Effects of relative tool sharpness on surface generation mechanism of precision turning of electroless nickel-phosphorus coating

2021 ◽  
Author(s):  
Qian Yu ◽  
Tianfeng Zhou ◽  
Yupeng He ◽  
Peng Liu ◽  
Xibin Wang ◽  
...  
Keyword(s):  
Electroless Nickel ◽  
Generation Mechanism ◽  
Surface Generation ◽  
Precision Turning

Generation mechanism modeling of surface topography in tangential ultrasonic vibration-assisted grinding with green silicon carbide abrasive wheel

2021 ◽  
pp. 095440542110406
Author(s):  
Yutong Qiu ◽  
Jingfei Yin ◽  
Yang Cao ◽  
Wenfeng Ding
Keyword(s):  
Surface Roughness ◽  
Surface Topography ◽  
Ultrasonic Vibration ◽  
Generation Mechanism ◽  
Surface Generation ◽  
Depth Of Cut ◽  
Abrasive Wheel ◽  
Grinding Parameters ◽  
Conventional Grinding ◽  
Ultrasonic Vibration Assisted Grinding

Tangential ultrasonic vibration-assisted grinding (TUAG) has a wide prospect in machining difficult-to-machine materials. However, the surface generation mechanism in TUAG is not fully recovered. This study proposes an analytical model of the surface topography produced by TUAG. Based on the model, the surface topography and roughness are predicted and experimentally verified. In addition, the influence of the grinding parameters on the surface topography is analyzed. The predicted surface topography well coincides with experimental measurements, and the prediction error in surface roughness Ra by the proposed model is less than 5%. Compared with conventional grinding, TUAG produces a surface with more uniform scratches and surface roughness Ra was reduced by up to 27% with the proper parameters. However, the improvement of surface roughness in TUAG is weakened when grinding speed or depth of cut increases. Moreover, the influence of the ultrasonic vibration amplitude on the surface roughness is not monotonous. With the grinding parameters selected in this study, TUAG with an ultrasonic amplitude of 7.5 μm produces the minimum surface roughness.

scholarly journals Simulation and Experimental Study on the Surface Generation Mechanism of Cu Alloys in Ultra-Precision Diamond Turning

Micromachines ◽  
2019 ◽  
Vol 10 (9) ◽  
pp. 573
Author(s):  
Zhang ◽  
Guo ◽  
Chen ◽  
Fu ◽  
Zhao
Keyword(s):  
Tool Wear ◽  
Diamond Tool ◽  
Surface Characteristics ◽  
Diamond Turning ◽  
Generation Mechanism ◽  
Surface Generation ◽  
Machining Parameters ◽  
Nose Radius ◽  
Cu Alloys ◽  
Ultra Precision

The surface generation mechanism of the Cu alloys in ultra-precision diamond turning is investigated by both simulation and experimental methods, where the effects of the cutting parameters on the surface characteristics are explored, including the workpiece spindle speed, the cutting depth, the feed rate and the nose radius of the diamond tool. To verify the built model, the cutting experiments are conducted at selected parameters, where the causes of the error between the simulation and the machining results are analyzed, including the effects of the materials microstructure and the diamond tool wear. In addition, the nanometric surface characteristics of the Cu alloys after the diamond turning are identified, including the finer scratching grooves caused by the tool wear, the formation of the surface burs and the adhesion of graphite. The results show that the built model can be basically used to predict the surface topography for the selection of the appropriate machining parameters in the ultra-precision diamond turning process.

Spherical surface generation mechanism in the grinding of balls for ultraprecision ball bearings

2000 ◽  
Vol 214 (4) ◽  
pp. 351-357 ◽  
Author(s):  
B Zhang ◽  
A Nakajima
Keyword(s):  
Kinematic Analysis ◽  
High Speed ◽  
Spherical Surface ◽  
Generation Mechanism ◽  
Surface Generation ◽  
Ball Bearings ◽  
Contact Points ◽  
Ball Surface ◽  
Precision Machines ◽  
Good Agreement

Ultraprecision ball bearings are necessary for high-precision machines and/or high-speed machines since the vibration caused by ball bearings determines the precision of machines as a whole and may make high-speed machines fail to work. To produce ultraprecision ball bearings, it is necessary to clarify spherical surface generation mechanism in the grinding of balls. This paper is the first attempt to investigate the contact trace distribution on the ball surface, which is crucial to spherical surface generation. The kinematic analysis of the contact trace shows that the contact trace is a fixed circle on the ball surface and the contact points are not uniformly distributed on the ball surface. Experimental observation of the contact trace was also carried out. The observation is in good agreement with the analysis. Suggestions on how to distribute the contact trace over the whole ball surface and therefore to improve the precision of balls are given.

scholarly journals Lapped Surface Generation Mechanism of Unidirectional Fiber Reinforced Composite Materials

2015 ◽  
Vol 81 (7) ◽  
pp. 668-672
Author(s):  
Mitsugu YAMAGUCHI ◽  
Satoshi SAKAMOTO ◽  
Yasuo KONDO ◽  
Kenji YAMAGUCHI ◽  
Keitoku HAYASHI
Keyword(s):  
Composite Materials ◽  
Generation Mechanism ◽  
Surface Generation ◽  
Fiber Reinforced ◽  
Fiber Reinforced Composite ◽  
Unidirectional Fiber ◽  
Reinforced Composite
Sign in / Sign up

Export Citation Format

Share Document