The Influence of Adopted Chemical Modification Route on the Thermal and Mechanical Properties of Alumina Nanoparticles-Impregnated Thermoplastic Natural Rubber Nanocomposite

2019 ◽  
Vol 45 (2) ◽  
pp. 1181-1190 ◽  
Author(s):  
Moayad Husein Flaifel ◽  
Muhammad Zaidi Zakaria ◽  
Sahrim Hj Ahmad
Keyword(s):  
Mechanical Properties ◽  
Chemical Modification ◽  
Natural Rubber ◽  
Alumina Nanoparticles ◽  
Thermal And Mechanical Properties ◽  
Thermoplastic Natural Rubber

scholarly journals Composites from Thermoplastic Natural Rubber Reinforced Rubberwood Sawdust: Effects of Sawdust Size and Content on Thermal, Physical, and Mechanical Properties

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Chatree Homkhiew ◽  
Surasit Rawangwong ◽  
Worapong Boonchouytan ◽  
Wiriya Thongruang ◽  
Thanate Ratanawilai
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
High Density Polyethylene ◽  
High Performance ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Shore Hardness ◽  
Thermoplastic Natural Rubber ◽  
Plastic Content

The aim of this work is to investigate the effects of rubberwood sawdust (RWS) size and content as well as the ratio of natural rubber (NR)/high-density polyethylene (HDPE) blend on properties of RWS reinforced thermoplastic natural rubber (TPNR) composites. The addition of RWS about 30–50 wt% improved the modulus of the rupture and tensile strength of TPNR composites blending with NR/HDPE ratios of 60/40 and 50/50. TPNR composites reinforced with RWS 80 mesh yielded better tensile strength and modulus of rupture than the composites with RWS 40 mesh. The TPNR/RWS composites with larger HDPE content gave higher tensile, flexural, and Shore hardness properties and thermal stability as well as lower water absorption. The TPNR/RWS composites with larger plastic content were therefore suggested for applications requiring high performance of thermal, physical, and mechanical properties.

Phase Morphology, Thermal and Mechanical Properties of Compatibilized Nylon12/Natural Rubber Blends Using PS/MNR

2013 ◽  
Vol 844 ◽  
pp. 53-56
Author(s):  
Saravalee Saengthaveep ◽  
Sadhan C. Jana ◽  
Rathanawan Magaraphan
Keyword(s):  
Mechanical Properties ◽  
Natural Rubber ◽  
Moisture Absorption ◽  
Rubber Particle ◽  
Impact Resistance ◽  
Phase Morphology ◽  
Thermal And Mechanical Properties ◽  
Binary Blend ◽  
Polyamide 12 ◽  
The Impact

To produce a tough material for application demanding high impact resistance and low moisture absorption, melt blending of Nylon12 (Polyamide 12, PA12) and natural rubber (NR) was carried out in a brabender plasticorder at 210 °C with rotor speed of 70 rpm in the presence of polystyrene/maleated natural rubber (PS/MNR) blend as a compatibilizer. The effect of compatibilizer content (1, 3, 5, 7 and 10 phr) on phase morphology, thermal, and mechanical properties of [Nylon12/NR]/[PS/MNR] blends was investigated by using SEM, DSC, and Izod impact tester, respectively. The result revealed that PS/MNR blend improved the compatibility of Nylon12/NR blends efficiently due to the presence of amide linkage at the interfaces from the reaction between the reactive groups of MNR and the NH2 end groups of Nylon12 during mixing. A fine phase morphology (good dispersion and small dispersed phase size of NR domains in Nylon12 matrix) of [Nylon12/NR]/[PS/MNR] blends was observed at the optimum compatibilizer content of 7 phr, relating to the improvement of mechanical property. The impact energy of [Nylon12/NR]/[PS/MNR] blends was 503 J/m higher than that of neat Nylon12 (115 J/m) and Nylon12/NR binary blend (241 J/m) due to the toughening effect of rubber and proper morphology. The melting temperature of all blends did not change obviously from thermal analysis. However, the presence of rubber particle obstructed the crystallization of Nylon12 phase, leading to the decreasing of %crystallinity from 93% to around 70%.

Morphology and Mechanical Properties of NiZn Ferrite/Thermoplastic Natural Rubber Composite

2014 ◽  
Vol 925 ◽  
pp. 308-312 ◽  
Author(s):  
Mou'ad A. Tarawneh ◽  
Sahrim Haji Ahmad ◽  
Yu Li Jiun ◽  
Radwan Dweiri ◽  
Ibrahim N. Hassan
Keyword(s):  
Mechanical Properties ◽  
Natural Rubber ◽  
Mechanical Test ◽  
Polymer Nanocomposite ◽  
Dynamic Mechanical Properties ◽  
Filler Loading ◽  
Rubber Matrix ◽  
Dynamic Mechanical ◽  
Blending Method ◽  
Thermoplastic Natural Rubber

In this paper the polymer nanocomposite of nickel zinc (NiZn) ferrite nanoparticles incorporated into the thermoplastic natural rubber nanocomposite (TPNR) were prepared via melt blending method. The effect of different NiZn loading (2-10 wt%) on morphology, tensile and dynamic mechanical properties of the obtained composites was investigated. It was found that NiZn ferrite is well dispersed in the thermoplastic natural rubber matrix. The tensile results indicated that filler loading has improved the tensile strength and Youngs modulus of the nanocomposite. However, the elongation at break decreased with increasing the percentage of NiZn. Dynamic mechanical test showed that the highest storage modulus is at 8 wt% filler. Any further increment of the filler content leads to the formation of agglomerate hence affecting the properties. The Scanning electron micrograph (SEM) micrographs reveal aspect ratio and filler orientation in the TPNR matrix also strongly promoted interfacial adhesion between the filler and the matrix to control its properties.

scholarly journals Improvement of Thermal and Mechanical Properties of Vietnam Deproteinized Natural Rubber via Graft Copolymerization with Methyl Methacrylate

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Thi Nhan Nguyen ◽  
Hieu Nguyen Duy ◽  
Dung Tran Anh ◽  
Thuong Nghiem Thi ◽  
Thu Ha Nguyen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Natural Rubber ◽  
Methyl Methacrylate ◽  
Graft Copolymer ◽  
Graft Copolymerization ◽  
Graft Copolymers ◽  
Thermal And Mechanical Properties ◽  
H Nmr ◽  
Tert Butyl Hydroperoxide ◽  
Deproteinized Natural Rubber

In this study, we investigated the improvement of the thermal and mechanical properties of Vietnam deproteinized natural rubber (DPNR) via graft copolymerization of methyl methacrylate (MMA). The graft copolymerization was achieved successfully in latex stage using tert-butyl hydroperoxide (TBHPO) and tetra-ethylenepentamine (TEPA) as radical initiators at 30°C. By grafting with various MMA feeds and initiator concentration of 6.6×10−5 mol/g-rubber, the highest grafting efficiency and conversion were achieved at MMA of 15 wt.% per kg of rubber, 68% and 90%, respectively. The structure of grafted copolymers was characterized by 1H NMR, FTIR-ATR, and GPC, and thermal properties were investigated through DSC and TGA measurements. These showed that graft copolymers were more stable and rigid than DPNR. Storage modulus (G′) of graft copolymer was found to double that of DPNR, which contributed to the formation of graft copolymer. After sulfur vulcanization, the mechanical properties of DPNR-graft-PMMA, such as tensile strength, tear strength, and hardness, were improved significantly. Curing behaviors of the graft copolymers were found to be remarkably better than virgin DPNR.

Sign in / Sign up

Export Citation Format

Share Document