scholarly journals A Numerical Study on Thermal Elastohydrodynamic Lubrication of Coated Polymers

2020 ◽  
Vol 68 (2) ◽  
Author(s):  
A. Ziegltrum ◽  
E. Maier ◽  
T. Lohner ◽  
K. Stahl
Keyword(s):  
Numerical Study ◽  
Elastohydrodynamic Lubrication

Experimental and numerical study on cavitation under elastohydrodynamic lubrication point contact

2021 ◽  
pp. 135065012110527
Author(s):  
Mingfei Ma ◽  
Wen Wang ◽  
Wenxun Jiang
Keyword(s):  
Contact Area ◽  
Numerical Study ◽  
Ambient Pressure ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Hertzian Contact ◽  
Pressure Area ◽  
Cavitation Pressure ◽  
Experimental Researches ◽  
State 1

As a common phenomenon in elastohydrodynamic lubrication, cavitation has an effect on the completeness of the oil film in the contact area. Many studies have therefore been conducted on cavitation. Experimental researches on cavitation usually rely on optical interference observation, which offers a limited resolution and observation range. In this paper, an infrared thermal camera is used to observe the cavity bubbles on a ball-on-disc setup under sliding/rolling conditions. The results show that the cavity length increases with an increases of the entrainment speed and the viscosity of the lubricants. These observations are explained by a numerical model based on Elrod's algorithm. Effects of entrainment speed and lubricant viscosity on the breakup of cavitation bubbles and the cavitation states are investigated. Both the simulation and experimental results show that a negative pressure area is present behind the Hertzian contact area. The ambient pressure plays a role in maintaining cavitation state 1. The cavitation pressure is close to the vacuum pressure when the entrainment speed is low and to the ambient pressure instead when the entrainment speed is high.

Numerical Study of Piston Skirt-Liner Elastohydrodynamic Lubrication and Contact by the Multigrid Method

2010 ◽  
Author(s):  
Xianghui Meng ◽  
Youbai Xie
Keyword(s):  
Contact Problem ◽  
Internal Combustion Engines ◽  
Multigrid Method ◽  
Numerical Study ◽  
Elastohydrodynamic Lubrication ◽  
Cylinder Liner ◽  
Piston Skirt ◽  
Liner System ◽  
Tribological Analysis ◽  
Quasi Newton

The cylinder liner-piston system of internal combustion engines is one of the key friction pairs running at the most rigor working conditions. Under the influence of elastohydrodynamic lubrication and contact between the piston skirt and the liner, the dynamic process of piston is a nonlinear and stiff problem difficult to be analyzed accurately and easily. To reach a stable and rapid convergence in analysis, the MEBDF method and the multigrid method are used to solve the piston-skirt elastohydrodynamic lubrication and contact problem. Firstly the solving process of the piston dynamics is analyzed based on the MEBDF method. Then the residual equations for the elastohydrodynamic lubrication pressure are built based on the multigrid method. And the solving method of the nonlinear residual equations is presented based on the quasi Newton-Raphson method. Finally the numerical simulation program is developed based on the MEBDF method and the multigrid method. The elastohydrodynamic lubrication and contact problem of the piston skirt-liner system is simply analyzed based on the simulation. The study in this paper can provide an effective method for tribological analysis and optimization of piston–liner system in the future.

Numerical study on the interaction of transversely oriented ridges in thermal elastohydrodynamic lubrication point contacts using the Eyring shear-thinning model

2016 ◽  
Vol 231 (1) ◽  
pp. 93-106 ◽  
Author(s):  
Jinlei Cui ◽  
Peiran Yang ◽  
Motohiro Kaneta ◽  
Ivan Krupka
Keyword(s):  
Friction Coefficient ◽  
Numerical Study ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Shear Thinning ◽  
Solid Surfaces ◽  
Point Contacts ◽  
Transient Behaviour ◽  
Contact Surfaces ◽  
Thinning Effect

Transient behaviour of tribo-characteristics caused by transversely oriented ridges on point contact surfaces was investigated based on a thermal elastohydrodynamic lubrication analysis. The ridges were assumed to exist on both the contact surfaces with different velocities. Results show that the interaction of ridges gives a large influence on the local film thickness, pressure, friction coefficient, temperatures on both the solid surfaces and temperature in the oil film. It is also pointed out that the size of the contact bodies brings strong effect on the temperature distribution and shear rate as well as on the friction coefficient. Furthermore, it is revealed that under rolling-sliding conditions, the shear-thinning property of the lubricant is negligible when the size of the contact body is large enough. However, shear-thinning effect plays an important role when the size is extremely small.

