Low speed axial compressor stall margin improvement by unsteady plasma actuation

2014 ◽  
Vol 23 (2) ◽  
pp. 114-119 ◽  
Author(s):  
Gang Li ◽  
Yanji Xu ◽  
Lingyuan Yang ◽  
Wei Du ◽  
Junqiang Zhu ◽  
...  
Keyword(s):  
Axial Compressor ◽  
Stall Margin ◽  
Low Speed ◽  
Plasma Actuation ◽  
Stall Margin Improvement

scholarly journals Stall margin improvement in a low-speed axial compressor rotor using a blockage-optimised single circumferential casing groove

2021 ◽  
Vol 5 ◽  
pp. 79-89
Author(s):  
Ahmad Fikri Mustaffa ◽  
Vasudevan Kanjirakkad
Keyword(s):  
Axial Compressor ◽  
Pressure Rise ◽  
Leading Edge ◽  
Tip Leakage Flow ◽  
Stall Margin ◽  
Low Speed ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Stall Margin Improvement ◽  
Edge Based

The stall margin of tip-critical axial compressors can be improved by using circumferential casing grooves. From previous studies, in the literature, the stall margin improvement due to the casing grooves can be attributed to the reduction of the near casing blockage. The pressure rise across the compressor as the compressor is throttled intensifies the tip leakage flow. This results in a stronger tip leakage vortex that is thought to be the main source of the blockage. In this paper, the near casing blockage due to the tip region aerodynamics in a low-speed axial compressor rotor is numerically studied and quantified using a mass flow-based blockage parameter. The peak blockage location at the last stable operating point for a rotor with smooth casing is found to be at about 10% of the tip chord aft of the tip leading edge. Based on this information, an optimised single casing groove design that minimises the peak blockage is found using a surrogate-based optimisation approach. The implementation of the optimised groove is shown to produce a stall margin improvement of about 5%.

scholarly journals Effects of Endwall Suction and Blowing on Compressor Stability Enhancement

1989 ◽  
Author(s):  
N. K. W. Lee ◽  
E. M. Greitzer
Keyword(s):  
Flow Injection ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Primary Objective ◽  
Stall Margin ◽  
Casing Treatment ◽  
Blade Row ◽  
Stall Margin Improvement ◽  
Stability Enhancement ◽  
Suction And Blowing

An experimental investigation was carried out to examine the effects on stall margin of flow injection into, and flow removal out of, the endwall region of an axial compressor blade row. A primary objective of the investigation was clarification of the mechanism by which casing treatment (which involves both removal and injection) suppresses stall in turbomachines. To simulate the relative motion between blade and treatment, the injection and removal took place through a slotted hub rotating beneath a cantilevered stator row. Overall performance data and detailed (time-averaged) flowfield measurements were obtained. Flow injection and removal both increased the stalling pressure rise, but neither was as effective as the wall treatment. Removal of high blockage flow is thus not the sole reason for the observed stall margin improvement in casing or hub treatment, as injection can also contribute significantly to stall suppression. The results also indicate that the increase in stall pressure rise with injection is linked to the streamwise momentum of the injected flow, and it is suggested that this should be the focus of further studies.

Tip Leakage Vortex Control in a Low Speed Axial Compressor Using Pulsed Plasma Actuation

2016 ◽  
Author(s):  
Yun Wu ◽  
Cai-dong Ma ◽  
Si-meng Tian ◽  
You-tian Zhou ◽  
Jun Li ◽  
...  
Keyword(s):  
Axial Compressor ◽  
Pulsed Plasma ◽  
Tip Leakage Flow ◽  
Control Effect ◽  
Stability Range ◽  
Tip Leakage Vortex ◽  
Low Speed ◽  
Tip Leakage ◽  
Vortex Control ◽  
Plasma Actuation

Plasma actuation is a novel method for axial compressor flow control with advantages of short response time and broad frequency range. Numerical simulation of tip leakage vortex control in a low speed axial compressor with pulsed plasma actuation is performed. Millisecond pulsed dielectric barrier discharge plasma actuation with different frequencies are generated on the inner wall of compressor casing at the rotor leading edge. Scale adaptive hybrid Reynolds-averaged Navier-Stokes/large eddy simulation method based on shear stress transport turbulence model is adopted. The plasma actuation is simplified as a body force in the simulation. Results show that the frequency has a strong influence on the control effect of pulsed plasma actuation. Pulsed plasma actuation with frequency of 0.25 blade passing frequency (BPF), 0.5 BPF and 1.0 BPF extend the compressor’s stability range effectively. The mechanism is tip leakage vortex oscillation in the stream wise direction through coupling between unsteady plasma actuation and tip leakage flow. However, pulsed plasma actuation with frequency of 0.125 BPF, 2 BPF and 3 BPF fails to improve the stability range. The mechanism of pulsed plasma actuation at 2 BPF and 3 BPF is similar to that with steady plasma actuation, which is only stream wise boundary layer acceleration. The oscillation of tip leakage vortex in the stream wise direction can’t occur. For the pulsed plasma actuation at 0.125 BPF, its frequency is too low to get enough control effect.

