A study on the failure mechanism and wear loss of impregnated diamond bits during machining process of armor ceramics

2018 ◽  
Vol 32 (1) ◽  
pp. 261-268 ◽  
Author(s):  
Lei Zheng ◽  
Haixiang Huan ◽  
Yong Zeng ◽  
Shuquan Song ◽  
Shili Cheng ◽  
...  
Keyword(s):  
Failure Mechanism ◽  
Machining Process ◽  
Wear Loss ◽  
Armor Ceramics ◽  
Impregnated Diamond Bits

Deformation Replication

1970 ◽  
Vol 28 ◽  
pp. 280-281
Author(s):  
J. Temple Black
Keyword(s):  
Cutting Speed ◽  
Machining Process ◽  
Depth Of Cut ◽  
Rake Face ◽  
Orthogonal Machining ◽  
Aluminum Chips ◽  
Before And After ◽  
Materials Used ◽  
Glass Knife ◽  
Very High

Tool materials used in ultramicrotomy are glass, developed by Latta and Hartmann (1) and diamond, introduced by Fernandez-Moran (2). While diamonds produce more good sections per knife edge than glass, they are expensive; require careful mounting and handling; and are time consuming to clean before and after usage, purchase from vendors (3-6 months waiting time), and regrind. Glass offers an easily accessible, inexpensive material ($0.04 per knife) with very high compressive strength (3) that can be employed in microtomy of metals (4) as well as biological materials. When the orthogonal machining process is being studied, glass offers additional advantages. Sections of metal or plastic can be dried down on the rake face, coated with Au-Pd, and examined directly in the SEM with no additional handling (5). Figure 1 shows aluminum chips microtomed with a 75° glass knife at a cutting speed of 1 mm/sec with a depth of cut of 1000 Å lying on the rake face of the knife.

On the role of tin underlays for the prevention of thermal grooving in thin gold films

1986 ◽  
Vol 44 ◽  
pp. 732-733
Author(s):  
Jin Young Kim ◽  
R. E. Hummel ◽  
R. T. DeHoff
Keyword(s):  
Thin Film ◽  
Free Surface ◽  
Grain Boundary ◽  
Beneficial Effect ◽  
Failure Mechanism ◽  
Failure Mechanisms ◽  
Distinct Advantage ◽  
Gold Films ◽  
Gold Thin Film

Gold thin film metallizations in microelectronic circuits have a distinct advantage over those consisting of aluminum because they are less susceptible to electromigration. When electromigration is no longer the principal failure mechanism, other failure mechanisms caused by d.c. stressing might become important. In gold thin-film metallizations, grain boundary grooving is the principal failure mechanism.Previous studies have shown that grain boundary grooving in gold films can be prevented by an indium underlay between the substrate and gold. The beneficial effect of the In/Au composite film is mainly due to roughening of the surface of the gold films, redistribution of indium on the gold films and formation of In2O3 on the free surface and along the grain boundaries of the gold films during air annealing.

Performance Analysis on Eco-friendly Machining of Ti6Al4V using Powder Mixed with Different Dielectrics in WEDM

2020 ◽  
Vol 17 (3) ◽  
pp. 8128-8139
Author(s):  
S. Chakraborty ◽  
S. Mitra ◽  
D. Bose
Keyword(s):  
Metal Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Process Efficiency ◽  
Machining Parameters ◽  
Dielectric Fluids ◽  
High Emission ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Wedm Process

The recent scenario of modern manufacturing is tremendously improved in the sense of precision machining and abstaining from environmental pollution and hazard issues. In the present work, Ti6Al4V is machined through wire EDM (WEDM) process with powder mixed dielectric and analyzed the influence of input parameters and inherent hazard issues. WEDM has different parameters such as peak current, pulse on time, pulse off time, gap voltage, wire speed, wire tension and so on, as well as dielectrics with powder mixed. These are playing an essential role in WEDM performances to improve the process efficiency by developing the surface texture, microhardness, and metal removal rate. Even though the parameter’s influencing, the study of environmental effect in the WEDM process is very essential during the machining process due to the high emission of toxic vapour by the high discharge energy. In the present study, three different dielectric fluids were used, including deionised water, kerosene, and surfactant added deionised water and analysed the data by taking one factor at a time (OFAT) approach. From this study, it is established that dielectric types and powder significantly improve performances with proper set of machining parameters and find out the risk factor associated with the PMWEDM process.