Three-Dimensional Temperature Distribution in EHD Lubrication: Part II—Point Contact and Numerical Formulation

1993 ◽  
Vol 115 (1) ◽  
pp. 36-45 ◽  
Author(s):  
Kyung-Hoon Kim ◽  
Farshid Sadeghi
Keyword(s):  
Temperature Distribution ◽  
Film Thickness ◽  
Numerical Study ◽  
Control Volume ◽  
Three Dimensional ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Lubricant Film ◽  
Numerical Formulation ◽  
Energy Equations

A numerical study of Newtonian thermal elastohydrodynamic lubrication (EHD) of rolling/sliding point contacts has been conducted. The two-dimensional Reynolds, elasticity and the three-dimensional energy equations were solved simultaneously to obtain the pressure, film thickness and temperature distribution within the lubricant film. The control volume approach was employed to discretize the differential equations and the multi-level multi-grid technique was used to simultaneously solve them. The discretized equations, as well as the nonorthogonal coordinate transformation used for the solution of the energy equation, are described. The pressure, film thickness and the temperature distributions, within the lubricant film at different loads, slip conditions and ellipticity parameters are presented.

Thermal Elastohydrodynamic Lubrication of Axially Crowned Rollers

2021 ◽  
pp. 1-21
Author(s):  
Wassim Habchi
Keyword(s):  
Film Thickness ◽  
Design Parameter ◽  
Numerical Study ◽  
Elastohydrodynamic Lubrication ◽  
Negative Influence ◽  
Reference Case ◽  
Critical Design ◽  
Lubrication Performance ◽  
Minimum Film Thickness ◽  
Line Contacts

Abstract This work presents a comprehensive numerical study of thermal elastohydrodynamic lubrication performance in axially crowned rollers, based on a full-system finite element approach. Axial crowning has always been introduced to finite line contacts, as a mean for improving film thickness. Its influence on friction has often been overlooked though. The current work reveals that axial crowning has a negative influence on friction, increasing it significantly with respect to the reference case of straight rollers. It is shown that, with increased crowning height (or reduced crowning radius), minimum film thickness is increased, but so is friction. Therefore, film thickness enhancement comes at the expense of a deterioration in friction. Besides, achieving sufficient enhancements in minimum film thickness would require using relatively low crowning radii, which would lead to a substantial increase in friction. The frictional increase is traced back to an overall increase in contact pressures and effective contact area within the lubricating conjunction. It is also shown that, when film thickness is the most critical design parameter, the best compromise between enhanced film thickness and deteriorated friction would be to combine axial crowning with roller-end profiling. However, when friction is the most critical design parameter, a simple roller-end profiling would offer the best compromise.

Numerical study of surface dimple phenomenon by starvation in simple sliding contact

2017 ◽  
Vol 69 (6) ◽  
pp. 980-989 ◽  
Author(s):  
Shun Cui ◽  
Hiroshi Nishikawa ◽  
Jing Wang ◽  
Qian Zou
Keyword(s):  
Flow Model ◽  
Numerical Study ◽  
Elastohydrodynamic Lubrication ◽  
Content Type ◽  
Sliding Motion ◽  
Starvation Condition ◽  
Pressure Peak ◽  
Oil Replenishment ◽  
Circular Contact ◽  
Ehl Contact

Purpose This study aims to use a thermal elastohydrodynamic lubrication (EHL) algorithm incorporating an Eyring flow model to solve a steady-state contact in simple sliding motion. Design/methodology/approach A theoretical model was used to investigate the effect of starvation on the surface dimple phenomenon by gradually reducing the thickness of the inlet oil layer. Findings The increase in the starvation degree reduces the dimple depth, film thickness, the pressure peak and the temperature rise. Under the severe starvation condition, the dimple is eliminated so that the EHL contact becomes partly parched. In elliptical results, for the same starvation parameters, the oil replenishment is stronger than that in circular contact. Originality/value This paper fulfils an exploration to study how the oil starvation influences the surface dimple phenomenon.

Sign in / Sign up

Export Citation Format

Share Document