Experimental and Numerical Investigation of Effect of Center Offset Degree on Compressor Stability With Circumferential Grooved Casing Treatment

2016 ◽  
Author(s):  
HaoGuang Zhang ◽  
Feng Tan ◽  
YanHui Wu ◽  
WuLi Chu ◽  
Wei Wang ◽  
...  
Keyword(s):  
Axial Compressor ◽  
Leading Edge ◽  
Groove Depth ◽  
Tip Clearance ◽  
Central Difference ◽  
Stall Margin ◽  
Casing Treatment ◽  
Compressor Rotor ◽  
Stall Margin Improvement ◽  
Blade Tip

For compressor blade tip stall, one effective way of extending stable operating range is with the application of circumferential grooved casing treatment and its validity was proved by a lot of experimental and numerical investigations. The emphases of most circumferential grooved investigations are focused on the influence of groove depth and groove number on compressor stability, and there is few investigations dealt with the center offset degree of circumferential grooves casing treatment. Hence, an axial compressor rotor with casing treatment (CT) was investigated with experimental and numerical methods to explore the effect of center offset degree on compressor stability and performance. In the work reported here, The center offset degree is defined as the ratio of the central difference between rotor tip axial chord and CT to the axial chord length of rotor tip. When the center of CT is located within the upstream direction of the center of rotor tip axial chord, the value of center offset degree is positive. The experimental and numerical results show that stall margin improvement gained with CT is reduced as the value of center offset degree varies from 0 to 0.33 or −0.33, and the CT with −0.33 center offset degree achieves the lowest value of stall margin improvement at 53% and 73% design rotational speed. The detailed analysis of the flow-field in compressor tip indicates that there is not positive effect made by grooves on leading edge of rotor blade tip when the value of center offset degree is −0.33. As the mass flow of compressor reduces further, tip clearance leakage flow results in the outlet blockage due to the absence of the positive action of grooves near blade tip tail when the value of center offset degree is 0.33. Blockage does not appear in rotor tip passage owing to utilizing the function of all grooves with CT of 0 center offset degree.

Numerical Investigation on Slot Casing Treatment in a Transonic Axial Compressor Stage: Part 1 — Casing Treatment Design

2016 ◽  
Author(s):  
Mingmin Zhu ◽  
Xiaoqing Qiang ◽  
Jinfang Teng
Keyword(s):  
Axial Compressor ◽  
Leakage Flow ◽  
Compressor Stage ◽  
Tip Leakage Flow ◽  
Suction Surface ◽  
Stall Margin ◽  
Rotating Speed ◽  
Casing Treatment ◽  
Tip Leakage ◽  
Stall Margin Improvement

Slot-type casing treatment generally has a great potential of enhancing the operating range for tip-critical compressor rotors, however, with remarkable efficiency drop. Part I of this two-part paper was committed to develop a slot configuration with desired stall margin improvement and minimized efficiency loss. Steady simulation was carried out in a 1.5 transonic axial compressor stage at part design rotating speed. At this rotating speed this compressor stage operated at a subsonic condition and showed a rather narrow operating range, which needed to be improved badly. Flow fields analysis at peak efficiency and near stall point showed that the development of tip leakage vortex and resulting blockage near casing resulted in numerical stall. Three kinds of skewed slots with same rotor exposure and casing porosity were designed according to the tip flow field and some empirical strategies. Among three configurations, arc-curved skewed slot showed minimum peak efficiency drop with considerable stall margin improvement. Then rotor exposure and casing porosity were varied based on the original arc-curved skewed slot, with a special interest in detecting their impact on the compressor stability and overall efficiency. Result showed that smaller rotor exposure and casing porosity leaded to less efficiency drop. But meanwhile, effectiveness of improving compressor stability was weakened. The relation between efficiency drop and stall margin improvement fell on a smooth continuous curve throughout all slots configurations, indicating that the detrimental effect of casing treatment on compressor was inevitable. Flow analysis was carried out for cases of smooth casing and three arc-curved configurations at smooth casing near stall condition. The strength of suction/injection, tip leakage flow behavior and removal of blockage near casing were detailed examined. Larger rotor tip exposure and slots number contributed to stronger injection flow. The loss generated within the mixing process of injection flow with main flow and leakage flow is the largest source of entropy increase. Further loss mechanisms were interpreted at eight axial cuts, which were taken through the blade row and slots to show the increase in entropy near tip region. Entropy distributions manifested that loss generations with smooth casing were primarily ascribed to low-momentum tip leakage flow/vortex and suction surface separation at leading edge. CU0 slot, the arc-curved slots with 50% rotor tip exposure, was capable of suppressing the suction surface separation loss. Meanwhile, accelerated tip leakage flow brought about additional loss near casing and pressure surface. Upstream high entropy flow would be absorbed into the rear portion of slots repeatedly, resulting in further loss.

