung-Hyun Kim ◽  
D. J. Kim ◽  
K. M. Lee ◽  
M. Park ◽  
A. I. Kingon ◽  
...  

Ferroelectric SrBi2Ta2O9 (SBT) thin films on Pt/ZrO2/SiO2/Si were successfully prepared by using an alkanolamine-modified chemical solution deposition method. It was observed that alkanolamine provided stability to the SBT solution by retarding the hydrolysis and condensation rates. The crystallinity and the microstructure of the SBT thin films improved with increasing annealing temperature and were strongly correlated with the ferroelectric properties of the SBT thin films. The films annealed at 800 °C exhibited low leakage current density, low voltage saturation, high remanent polarization, and good fatigue characteristics at least up to 1010 switching cycles, indicating favorable behavior for memory applications.


RSC Advances ◽  
2015 ◽  
Vol 5 (94) ◽  
pp. 76783-76787 ◽  
Author(s):  
H. L. Wang ◽  
X. K. Ning ◽  
Z. J. Wang

Au–LaNiO3 (Au–LNO) nanocomposite films with 3.84 at% Au were firstly fabricated by one-step chemical solution deposition (CSD), and their electrical properties were investigated.


1997 ◽  
Vol 36 (Part 1, No. 9B) ◽  
pp. 5930-5934 ◽  
Author(s):  
Wataru Sakamoto ◽  
Akihiro Kawase ◽  
Toshinobu Yogo ◽  
Shin-ichi Hirano

Sign in / Sign up

Export Citation Format

Share Document