scholarly journals The Effects of Diffuser Geometry on Rotating Stall Behavior

1988 ◽  
Author(s):  
M. V. Otugen ◽  
R. M. C. So ◽  
B. C. Hwang
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Critical Mass ◽  
Rotating Stall ◽  
Radius Ratio ◽  
Impeller Speed ◽  
Vaneless Diffuser ◽  
Room Condition ◽  
Inlet Opening

Experiments were carried out in a model vaneless diffuser rig to investigate the rotating stall phenomenon and its relation to diffuser geometry. The experimental rig consisted of an actual impeller which was used to deliver the flow to the vaneless diffuser. Mass flow rate through the system could be adjusted by varying the rotational speed of the impeller at a fixed inlet opening or by changing the inlet opening at a fixed impeller speed. The flow exited to room condition. As such, the rig was designed to investigate the fluid mechanics of vaneless diffuser rotating stall only. Attention was focused on the effects of diffuser width and radius on rotating stall. Three diffuser widths and three outlet radii were examined. The width-to-inlet radius ratio varied between 0.09 and 0.142 while the outlet-to-inlet radius ratio varied between 1.5 and 2. Results showed that the critical mass flow rate for the onset of rotating stall decreases with decreasing diffuser width. The critical mass flow rate is affected also by the diffuser radius ratio; larger radius ratios resulted in smaller critical mass flow rates. The ratio of the speed of rotation of the stall cell to impeller speed is found to decrease with increasing number of stall cells. This relative speed also decreases with increasing diffuser radius ratio, but it is largely independent of the diffuser width.

Control of Self-Excited Oscillations in Centrifugal Blowers

2007 ◽  
Author(s):  
Saad A. Ahmed
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Critical Mass ◽  
Industrial Applications ◽  
Rotating Stall ◽  
Operating Conditions ◽  
Flow Coefficient ◽  
Flow Area ◽  
The Stability

Centrifugal compressors or blowers are widely used in many industrial applications. However, the operation of such systems is limited at low-mass flow rates by self-excited flow instabilities which could result in rotating stall or surge of the compressor. These instabilities will limit the flow range in which the compressor or the blower can operate, and will also lower their performance and efficiency. Experimental techniques were used to investigate a model of radial vaneless diffuser at stall and stall-free operating conditions. The speed of the impeller was kept constant, while the mass flow rate was reduced gradually to study the steady and unsteady operating conditions of the compressor. Additional experiments were made to investigate the effects of reducing the exit flow area on the inception of stall. The results indicate that the instability in the diffuser was successfully delayed to a lower flow coefficient when throttle rings were attached to either one or both of the diffuser walls (i.e., to reduce the diffuser exit flow area). The results also showed that an increase of the blockage ratio improves the stability of the system (i.e., the critical mass flow rate could be reduced to 50% of its value without blockage). The results indicate that the throttle rings could be an effective method to control stall in radial diffusers.

An Experimental Investigation of the Effects of Vaneless Diffuser Geometry on the Stall Characteristics

2009 ◽  
Author(s):  
Saad A. Ahmed ◽  
Mohamed Gadalla
Keyword(s):  
Experimental Investigation ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Flow Instability ◽  
Rotating Stall ◽  
Width Ratio ◽  
Vaneless Diffuser ◽  
Pressure Pattern ◽  
Stall Cells

An experimental investigation of the flow instability characteristics in a radial vaneless diffuser of a centrifugal blower was carried out. The mass flow rate of air through the diffuser could be gradually reduced to zero value. The flowfield in the diffuser was measured using dynamic and static pressure transducers and the results are reported for steady and stall conditions. The objectives of this experimental investigation are to investigate, understand, and document the effects of diffuser geometry on the inception and fundamental characteristics of rotating stall, and also to provide a benchmark set of experimental data to aid stall model development. The results of this investigation showed that the maximum number of stall cells was two. The rotating pressure pattern with one stall cell was dominant; especially, if the mass flow rate is lower than the critical value for stall inception. The speeds of stall cells increase linearly with the impeller speed and they decrease with the increase of the diameter ratio. On the other hand, the effect of diffuser width ratio on the pressure pattern frequency is insignificant; therefore, it is not presented.

Stall Warning Using the Rotor Tip Pressure in a Transonic Axial Compressor With Circumferential Grooves

2018 ◽  
Author(s):  
Byeung Jun Lim ◽  
Tae Choon Park ◽  
Young Seok Kang
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Axial Compressor ◽  
Rotating Stall ◽  
Single Stage ◽  
Stall Inception ◽  
Casing Treatment ◽  
Stall Warning ◽  
Transonic Axial Compressor

In this study, characteristics of stall inception in a single-stage transonic axial compressor with circumferential grooves casing treatment were investigated experimentally. Additionally, the characteristic of increasing irregularity in the pressure inside circumferential grooves as the compressor approaches the stall limit was applied to the stall warning method. Spike-type rotating stall was observed in the single-stage transonic axial compressor with smooth casing. When circumferential grooves were applied, the stall inception was suppressed and the operating point of the compressor moved to lower flow rate than the stall limit. A spike-like disturbance was developed into a rotating stall cell and then the Helmholtz perturbation was overlapped on it at N = 80%. At N = 70 %, the Helmholtz perturbation was observed first and the amplitude of the wave gradually increased as mass flow rate decreased. At N = 60%, spike type stall inceptions were observed intermittently and then developed into continuous rotating stall at lower mass flow rate. Pressure measured at the bottom of circumferential grooves showed that the level of irregularity of pressure increased as flow rate decreased. Based on the characteristic of increasing irregularity of the pressure signals inside the circumferential grooves as stall approaches, an autocorrelation technique was applied to the stall warning. This technique could be used to provide warning against stall and estimate real-time stall margins in compressors with casing treatments.