Effects of Endwall Suction and Blowing on Compressor Stability Enhancement

1990 ◽  
Vol 112 (1) ◽  
pp. 133-144 ◽  
Author(s):  
N. K. W. Lee ◽  
E. M. Greitzer
Keyword(s):  
Flow Injection ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Primary Objective ◽  
Stall Margin ◽  
Casing Treatment ◽  
Blade Row ◽  
Stall Margin Improvement ◽  
Stability Enhancement ◽  
Suction And Blowing

An experimental investigation was carried out to examine the effects on stall margin of flow injection into, and flow removal out of, the endwall region of an axial compressor blade row. A primary objective of the investigation was to clarify the mechanism by which casing treatment (which involves both removal and injection) suppresses stall in turbomachines. To simulate the relative motion between blade and treatment, the injection and removal took place through a slotted hub rotating beneath a cantilevered stator row. Overall performance data and detailed (time-averaged) flowfield measurements were obtained. Flow injection and removal both increased the stalling pressure rise, but neither was as effective as the wall treatment. Removal of high-blockage flow is thus not the sole reason for the observed stall margin improvement in casing or hub treatment; injection can also contribute significantly to stall suppression. The results indicate that the increase in stall pressure rise achieved with injection is linked to the streamwise momentum of the injected flow, and it is suggested that this should be the focus of further studies.

Experimental Investigation on the Plasma Flow Control of Axial Compressor Rotating Stall

2019 ◽  
Author(s):  
Haideng Zhang ◽  
Yun Wu ◽  
Xianjun Yu ◽  
Yinghong Li ◽  
Baojie Liu
Keyword(s):  
Experimental Investigation ◽  
Plasma Flow ◽  
Body Force ◽  
Static Pressure ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Rotating Stall ◽  
Stall Margin ◽  
Plasma Actuation ◽  
Plasma Flow Control

Abstract Experimental investigation on the plasma flow control of axial compressor rotating stall is implemented in this paper. The control effects of axial plasma actuation (inducing body force of compressor axial direction) with three different locations as well as stagger angle plasma actuation (inducing body force perpendicular to the compressor rotor tip chordwise direction) at different rotation speeds are studied. An unsteady plasma actuation is designed to influence the unsteady rotor tip flow at near stall point, and is found to be the most powerful in improving the compressor stall margin. Both the compressor rotation speed and the plasma actuation voltage are found to be very influential on the control effects of the plasma actuation. The abilities of the plasma actuation in suppressing the compressor rotating stall and influencing the compressor static pressure rise coefficient are not directly related. All the plasma actuations studied can improve the compressor stall margin, but the compressor static pressure rise coefficient can be decreased or increased with different plasma actuation layouts.

Stall Margin Improvement by Casing Treatment—Its Mechanism and Effectiveness

1977 ◽  
Vol 99 (1) ◽  
pp. 121-133 ◽  
Author(s):  
H. Takata ◽  
Y. Tsukuda
Keyword(s):  
Axial Flow ◽  
Stall Margin ◽  
Low Speed ◽  
Casing Treatment ◽  
Blade Row ◽  
Stall Margin Improvement ◽  
Flow Through ◽  
Compressor Performance ◽  
Axial Flow Compressors

Experiments on the effect of casing treatment were carried out using low-speed axial-flow compressors. Results on the overall compressor performance and on the flow through the blade row as well as the flow within the treatment slots are presented. Then, based on the experiments, a possible mechanism of the stall margin improvement is suggested.

Sign in / Sign up

Export Citation Format

Share Document