Numerical analysis of rotating stall characteristics in vaneless diffuser with large width-radius ratio

2008 ◽  
Vol 2 (4) ◽  
pp. 457-460 ◽  
Author(s):  
Chuang Gao ◽  
Chuangang Gu ◽  
Tong Wang ◽  
Zhengyuan Dai
Keyword(s):  
Numerical Analysis ◽  
Rotating Stall ◽  
Radius Ratio ◽  
Vaneless Diffuser ◽  
Large Width

Experimental Characterization of Vaneless Diffuser Rotating Stall: Part VI — Reduction of Three Impeller Results

2006 ◽  
Author(s):  
E. A. Carnevale ◽  
G. Ferrara ◽  
L. Ferrari ◽  
L. Baldassarre
Keyword(s):  
Rotating Stall ◽  
Radius Ratio ◽  
Vaneless Diffuser ◽  
Cross Sectional ◽  
Stall Inception ◽  
Return Channel ◽  
Geometrical Scale ◽  
And Diffusion ◽  
Basic Configuration

Vaneless diffuser rotating stall is a major problem for centrifugal compressors since it is a limit to their working range. In the literature some good correlations for predicting stall inception can be found but they do not adequately cover the case of the last stage configuration, especially for very low blade-outlet-width-to-impeller-radius-ratio impellers typically used in high-pressure applications. Extensive research has been performed to define diffuser stall limits for this family of stages: three impellers characterized by different blade-outlet-width-to-impeller-radius-ratios have been tested with different diffuser configurations (different pinch shapes, diffuser widths and diffusion ratios). The basic configuration comprises a 1:1 geometrical scale stage with a return channel upstream, a 2D impeller with a vaneless diffuser and a volute with a constant cross sectional area downstream. Several diffuser types with different widths and diffusion ratios were tested. Detailed experimental results have been reported in previous works [1, 2, 3 and 4]. In this paper experimental data are reviewed in order to analyze impeller influence on diffuser stability and to develop some summarizing consideration on stall behavior of vaneless diffuser for impeller with low blade-outlet-width-to-impeller-radius-ratio.

scholarly journals The Effects of Diffuser Geometry on Rotating Stall Behavior

1988 ◽  
Author(s):  
M. V. Otugen ◽  
R. M. C. So ◽  
B. C. Hwang
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Critical Mass ◽  
Rotating Stall ◽  
Radius Ratio ◽  
Impeller Speed ◽  
Vaneless Diffuser ◽  
Room Condition ◽  
Inlet Opening

Experiments were carried out in a model vaneless diffuser rig to investigate the rotating stall phenomenon and its relation to diffuser geometry. The experimental rig consisted of an actual impeller which was used to deliver the flow to the vaneless diffuser. Mass flow rate through the system could be adjusted by varying the rotational speed of the impeller at a fixed inlet opening or by changing the inlet opening at a fixed impeller speed. The flow exited to room condition. As such, the rig was designed to investigate the fluid mechanics of vaneless diffuser rotating stall only. Attention was focused on the effects of diffuser width and radius on rotating stall. Three diffuser widths and three outlet radii were examined. The width-to-inlet radius ratio varied between 0.09 and 0.142 while the outlet-to-inlet radius ratio varied between 1.5 and 2. Results showed that the critical mass flow rate for the onset of rotating stall decreases with decreasing diffuser width. The critical mass flow rate is affected also by the diffuser radius ratio; larger radius ratios resulted in smaller critical mass flow rates. The ratio of the speed of rotation of the stall cell to impeller speed is found to decrease with increasing number of stall cells. This relative speed also decreases with increasing diffuser radius ratio, but it is largely independent of the diffuser width.

Experimental Investigation and Characterization of the Rotating Stall in a High Pressure Centrifugal Compressor: Part IV — Impeller Influence on Diffuser Stability

2003 ◽  
Author(s):  
A. Cellai ◽  
G. Ferrara ◽  
L. Ferrari ◽  
C. P. Mengoni ◽  
L. Baldassarre
Keyword(s):  
Experimental Investigation ◽  
High Pressure ◽  
Centrifugal Compressor ◽  
Rotating Stall ◽  
Radius Ratio ◽  
Vaneless Diffuser ◽  
Stall Inception ◽  
Last Stage ◽  
And Diffusion

Vaneless diffuser rotating stall is a major problem for centrifugal compressors since it is a limit to their working range. In particular the last stage seems to be the most critical. In the literature some good correlations for predicting stall inception can be found but they do not adequately cover the case of the last stage configuration, especially for very low blade-outlet-width-to-impeller-radius-ratio impellers typically used in high-pressure applications. Extensive research has been performed to define diffuser stall limits for this family of stages: three impellers characterized by different blade-outlet-width-to-impeller-radius-ratios are tested with different diffuser configurations (different pinch shapes, diffuser widths and diffusion ratios). Part I and II report the results of these geometry modifications on diffuser stability for the first impeller. Part III, those for the second impeller. In this part the comparison of these results in terms of impeller influence on diffuser stability is reported.

scholarly journals Rotating Stall in Vaneless Diffuser of Large Radius Ratio.

