Volume Compatibility of Interlayer Treatment Materials with Roller-Compacted Concrete

2021 ◽  
Author(s):  
Xiaoliang Zhu ◽  
Yuxin Gao ◽  
Wenjing Song ◽  
Jingjing Xu ◽  
Chengyang Li ◽  
...  
Keyword(s):  
Roller Compacted Concrete

scholarly journals Roller Compacted Concrete with Recycled Concrete Aggregate for Paving Bases

2020 ◽  
Vol 12 (8) ◽  
pp. 3154 ◽  
Author(s):  
Hedelvan Emerson Fardin ◽  
Adriana Goulart dos Santos
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Modulus Of Elasticity ◽  
Splitting Tensile Strength ◽  
Recycled Concrete ◽  
Concrete Aggregate ◽  
Recycled Concrete Aggregate ◽  
Roller Compacted Concrete ◽  
Flexural Tensile Strength ◽  
Mechanical And Physical Properties

This research aimed to investigate the mechanical and physical properties of Roller Compacted Concrete (RCC) used with Recycled Concrete Aggregate (RCA) as a replacement for natural coarse aggregate. The maximum dry density method was adopted to prepare RCC mixtures with 200 kg/m³ of cement content and coarse natural aggregates in the concrete mixture. Four RCC mixtures were produced from different RCA incorporation ratios (0%, 5%, 15%, and 30%). The compaction test, compressive strength, splitting tensile strength, flexural tensile strength, and modulus of elasticity, porosity, density, and water absorption tests were performed to analyze the mechanical and physical properties of the mixtures. One-way Analysis of Variance (ANOVA) was used to identify the influences of RCA on RCC’s mechanical properties. As RCA increased in mixtures, some mechanical properties were observed to decrease, such as modulus of elasticity, but the same was not observed in the splitting tensile strength. All RCCs displayed compressive strength greater than 15.0 MPa at 28 days, splitting tensile strength above 1.9 MPa, flexural tensile strength above 2.9 MPa, and modulus of elasticity above 19.0 GPa. According to Brazilian standards, the RCA added to RCC could be used for base layers.

Long-term thermal two- and three-dimensional analysis of roller compacted concrete dams supported by monitoring verification

2010 ◽  
Vol 37 (4) ◽  
pp. 600-610 ◽  
Author(s):  
Vladan Kuzmanovic ◽  
Ljubodrag Savic ◽  
John Stefanakos
Keyword(s):  
Thermal Analysis ◽  
Boundary Conditions ◽  
Thermal Field ◽  
Numerical Models ◽  
Three Dimensional ◽  
Roller Compacted Concrete ◽  
Rcc Dam ◽  
Field Investigations ◽  
Good Agreement

This paper presents two-dimensional (2D) and three-dimensional (3D) numerical models for unsteady phased thermal analysis of RCC dams. The time evolution of a thermal field has been modeled using the actual dam shape, RCC technology and the adequate description of material properties. Model calibration and verification has been done based on the field investigations of the Platanovryssi dam, the highest RCC dam in Europe. The results of a long-term thermal analysis, with actual initial and boundary conditions, have shown a good agreement with the observed temperatures. The influence of relevant parameters on the thermal field of RCC dams has been analyzed. It is concluded that the 2D model is appropriate for the thermal phased analysis, and that the boundary conditions and the mixture properties are the most influential on the RCC dam thermal behavior.

The Feasibility of Using Micro Silica Sand Powder as Partial Replacement of Cement in Production of Roller Compacted Concrete

2021 ◽  
Vol 1021 ◽  
pp. 21-34
Author(s):  
Zahraa Alaa M.A. Ali Khan ◽  
Zena K. Abbas
Keyword(s):  
Portland Cement ◽  
Minimum Cost ◽  
The Other ◽  
Silica Sand ◽  
Engineering Properties ◽  
Crushed Stone ◽  
Partial Replacement ◽  
Roller Compacted Concrete ◽  
Water Curing ◽  
Micro Silica

Roller compacted concrete (RCC) is a special type of concrete with zero or even negative slump consistency. In this work, it had aimed to produce an RCC mix suitable for roads paving with minimum cost and better engineering properties so, different RCC mixes had prepared i.e. (M1, M2, M3, and M4) using specified percentages of micro natural silica sand powder (SSP) as partial replacement of (0%, 5%, 10%, and 20%) by weight of sulfate resistant Portland cement. Additionally, M-sand, crushed stone, filler, and water had been used. The results had obtained after 28 days of water curing. The control mix (M1) had satisfied the required f ‘c with accepted results for the other tests. M2 mix with SSP of 5% had achieved the highest results. The f ’c for sawed cubes of (10*10*10) cm had increased by 2.26% and 3.16% when tested in directions (ꓕ and //) to the direction of loading respectively. R results for sawed prisms of (38*10*10) cm had increased by 8.78% and 8.43% when tested on top and bottom faces respectively. The density had increased by 1.04% while the absorption and volume of permeable voids had decreased by 8.11% and 7.83% respectively. The UPV results had also increased by 2.44% and 0.81% for cubes and prisms respectively when compared to the control mix. M3 mix with SSP of 10% had also achieved satisfactory results when compared to the control mix.

Sign in / Sign up

Export Citation Format

Share Document