Allowable Ranges of Conventional Forging Parameters Determination for TA15 Ti-Alloy to Obtain Tri-modal Microstructure Under Given Subsequent Heat Treatment

JOM ◽  
2019 ◽  
Vol 71 (12) ◽  
pp. 4746-4757
Author(s):  
Zhichao Sun ◽  
Zhikun Yin ◽  
Jing Cao ◽  
Long Huang
Keyword(s):  
Heat Treatment ◽  
Subsequent Heat Treatment ◽  
Ti Alloy

scholarly journals Evaluation of Subsequent Heat Treatment Routes for Near-β Forged TA15 Ti-Alloy

Materials ◽  
2016 ◽  
Vol 9 (11) ◽  
pp. 872 ◽  
Author(s):  
Zhichao Sun ◽  
Huili Wu ◽  
He Yang
Keyword(s):  
Heat Treatment ◽  
Subsequent Heat Treatment ◽  
Ti Alloy

Effects of extrusion ratio and subsequent heat treatment on the tension-compression yield asymmetry of Mg-4.58Zn-2.6Gd-0.18Zr alloys

2021 ◽  
Vol 810 ◽  
pp. 141021
Author(s):  
Lei Xiao ◽  
Guangyu Yang ◽  
Risheng Pei ◽  
Zhili Zhen ◽  
Wanqi Jie
Keyword(s):  
Heat Treatment ◽  
Extrusion Ratio ◽  
Subsequent Heat Treatment

Combination of hot isostatic pressing and subsequent heat treatment for additively manufactured Zr-1Mo components

2021 ◽  
Vol 285 ◽  
pp. 129123
Author(s):  
Xiaohao Sun ◽  
Debao Liu ◽  
Minfang Chen ◽  
Weiwei Zhou ◽  
Naoyuki Nomura ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Hot Isostatic Pressing ◽  
Subsequent Heat Treatment ◽  
Isostatic Pressing

Engineering mechanical properties by controlling the microstructure of an Fe–Ni–Mn martensitic steel through pre-cold rolling and subsequent heat treatment

2021 ◽  
Vol 804 ◽  
pp. 140760
Author(s):  
Hamidreza Koohdar ◽  
Pouya Hakimipour ◽  
Hamid Reza Jafarian ◽  
Terence G. Langdon ◽  
Mahmoud Nili-Ahmadabadi
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Cold Rolling ◽  
Martensitic Steel ◽  
Subsequent Heat Treatment

Preparation of Hydroxyapatite/Chitosan Biological Coatings on Carbon/Carbon Composites

2010 ◽  
Vol 434-435 ◽  
pp. 502-505
Author(s):  
Ying Hua Li ◽  
Li Yun Cao ◽  
Jian Feng Huang ◽  
Xie Rong Zeng
Keyword(s):  
Heat Treatment ◽  
Electrophoretic Deposition ◽  
Isopropyl Alcohol ◽  
Raw Materials ◽  
Composite Coatings ◽  
Thermal Conditions ◽  
Hydrothermal Condition ◽  
Subsequent Heat Treatment ◽  
Carbon Composites ◽  
Deposition Voltage

Hydroxyapatite/Chitosan (HAp/CS) bio-coatings were prepared on the surface of carbon/ carbon (C/C) composites by hydrothermal electrophoretic deposition, using sonochemical process resulted HAp nanoparticles, isopropyl alcohol and chitosan as raw materials. The influences of hydro- thermal conditions and deposition voltage on the microstructures and morphologies of the as-prepared coatings were investigated. It was shown that homogenous and dense HAp/CS coatings on C/C composites are obtained by hydrothermal electrophoretic deposition. With the increase of deposition voltage, density and homogeneity of the as-prepared HAp/CS composite coatings are well improved. Due to the growth of HAp nanoparticles in the hydrothermal condition, the subsequent heat treatment of the HAp/CS coatings is not needed.

Growth of polycrystalline hydroxyapatite thin films by pulsed laser deposition and subsequent heat treatment in air

1998 ◽  
Author(s):  
V. D. Nelea ◽  
Cornel Ghica ◽  
C. Martin ◽  
Alexandru Hening ◽  
Ion N. Mihailescu ◽  
...  
Keyword(s):  
Thin Films ◽  
Heat Treatment ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Subsequent Heat Treatment ◽  
Laser Deposition
Sign in / Sign up

Export Citation Format

Share Document