Engineering mechanical properties by controlling the microstructure of an Fe–Ni–Mn martensitic steel through pre-cold rolling and subsequent heat treatment

2021 ◽  
Vol 804 ◽  
pp. 140760
Author(s):  
Hamidreza Koohdar ◽  
Pouya Hakimipour ◽  
Hamid Reza Jafarian ◽  
Terence G. Langdon ◽  
Mahmoud Nili-Ahmadabadi
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Cold Rolling ◽  
Martensitic Steel ◽  
Subsequent Heat Treatment

scholarly journals The Effect of Quenching and Partitioning (Q&P) Heat Treatment on the Microstructure and Mechanical Properties of High Boron Steel

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1556
Author(s):  
Zhao Li ◽  
Run Wu ◽  
Mingwei Li ◽  
Song-Sheng Zeng ◽  
Yu Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Volume Fraction ◽  
Martensitic Steel ◽  
Boron Steel ◽  
Quenching And Partitioning ◽  
Effect Mechanism ◽  
Microstructure And Mechanical Properties ◽  
High Boron ◽  
Cast Condition

High boron steel is prone to brittle failure due to the boride distributed in it with net-like or fishbone morphology, which limit its applications. The Quenching and Partitioning (Q&P) heat treatment is a promising process to produce martensitic steel with excellent mechanical properties, especially high toughness by increasing the volume fraction of retained austensite (RA) in the martensitic matrix. In this work, the Q&P heat treatment is used to improve the inherent defect of insufficient toughness of high boron steel, and the effect mechanism of this process on microstructure transformation and the change of mechanical properties of the steel has also been investigated. The high boron steel as-casted is composed of martensite, retained austensite (RA) and eutectic borides. A proper quenching and partitioning heat treatment leads to a significant change of the microstructure and mechanical properties of the steel. The net-like and fishbone-like boride is partially broken and spheroidized. The volume fraction of RA increases from 10% in the as-cast condition to 19%, and its morphology also changes from blocky to film-like. Although the macro-hardness has slightly reduced, the toughness is significantly increased up to 7.5 J·cm−2, and the wear resistance is also improved.

scholarly journals Effect of Cold Rolling and Heat Treatment on the Mechanical Properties of GH4169 Alloy Sheet at Room Temperature

Metals ◽  
2015 ◽  
Vol 6 (1) ◽  
pp. 1 ◽  
Author(s):  
Shi-Hong Zhang ◽  
Neng-Yong Ye ◽  
Ming Cheng ◽  
Hong-Wu Song ◽  
Hong-Wei Zhou ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Cold Rolling ◽  
Room Temperature ◽  
Alloy Sheet ◽  
Gh4169 Alloy

Influence of Heat-Treatment on Properties, Microstructure and Corrosion Resistant of Zirconium Sheet

2014 ◽  
Vol 936 ◽  
pp. 1796-1800
Author(s):  
Peng Dang ◽  
Xiao Wei Zhang ◽  
Yun Wang ◽  
Qing Zhang ◽  
Chang Liang Li
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Yield Strength ◽  
Cold Rolling ◽  
Annealing Temperature ◽  
Experimental Results ◽  
Corrosion Resistant ◽  
Mechanical Properties And Corrosion

The influence of annealing temperature on the microstructure, mechanical properties and corrosion resistant of cold rolling zirconium sheet were studied in the manuscript. The experimental results shown that the tensile strength and yield strength of zirconium sheet were decreased and the elongationwas raised with the raising of annealing temperature from 500 °C to 580 °C. The recrystallization are not happened in zirconium sheet at the annealing temperature of 500 °C. Zirconium sheet complete recrystallized and the strength and elongation get a well match at the annealing temperature of 540°C. Zirconium sheet also complete recrystallized at the annealing temperature of 580°C but the crystalline grain has the tendency of growing. The annealing temperature has no effect on the corrosion resistant of zirconium sheet.

scholarly journals Effect of Microstructures and Mechanical Properties of Large Deformation High Entropy Alloy CoCrCuFeNi in Semi-solid Isothermal Heat Treatment

2020 ◽  
Vol 1 (2) ◽  
Author(s):  
Lajie WANG ◽  
Jiao XIONG ◽  
Jun LIU ◽  
X J YANG
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Cold Rolling ◽  
Liquid Fraction ◽  
Grain Morphology ◽  
High Entropy Alloy ◽  
Isothermal Heat Treatment ◽  
Scanning Calorimetry ◽  
High Entropy ◽  
Semi Solid

The semi-solid slurries of the CoCrCuFeNi high entropy alloy (HEA) were fabricated through the recrystallization and partial melting (RAP) process by cold-rolling and partial remelting. The temperature range of the semi-solid region and the relationship between the liquid fraction and the temperature were determined by the differential scanning calorimetry (DSC) curve. The effect of isothermal temperature and holding time on the evolution of the microstructure and mechanical properties of the rolled samples was analyzed. The results show that the microstructure was significantly deformed, and the tensile strength has been increased by 107% after 63% rolling deformation of the CoCrCuFeNi high entropy alloy (HEA). The high-entropy alloy after cold rolling was maintained at 1150 and 1300 ° C for 20, 30, 60, and 120 minutes respectively, the plasticity has been improved compared with the rolled high entropy alloy. The optimal plasticity was reached 13.7% and 7.9% at 1150 ℃ and 1300℃ for 30 minutes, respectively. After semi-solid isothermal heat treatment, the grain morphology changed from dendritic of as-cast or rolled to spherulite and the grain size increased significantly with time and the holding temperature increased.

Sign in / Sign up

Export Citation Format

Share Document