scholarly journals Water Resistance and Creep Behavior of Heat-Treated Moso Bamboo Determined by the Stepped Isostress Method

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1264
Author(s):  
Teng-Chun Yang ◽  
Tung-Lin Wu ◽  
Chin-Hao Yeh
Keyword(s):  
Heat Treatment ◽  
Water Absorption ◽  
Creep Behavior ◽  
Heat Treatment Temperature ◽  
Water Resistance ◽  
Absorption Efficiency ◽  
Treatment Temperature ◽  
Moso Bamboo ◽  
Phyllostachys Pubescens ◽  
Heat Treated

The influence of heat treatment on the physico-mechanical properties, water resistance, and creep behavior of moso bamboo (Phyllostachys pubescens) was determined in this study. The results revealed that the density, moisture content, and flexural properties showed negative relationships with the heat treatment temperature, while an improvement in the dimensional stability (anti-swelling efficiency and anti-water absorption efficiency) of heat-treated samples was observed during water absorption tests. Additionally, the creep master curves of the untreated and heat-treated samples were successfully constructed using the stepped isostress method (SSM) at a series of elevated stresses. Furthermore, the SSM-predicted creep compliance curves fit well with the 90-day full-scale experimental data. When the heat treatment temperature increased to 180 °C, the degradation ratio of the creep resistance (rd) significantly increased over all periods. However, the rd of the tested bamboo decreased as the heat treatment temperature increased up to 220 °C.

Effect of Heat Treatment on the Microstructure and Property of TiAl Alloys Prepared by Gas Atomization Powders

2013 ◽  
Vol 747-748 ◽  
pp. 497-501
Author(s):  
Na Liu ◽  
Zhou Li ◽  
Guo Qing Zhang ◽  
Hua Yuan ◽  
Wen Yong Xu ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Tial Alloy ◽  
Lamellar Microstructure ◽  
Treatment Temperature ◽  
Gas Atomization ◽  
Thermally Induced ◽  
Heat Treated ◽  
Fine Duplex ◽  
Step Heat Treatment

Powder metallurgical TiAl alloy was fabricated by gas atomization powders, and the effect of heat treatment temperature on the microstructure evolution and room tensile properties of PM TiAl alloy was investigated. The uniform fine duplex microstructure was formed in PM TiAl based alloy after being heat treated at 1250/2h followed by furnace cooling (FC)+ 900/6h (FC). When the first step heat treatment temperature was improved to 1360/1h, the near lamellar microstructure was achieved. The ductility of the alloy after heat treatment improved markedly to 1.2% and 0.6%, but the tensile strength decreased to 570MPa and 600MPa compared to 655MPa of as-HIP TiAl alloy. Post heat treatment at the higher temperature in the alpha plus gamma field would regenerate thermally induced porosity (TIP).

Mechanical and Superelastic Properties of Au-51Ti-18Co Biomedical Shape Memory Alloy Heat-Treated at 1173 K to 1373 K

2016 ◽  
Vol 97 ◽  
pp. 141-146 ◽  
Author(s):  
Taywin Buasri ◽  
Hyunbo Shim ◽  
Masaki Tahara ◽  
Tomonari Inamura ◽  
Kenji Goto ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Critical Stress ◽  
Biomedical Applications ◽  
Shape Recovery ◽  
Treatment Temperature ◽  
Recovery Ratio ◽  
Recovery Strain ◽  
Heat Treated ◽  
Alloy Heat

The effect of heat treatment temperature from 1173 K to 1373 K for 3.6 ks on mechanical and superelastic properties of an Ni-free Au-51Ti-18Co alloy (mol%) was investigated. The stress for inducing martensitic transformation (SIMT) and the critical stress for slip deformation (CSS) slightly decrease with increasing the heat–treatment temperature. Regardless of heat–treatment temperature, good superelasticity was definitely recognized with the maximum shape recovery ratio up to 95 % and 4 % superelastic shape recovery strain. As the mentioned reasons, the Au-51Ti-18Co alloy is promising for practical biomedical applications.

