Correlation of heat treatment temperature and phase composition in nanodispersed precursors based on systems TiO2, ZrO2, TiO2–Y2O3–ZrO2

2013 ◽  
Vol 53 (6) ◽  
pp. 411-416
Author(s):  
V. G. Konakov ◽  
N. V. Borisova ◽  
S. N. Golubev ◽  
E. N. Solov’eva ◽  
V. M. Ushakov
Keyword(s):  
Heat Treatment ◽  
Phase Composition ◽  
Heat Treatment Temperature ◽  
Treatment Temperature

Phase Transformation of Coal at High Temperature

2014 ◽  
Vol 809-810 ◽  
pp. 815-821
Author(s):  
Xiao Hu Hua ◽  
Xiao Gang Wang ◽  
Jia Qing Yang ◽  
Shu He Lu ◽  
Li Rong Deng ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Phase Transformation ◽  
Phase Composition ◽  
High Temperature ◽  
Internal Migration ◽  
Heat Treatment Temperature ◽  
Functional Group ◽  
Treatment Temperature ◽  
Conductive Phase ◽  
Higher Temperature

Anthracite and bitumite were processed respectively at 1400°C,1700°C, 2000°C, 2200°C, 2400°C and 2600°C,and their chemical composition,resistivity,microstructure, phase composition,and the internal migration of molecular functional group were tested and characterized. The results indicate that moisture, ash and volatile in coal have gradually shifted and lost with the elevation of heat treatment temperature, while the higher temperature, the quicker and completer phase change. Heat treatment can make the coal transform from approximately insulative phase to conductive phase,. Furthermore, as the temperature increases, the conductive phase transformation effect is better. The higher the heat treatment temperature of coal, the more amorphous carbon transforming into crystalline carbon completely, but the less types of phases .

Effects of Heat Treatment Temperature on Photocatalytic Activity of TiO2/SiO2 Composite Aerogels

2013 ◽  
Vol 27 (10) ◽  
pp. 1079-1083
Author(s):  
Zhao-Hui LIU ◽  
Gen-Liang HOU ◽  
Xun-Jia SU ◽  
Feng GUO ◽  
Zhou XIAO ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Photocatalytic Activity ◽  
Heat Treatment Temperature ◽  
Treatment Temperature ◽  
Composite Aerogels

Spin-dependent-magnetoresistance control by regulation of heat treatment temperature for magnetite nano-particle sinter

2009 ◽  
Vol 18 (12) ◽  
pp. 935-938
Author(s):  
H. Kobori ◽  
T. Asahi ◽  
Y. Yamasaki ◽  
A. Sugimura ◽  
T. Taniguchi ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Treatment Temperature ◽  
Nano Particle

scholarly journals Water Resistance and Creep Behavior of Heat-Treated Moso Bamboo Determined by the Stepped Isostress Method

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1264
Author(s):  
Teng-Chun Yang ◽  
Tung-Lin Wu ◽  
Chin-Hao Yeh
Keyword(s):  
Heat Treatment ◽  
Water Absorption ◽  
Creep Behavior ◽  
Heat Treatment Temperature ◽  
Water Resistance ◽  
Absorption Efficiency ◽  
Treatment Temperature ◽  
Moso Bamboo ◽  
Phyllostachys Pubescens ◽  
Heat Treated

The influence of heat treatment on the physico-mechanical properties, water resistance, and creep behavior of moso bamboo (Phyllostachys pubescens) was determined in this study. The results revealed that the density, moisture content, and flexural properties showed negative relationships with the heat treatment temperature, while an improvement in the dimensional stability (anti-swelling efficiency and anti-water absorption efficiency) of heat-treated samples was observed during water absorption tests. Additionally, the creep master curves of the untreated and heat-treated samples were successfully constructed using the stepped isostress method (SSM) at a series of elevated stresses. Furthermore, the SSM-predicted creep compliance curves fit well with the 90-day full-scale experimental data. When the heat treatment temperature increased to 180 °C, the degradation ratio of the creep resistance (rd) significantly increased over all periods. However, the rd of the tested bamboo decreased as the heat treatment temperature increased up to 220 °C.

Effect of Heat Treatment on the Microstructure and Property of TiAl Alloys Prepared by Gas Atomization Powders

2013 ◽  
Vol 747-748 ◽  
pp. 497-501
Author(s):  
Na Liu ◽  
Zhou Li ◽  
Guo Qing Zhang ◽  
Hua Yuan ◽  
Wen Yong Xu ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Tial Alloy ◽  
Lamellar Microstructure ◽  
Treatment Temperature ◽  
Gas Atomization ◽  
Thermally Induced ◽  
Heat Treated ◽  
Fine Duplex ◽  
Step Heat Treatment

Powder metallurgical TiAl alloy was fabricated by gas atomization powders, and the effect of heat treatment temperature on the microstructure evolution and room tensile properties of PM TiAl alloy was investigated. The uniform fine duplex microstructure was formed in PM TiAl based alloy after being heat treated at 1250/2h followed by furnace cooling (FC)+ 900/6h (FC). When the first step heat treatment temperature was improved to 1360/1h, the near lamellar microstructure was achieved. The ductility of the alloy after heat treatment improved markedly to 1.2% and 0.6%, but the tensile strength decreased to 570MPa and 600MPa compared to 655MPa of as-HIP TiAl alloy. Post heat treatment at the higher temperature in the alpha plus gamma field would regenerate thermally induced porosity (TIP).

Sign in / Sign up

Export Citation Format

Share Document