Reduced-Order Modelling of Rotating Stall

2020 ◽  
Author(s):  
Dominik Schlüter ◽  
Robert P. Grewe ◽  
Fabian Wartzek ◽  
Alexander Liefke ◽  
Jan Werner ◽  
...  
Keyword(s):  
Single Cell ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Rotational Speed ◽  
Stability Limit ◽  
Rotating Stall ◽  
Operating Conditions ◽  
Transonic Compressor ◽  
Experimental Findings

Abstract Rotating stall is a non-axisymmetric disturbance in axial compressors arising at operating conditions beyond the stability limit of a stage. Although well-known, its driving mechanisms determining the number of stall cells and their rotational speed are still marginally understood. Numerical studies applying full-wheel 3D unsteady RANS calculations require weeks per operating point. This paper quantifies the capability of a more feasible quasi-2D approach to reproduce 3D rotating stall and related sensitivities. The first part of the paper deals with the validation of a numerical baseline the simplified model is compared to in detail. Therefore, 3D computations of a state-of-the-art transonic compressor are conducted. At steady conditions the single-passage RANS CFD matches the experimental results within an error of 1% in total pressure ratio and mass flow rate. At stalled conditions, the full-wheel URANS computation shows the same spiketype disturbance as the experiment. However, the CFD underpredicts the stalling point by approximately 7% in mass flow rate. In deep stall, the computational model correctly forecasts a single-cell rotating stall. The stall cell differs by approximately 21% in rotational speed and 18% in circumferential size from the experimental findings. As the 3D model reflects the compressor behaviour sufficiently accurate, it is considered valid for physical investigations. In the second part of the paper, the validated baseline is reduced in radial direction to a quasi-2D domain only resembling the compressor tip area. Four model variations regarding span-wise location and extent are numerically investigated. As the most promising model matches the 3D flow conditions in the rotor tip region, it correctly yields a single-cell rotating stall. The cell differs by only 7% in circumferential size from the 3D results. Due to the impeded radial migration in the quasi-2D slice, however, the cell exhibits an increased axial extent. It is assumed, that the axial expansion into the adjacent rows causes the difference in cell speed by approximately 24%. Further validation of the reduced model against experimental findings reveals, that it correctly reflects the sensitivity of circumferential cell size to flow coefficient and individual cell speed to compressor shaft speed. As the approach reduced the wall clock time by 92%, it can be used to increase the physical understanding of rotating stall at much lower costs.

Effects of Burner Diameter and Fuel Type on Smoke Point and Radiation Characteristics of Diffusion Flames

2002 ◽  
Author(s):  
S. F. Goh ◽  
S. Kusadomi ◽  
S. R. Gollahalli
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Critical Mass ◽  
Smoke Point ◽  
Fuel Type ◽  
Fuel Flow Rate ◽  
Flame Radiation ◽  
Fuel Mass ◽  
Fuel Flow

The main purpose of this study was to comprehend the effects of burner diameter and fuel type on smoke point characteristics of a hydrocarbon diffusion flame and its radiation emission. The critical mass flow rate of pure fuel at this smoke point was measured. At nine different fractions of the critical mass flow rate, nitrogen gas was supplied along with the fuel to achieve smoke point. At each condition, flame radiation and flame height were measured. The axial radiation profile at the critical fuel mass flow rate for one burner was also measured. Three fuels of differing sooting propensities were used: ethylene (C2H4), propylene (C3H6), and propane (C3H8). Three different burners with inner diameters of 1.2 mm, 3.2 mm and 6.4 mm were used. Results showed that propylene had the highest critical fuel flow rate and the highest nitrogen dilution required to suppress smoking and total flame radiation, followed by ethylene and propane. For all fuels, the curves of nitrogen flow rate required for smoke suppression versus fuel flow rate exhibited a skewed bell shape. The variation of Reynolds number at the critical fuel mass flow rate with the burner diameter showed a linear relation. On the other hand, the variation of total flame radiation with burner diameter was nonlinear.

A Theoretical Assessment of Napier’s Law

1987 ◽  
Vol 109 (4) ◽  
pp. 460-463
Author(s):  
Y. Candau
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Theoretical Approach ◽  
Critical Mass ◽  
Thermodynamic Calculations ◽  
Numerical Computations ◽  
Water Steam ◽  
Theoretical Assessment

Napier’s Law is advantageous for calculating critical mass flow rate of water-steam mixture. On the basis of numerical computations, it has been recently extended to a number of fluids. A theoretical approach using simple thermodynamic calculations can account for the existence of such a law when a few basic conditions are fulfilled.

scholarly journals Temperature Rise in the Multistage Axial Flow Compressor During Rotating Stall and Surge

1988 ◽  
Author(s):  
Katerina Nácovská
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Axial Flow ◽  
Rotating Stall ◽  
Rotor Speed ◽  
Absolute Level ◽  
Axial Flow Compressor ◽  
Temperature Levels ◽  
Flow Compressor

An experimental investigation of rotating stall and surge was carried out on a four stage axial flow compressor. Results of flow and blade temperature measurements in the compressor are presented. Internal temperature levels during rotating stall and surge are considerably higher than those obtained during unstalled compressor operation. In the pure rotating stall regime, the temperature is almost identical in all compressor stages and depends only on rotor speed and mass flow rate. During surge, the highest temperature is found at the tip diameter prior to the first stage rotor. The absolute level depends on rotor speed, mass flow rate (i.e. throttle position) and on the number of compressor stages. A model of the temperature changes in the multistage compressor during the surge cycle has been derived from the experiments.

Sign in / Sign up

Export Citation Format

Share Document