Commercial Trailer Tires: Tire Inflation and Its Effect on Rolling Resistance, Fuel Economy, and Tire Footprint

2015 ◽  
Vol 43 (2) ◽  
pp. 144-162
Author(s):  
Al Cohn
Keyword(s):  
Fuel Economy ◽  
Rolling Resistance ◽  
Maintenance Cost ◽  
Wear Loss ◽  
Truck Tires ◽  
Footprint Analysis ◽  
Subsequent Loss ◽  
Resistance Data

ABSTRACT Maintaining proper tire inflation is the number one issue facing commercial fleets today. Common, slow-leaking tread area punctures along with leaking valve stems and osmosis through the tire casing lead to tire underinflation with a subsequent loss in fuel economy, reduction in retreadability, tread wear loss, irregular wear, and increase in tire-related roadside service calls. Commercial truck tires are the highest maintenance cost for fleets second only to fuel. This article will examine tire footprint analysis, rolling resistance data, and the effect on vehicle fuel economy from tires run at a variety of underinflated, overinflated, and recommended tire pressures. This analysis will also include the tire footprint impact by running tires on both fully loaded and unloaded trailers. The footprint analysis addresses both standard dual tires (295/75R22.5) along with the newer increasingly popular wide-base tire size 445/50R22.5.

Modeling of Self-Induced Vibrations that Occur During the Machining Process of Casting Patterns with the Use of The Fuzzy-Neural Networks Method

2013 ◽  
Vol 58 (3) ◽  
pp. 871-875
Author(s):  
A. Herberg
Keyword(s):  
Neural Networks ◽  
Control System ◽  
Network Structure ◽  
Fuzzy Systems ◽  
Fuzzy Neural Networks ◽  
Cnc Machining ◽  
Machining Process ◽  
Modeling Process ◽  
Fuzzy Neural ◽  
Takagi Sugeno

Abstract This article outlines a methodology of modeling self-induced vibrations that occur in the course of machining of metal objects, i.e. when shaping casting patterns on CNC machining centers. The modeling process presented here is based on an algorithm that makes use of local model fuzzy-neural networks. The algorithm falls back on the advantages of fuzzy systems with Takagi-Sugeno-Kanga (TSK) consequences and neural networks with auxiliary modules that help optimize and shorten the time needed to identify the best possible network structure. The modeling of self-induced vibrations allows analyzing how the vibrations come into being. This in turn makes it possible to develop effective ways of eliminating these vibrations and, ultimately, designing a practical control system that would dispose of the vibrations altogether.

SURFACE IRREGULARITIES AS A COMPLEX SIGNAL OF TOOL REPRESENTATION TOGETHER WITH UNEVEN DISPLACEMENT IN RESPECT TO THE WORKPIECE

2014 ◽  
Vol 21 (1) ◽  
pp. 133-144 ◽  
Author(s):  
Adam Boryczko ◽  
Wojciech Rytlewski
Keyword(s):  
Machining Process ◽  
Surface Irregularity ◽  
Complex Signal ◽  
Complex Phenomenon ◽  
Tool Profile ◽  
Surface Irregularities ◽  
The Individual ◽  
Frequency Functions

Abstract In a dynamic machining process, distortion in surface irregularity is a very complex phenomenon. Surface irregularities form a periodic representation of the tool profile with various kinds of disturbance in a broad range of changes in the height and length of the profile. To discern these irregularity disturbances, interactions of the tool in the form of changes perpendicular and parallel relative to the workpiece were analyzed and simulated. The individual kinds of displacement of the tool relative to the workpiece introduce distortions in the changes of height and length. These changes are weakly represented in standard height and length irregularity parameters and their discernment has been found through amplitude-frequency functions.

Influence of Air Entrappment on Flood Embankment Failure Mechanism - Model Tests

2008 ◽  
Vol 11 (-1) ◽  
pp. 188-201 ◽  
Author(s):  
Piotr Bogacz ◽  
Jarosława Kaczmarek ◽  
Danuta Leśniewska
Keyword(s):  
Failure Mechanism ◽  
Model Tests ◽  
Mechanism Model

Studying The Effect of a New Mixed Cutting Fluid on Surface Roughness

2020 ◽  
Vol 38 (11A) ◽  
pp. 1593-1601
Author(s):  
Mohammed H. Shaker ◽  
Salah K. Jawad ◽  
Maan A. Tawfiq
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Cutting Parameters ◽  
Machining Process ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Cutting Fluids ◽  
Machining Processes ◽  
Dry Cutting ◽  
Cutting Speeds

This research studied the influence of cutting fluids and cutting parameters on the surface roughness for stainless steel worked by turning machine in dry and wet cutting cases. The work was done with different cutting speeds, and feed rates with a fixed depth of cutting. During the machining process, heat was generated and effects of higher surface roughness of work material. In this study, the effects of some cutting fluids, and dry cutting on surface roughness have been examined in turning of AISI316 stainless steel material. Sodium Lauryl Ether Sulfate (SLES) instead of other soluble oils has been used and compared to dry machining processes. Experiments have been performed at four cutting speeds (60, 95, 155, 240) m/min, feed rates (0.065, 0.08, 0.096, 0.114) mm/rev. and constant depth of cut (0.5) mm. The amount of decrease in Ra after the used suggested mixture arrived at (0.21µm), while Ra exceeded (1µm) in case of soluble oils This means the suggested mixture gave the best results of lubricating properties than other cases.

Sign in / Sign up

Export Citation Format

Share Document