Investigation of Heat Treated Electrodeposited CoNiFe on Microstructure and Hardness

2015 ◽  
Vol 1113 ◽  
pp. 56-61
Author(s):  
Nor Azrina Resali ◽  
Koay Mei Hyie ◽  
M.N. Berhan ◽  
C.M. Mardziah
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Treatment Temperature ◽  
Crystallographic Structure ◽  
Face Centered Cubic ◽  
Heat Treated ◽  
Hardness Property ◽  
Finishing Process ◽  
The Face ◽  
Face Centered

In this research, heat treatment is the final finishing process applied on nanocrystalline CoNiFe to improve microstructure for good hardness property. Nanocrystalline CoNiFe has been synthesized using the electrodeposition method. This study investigated the effect of heat treatment at 500°C, 600°C, 700°C and 800°C on electrodeposited nanocrystalline CoNiFe. The heat treatment process was performed in the tube furnace with flowing Argon gas. By changing the heat treatment temperature, physical properties such as phase and crystallographic structure, surface morphology, grain size and hardness of nanocrystalline CoNiFe was studied. The nanocrystalline CoNiFe phase revealed the Face Centered Cubic (FCC) and Body Centered Cubic (BCC) crystal structure. FESEM micrographs showed that the grain sizes of the coatings were in the range of 78.76 nm to 132 nm. Dendrite shape was found in the microstructure of nanocrystalline CoNiFe. The nanocrystalline CoNiFe prepared in heat treatment temperature of 700°C, achieved the highest hardness of 449 HVN. The surface roughness of nanocrystalline CoNiFe heated at 700°C was found to be smaller than other temperatures.

Effects of Heat-Treatment Temperature on the Properties of Negative CTE Eucryptite Ceramics

2010 ◽  
Vol 105-106 ◽  
pp. 123-125 ◽  
Author(s):  
Yong Li ◽  
Qi Hong Wei ◽  
Ling Li ◽  
Chong Hai Wang ◽  
Xiao Li Zhang ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Thermal Expansion ◽  
Thermal Expansion Coefficient ◽  
Expansion Coefficient ◽  
Heat Treatment Temperature ◽  
Bending Strength ◽  
Sol Gel ◽  
Negative Thermal Expansion ◽  
Treatment Temperature ◽  
Heat Treated

In this paper, negative thermal expansion coefficient eucryptite powders were prepared by sol-gel method using silica-sol as starting material. The raw blocks were obtained by dry pressing process after the powder was synthesized, and then the raw blocks were heat-treated at 600º, 1150º, 1280º, 1380º, 1420º and 1450°C, respectively. Variations of density, porosity and thermal expansion coefficient at different heat treatment temperatures were investigated. Phase transformation and fracture surface morphology of eucryptite heat-treated at different temperatures, respectively, were observed by XRD and SEM. The results indicate that, with the increasing heat- treatment temperature, the grain size and the bending strength increased, porosity decreased, thermal expansion coefficient decreased continuously. Negative thermal expansion coefficient of -5.3162×10-6~-7.4413×10-6 (0~800°C) was obtained. But when the heat-treatment temperature was more than 1420°C, porosity began to increase, bending strength began to decrease, which were the symbols of over-burning, while the main crystal phase didn’t change.

Effect of Heat Treatment on the Combustion Characteristics of a Lignite

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Zhezi Zhang ◽  
Mingming Zhu ◽  
Jianbo Li ◽  
Kai Zhang ◽  
Guoqing Shen ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Ignition Delay ◽  
Delay Time ◽  
Heat Treatment Temperature ◽  
Ignition Delay Time ◽  
Treatment Temperature ◽  
Ftir Analysis ◽  
Single Particles ◽  
Heat Treated ◽  
Ignition And Combustion

In this study, the ignition and combustion behavior of raw and heat-treated single particles of lignite were experimentally investigated, with a focus on the effect of heat treatment temperatures. The lignite particles were heat treated to various final temperatures (473, 623 and 773 K) in nitrogen and characterized using proximate, ultimate, and Fourier transform infrared spectroscopy (FTIR) analysis. A single lignite particle of 2 or 3 mm in diameter was suspended on a silicon carbide fiber and burned in air in a horizontal tube furnace operating at 1123 K. The ignition and combustion process of the particle was record using a color CCD camera at 25 fps. The ignition mechanism, ignition delay time, volatile flame duration, and burnout time of the single particles were examined by processing the recorded images. The proximate and ultimate analysis results indicated that the volatile matter and oxygen contents decreased, while the carbon content increased with increasing temperature of heat treatment. This trend was consistent with observations in the FTIR analysis, in which the intensity of oxygen-containing functional groups decreased with increasing the heat treatment temperature. The ignition of raw and heat treated lignite particles followed a joint hetero-homogeneous mechanism under all conditions studied. The ignition delay time, volatile flame extinction time, and the total combustion time decreased with increasing heat treatment temperature up to 623 K. A further increase in the heat treatment temperature to 773 K resulted in prolonged key ignition and combustion characteristic times.