1995 ◽  
Vol 61 (591) ◽  
pp. 3842-3847
Author(s):  
Jun Matsui ◽  
Junichi Kurokawa ◽  
Michiharu Mino ◽  
Eiji Hiroki ◽  
Takaya Kitahora
Keyword(s):  
Rotating Stall ◽  
Radius Ratio ◽  
Large Radius ◽  
Vaneless Diffuser

Experimental Characterization of Vaneless Diffuser Rotating Stall: Part V — Influence of Diffuser Geometry on Stall Inception and Performance (3rd Impeller Tested)

2006 ◽  
Author(s):  
G. Ferrara ◽  
L. Ferrari ◽  
L. Baldassarre
Keyword(s):  
Rotating Stall ◽  
Radius Ratio ◽  
Vaneless Diffuser ◽  
Cross Sectional ◽  
Stall Inception ◽  
Wide Range ◽  
Return Channel ◽  
And Performance ◽  
Geometrical Scale ◽  
Performance Results

Vaneless diffuser rotating stall is a serious problem for centrifugal compressors, since it limits their working range. In the literature some good correlations can be found for predicting stall inception but they have limited coverage of last stage configuration case, especially for very low blade-outlet-width-to-impeller-radius-ratio impellers typically used in high-pressure applications. In addition, stall inception is strictly bounded to diffuser geometry (for example, diffuser width and diffusion ratio). As a part of a wide range activity on rotating stall, a stage with a blade-outlet-width-to-impeller-radius-ratio of 0.1 has been tested. The stage configuration is made up by a 1:1 geometrical scale stage with a return channel upstream, a 2D impeller with a vaneless diffuser and a volute with a constant cross sectional area downstream. Diffusers with three different widths and two diffusion ratios were tested in order to find their influence on stage stability and performance. Results obtained for impellers with lower blade-outlet-width-to-impeller-radius-ratios have been published in previous papers. The purpose of this paper is to comment the obtained results and increase the amount of experimental data available on vaneless diffuser rotating stall behaviour.

Effects of Non-Axisymmetric Volute on Rotating Stall in the Vaneless Diffuser of a Centrifugal Compressor

2020 ◽  
Author(s):  
Zitian Niu ◽  
Zhenzhong Sun ◽  
Baotong Wang ◽  
Xinqian Zheng
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Centrifugal Compressor ◽  
Stability Boundary ◽  
Rotating Stall ◽  
Evolution Process ◽  
Vaneless Diffuser ◽  
Unstable Flow ◽  
Centrifugal Compressors ◽  
Specific Location

Abstract Rotating stall is an important unstable flow phenomenon that leads to performance degradation and limits the stability boundary in centrifugal compressors. The volute is one of the sources to induce the non-axisymmetric flow in a centrifugal compressor, which has an important effect on the performance of compressors. However, the influence of volute on rotating stall is not clear. Therefore, the effects of volute on rotating stall by experimental and numerical simulation have been explored in this paper. It’s shown that one rotating stall cell generates in a specific location and disappears in another specific location of the vaneless diffuser as a result of the distorted flow field caused by the volute. Also, the cells cannot stably rotate in a whole circle. The frequency related to rotating stall captured in the experiment is 43.9% of the impeller passing frequency (IPF), while it is 44.7% of IPF captured by three-dimensional unsteady numerical simulation, which proves the accuracy of the numerical method in this study. The numerical simulation further reveals that the stall cell initialized in a specific location can be split into several cells during the evolution process. The reason for this is that the blockage in the vaneless diffuser induced by rotating stall is weakened by the mainstream from the impeller exit to make one initialized cell disperse into several ones. The volute has an important influence on the generation and evolution process of the rotating stall cells of compressors. By optimizing volute geometry to reduce the distortion of the flow field, it is expected that rotating stall can be weakened or suppressed, which is helpful to widen the operating range of centrifugal compressors.

Flow Behavior of a Centrifugal Compressor With Vaneless Diffuser at Design and Off Design Conditions

2012 ◽  
Author(s):  
Chuang Gao ◽  
Weiguang Huang ◽  
Haiqing Liu ◽  
Hongwu Zhang ◽  
Jundang Shi
Keyword(s):  
Centrifugal Compressor ◽  
Flow Behavior ◽  
Travelling Waves ◽  
Leading Edge ◽  
Pressure Oscillation ◽  
Rotating Stall ◽  
Vaneless Diffuser ◽  
Unstable Flow ◽  
Flow Recirculation ◽  
Static Performance

This paper concerns with the numerical and experimental aspects of both steady and unsteady flow behavior in a centrifugal compressor with vaneless diffuser and downstream collector. Specifically, the appearance of flow instabilities i.e., rotating stall and surge is investigated in great detail. As the first step, the static performance of both stage and component was analyzed and possible root cause of system surge was put forward based on the classic stability theory. Then the unsteady pressure data was utilized to find rotating stall and surge in frequency domain which could be classified as mild surge and deep surge. With the circumferentially installed transducers at impeller inlet, backward travelling waves during stall ramp could be observed. The modes of stall waves could be clearly identified which is caused by impeller leading edge flow recirculation at Mu = 0.96. However, for the unstable flow at Mu = 1.08, the system instability seems to be caused by reversal flow in vaneless diffuser where the pressure oscillation was strongest. Thus steady numerical simulation were performed and validated with the experimental performance data. With the help of numerical analysis, the conjectures are proved.

Study of Vaneless Diffuser Rotating Stall Based on Two-Dimensional Inviscid Flow Analysis

1996 ◽  
Vol 118 (1) ◽  
pp. 123-127 ◽  
Author(s):  
Yoshinobu Tsujimoto ◽  
Yoshiki Yoshida ◽  
Yasumasa Mori
Keyword(s):  
Propagation Velocity ◽  
Flow Instability ◽  
Present Report ◽  
Inviscid Flow ◽  
Rotating Stall ◽  
Critical Flow ◽  
Two Dimensional ◽  
Vaneless Diffuser ◽  
Flow Angle ◽  
Pressure Disturbance

Rotating stalls in vaneless diffusers are studied from the viewpoint that they are basically two-dimensional inviscid flow instability under the boundary conditions of vanishing velocity disturbance at the diffuser inlet and of vanishing pressure disturbance at the diffuser outlet. The linear analysis in the present report shows that the critical flow angle and the propagation velocity are functions of only the diffuser radius ratio. It is shown that the present analysis can reproduce most of the general characteristics observed in experiments: critical flow angle, propagation velocity, velocity, and pressure disturbance fields. It is shown that the vanishing velocity disturbance at the diffuser inlet is caused by the nature of impellers as a “resistance” and an “inertial resistance,” which is generally strong enough to suppress the velocity disturbance at the diffuser inlet. This explains the general experimental observations that vaneless diffuser rotating stalls are not largely affected by the impeller.

scholarly journals Rotating Stall in Centrifugal Compressor Vaneless Diffuser: Experimental Analysis of Geometrical Parameters Influence on Phenomenon Evolution

2004 ◽  
Vol 10 (6) ◽  
pp. 433-442 ◽  
Author(s):  
Giovanni Ferrara ◽  
Lorenzo Ferrari ◽  
Leonardo Baldassarre
Keyword(s):  
Centrifugal Compressor ◽  
Dynamic Pressure ◽  
Pressure Sensors ◽  
Experimental Tests ◽  
Fast Response ◽  
Rotating Stall ◽  
Geometrical Parameters ◽  
Vaneless Diffuser ◽  
Response Dynamic ◽  
Frequency Domains

The rotating stall is a key problem for achieving a good working range of a centrifugal compressor and a detailed understanding of the phenomenon is very important to anticipate and avoid it. Many experimental tests have been planned by the authors to investigate the influence on stall behavior of different geometrical configurations. A stage with a backward channel upstream, a 2-D impeller with a vaneless diffuser and a constant cross-section volute downstream, constitute the basic configuration. Several diffuser types with different widths, pinch shapes, and diffusion ratios were tested. The stage was instrumented with many fast response dynamic pressure sensors so as to characterize inception and evolution of the rotating stall. This kind of analysis was carried out both in time and in frequency domains. The methodology used and the results on phenomenon evolution will be presented and discussed in this article.

Sign in / Sign up

Export Citation Format

Share Document