Effect of Heat Treatment on the Reactivity and Crystallinity of Coal-Char

2005 ◽  
Author(s):  
Shouyu Zhang ◽  
Junfu Lu ◽  
Jianmin Zhang ◽  
Qing Liu ◽  
Guangxi Yue
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Treatment Time ◽  
Treatment Temperature ◽  
Coal Char ◽  
Heat Treatment Time ◽  
Heat Treat ◽  
Heat Treated ◽  
Layer Stacking ◽  
Crystalline Growth

The effect of heat treatment on the reactivity and crystallinity of char prepared from the vitrinite of two coals (YX, JJ) was investigated by using XRD and TGA in this paper. The results from TGA show that the reactivity of the chars from YXV and JJV decreases with the increase of heat treatment temperature. The reactivity of YXV char decreases quickly and significantly as heat treatment time increases. However, after heat treatment time of 60 min, it decreases slowly. The effect of heat treatment time on the reactivity of JJV char is small. The results from XRD show that the crystallinity of coal-char is determined by the intensity of heat treatment. When heat treatment time is more than 60 minutes, the turbostratic crystallite of YXV char prepared under 900°C changes remarkably and becomes more orderly. The aromatic layer stacking heights (Lc) of YXV Char when heat treated above 900°C increased with the increase of heat treatment time. The effect of heat treat time on Lc of JJV char is small, but under heat treatment temperature of 1200°C, the crystalline of JJV char grows distinctly. There is a good parallel relationship between the crystalline growth and deactivation of the chars. It can be concluded that the growth of the crystalline is the main reason for the deactivation of coal-char.

Effect of Heat-Treatment Temperature on the Osteoconductivity of the Apatite Derived from Bovine Bone

2006 ◽  
Vol 309-311 ◽  
pp. 41-44 ◽  
Author(s):  
Sang Hoon Rhee ◽  
Ho Nam Park ◽  
Yang Jo Seol ◽  
Chong Pyong Chung ◽  
Sang Hyuk Han
Keyword(s):  
Heat Treatment ◽  
Physical Properties ◽  
Heat Treatment Temperature ◽  
Zealand White Rabbit ◽  
Treatment Temperature ◽  
Bovine Bone ◽  
Carbonate Ions ◽  
Heat Treated ◽  
Ft Ir ◽  
Field Emission Electron Microscopy

Effect of heat-treatment temperature on the osteoconductivity of the apatite derived from bovine trabecular bone was investigated. Three different heat-treatment temperatures (600, 800 and 1000 oC) were adopted in the experiment and their effects on the physical properties of apatite granules, which could affect on the osteoconductivity, were evaluated. The content of carbonate ions in the apatite structure was assessed by FT-IR and its crystallinity was evaluated by X-ray diffractometry. The microstructure was assessed by field emission electron microscopy. Apatite granules heat-treated at 600 oC and 1000 oC were implanted into the calvaria of New Zealand White rabbit for 4 weeks, respectively, and the undecalcified ground histologic specimens stained with multiple staining method was observed. As increasing the heat-treatment temperature, the crystal size and crystallinity of the apatite increased while the content of carbonate ions decreased. The apatite granules heat-treated at 600 oC showed much better osteoconductivity comparing to that heat-treated at 1000 oC. The results were explained in terms of the physical properties of apatite which could affect to the osteoconductivity.

Phase Separation in Alumina-Chromia

2002 ◽  
Vol 731 ◽  
Author(s):  
M. S. McIntosh ◽  
T. H. Sanders ◽  
J. M. Hampikian
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Treatment Temperature ◽  
Miscibility Gap ◽  
Mole Percent ◽  
Tem Analysis ◽  
X Ray ◽  
Heat Treated ◽  
Solution Models ◽  
Liquid And Solid Phases

AbstractThe alumina-chromia system shows complete mutual solubility and is represented by an isomorphous phase diagram. However, the alumina-chromia system exhibits an asymmetric miscibility gap under 1300°C. Using existing data from the literature, the alumina-chromia system was assessed using thermodynamic modeling by Kim and Sanders [1]. Regular and subregular solution models for the liquid and solid phases were used to define the phase boundaries for the miscibility gap in this system. Using this thermodynamic representation of the miscibility gap to select temperatures of interest, 75 mole percent Al2O3samples were synthesized via combustion of powders, followed by pressing into pellets and heat-treated for various times and temperatures. Both X-ray and TEM analysis showed evidence of spinodal decomposition after heat-treatment. X-ray analysis showed that decreasing the heat-treatment temperature increases the compositional difference between the phases present. The experimentally observed microstructures exhibit lamella-like structures that vary in spacing from 8nm to 3nm as the heat-treatment temperature varies from 400°C to 800°C.

scholarly journals Investigation of intercritical heat treatment temperature effect on microstructure and mechanical properties of dual phase (DP) steel

10.30544/293 ◽  
2017 ◽  
Vol 23 (2) ◽  
pp. 143-152
Author(s):  
Mohammad Davari ◽  
Mehdi Mansouri Hasan Abadi
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Work Hardening ◽  
Heat Treatment Temperature ◽  
Treatment Temperature ◽  
Dual Phase ◽  
Work Hardening Behavior ◽  
Hardening Behavior ◽  
Heat Treated ◽  
Intercritical Heat Treatment

In the present study, the effect of intercritical heat treatment temperature on the tensile properties and work hardening behavior of ferritic-martensitic dual-phase steel have been investigated utilizing tensile test, microhardness measurement and microscopic observation. Plain carbon steel sheet with a thickness of 2 mm was heat treated at 760, 780, 800, 820 and 840 °C intercritical temperatures. The results showed that martensite volume fraction (Vm) increases from 32 to 81%with increasing temperature from 760 to 840 °C. The mechanical properties of samples were examined by tensile and microhardness tests. The results revealed that yield strength was increased linearly with the increase in Vm, but the ultimate strength was increased up to 55% Vm and then decreased afterward. Analyzing the work hardening behavior in term of Hollomon equation showed that in samples with less than 55% Vm, the work hardening took place in one stage and the work hardening exponent increased with increasing Vm. More than one stage was observed in the work hardening behavior when Vm was increased. The results of microhardness test showed that microhardness of the martensite is decreased by increase in heat treatment temperature while the ferrite microhardness is nearly constant for all heat-treated samples.

Tribological Behavior of Electroless Ni-P, Ni-P-W and Ni-P-Cu Coatings

2017 ◽  
Vol 5 (1) ◽  
pp. 1-15 ◽  
Author(s):  
Prasanta Sahoo ◽  
Supriyo Roy
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Tribological Behavior ◽  
Treatment Temperature ◽  
Chemical Compositions ◽  
Heat Treated ◽  
Tungsten Concentration ◽  
The Comparative Study ◽  
Main Effects ◽  
Electroless Ni

The present paper considers the comparative study of tribological characteristics of various electroless alloy coatings viz. Ni-P, Ni-P-W and Ni-P-Cu. The tribological behavior of these coatings depends on various parameters like load, speed, lubricant, chemical compositions and heat treatment temperature to a great extent. One of the main effects of heat treatment on these coatings is phosphide precipitation, which makes them suitable for anti-wear applications. The property of binary Ni-P can be further improved by depositing third particles electrolessly. The phase structure of the coatings depends on the amount of phosphorous and heat treatment temperature. The tribological behavior of heat treated samples reveals that Ni-P-W deposit shows higher coefficient of friction and lowest wear among these three types coatings. Very high tungsten concentration retard the phosphide precipitation, thus low concentration of tungsten and low heat treatment temperature produce better coating. In case of Ni-P-Cu, medium concentration of copper and medium heat treatment temperature produces better coating.

Sign in / Sign up

Export Citation Format

Share Document