Phase Morphology, Thermal and Mechanical Properties of Compatibilized Nylon12/Natural Rubber Blends Using PS/MNR

2013 ◽  
Vol 844 ◽  
pp. 53-56
Author(s):  
Saravalee Saengthaveep ◽  
Sadhan C. Jana ◽  
Rathanawan Magaraphan
Keyword(s):  
Mechanical Properties ◽  
Natural Rubber ◽  
Moisture Absorption ◽  
Rubber Particle ◽  
Impact Resistance ◽  
Phase Morphology ◽  
Thermal And Mechanical Properties ◽  
Binary Blend ◽  
Polyamide 12 ◽  
The Impact

To produce a tough material for application demanding high impact resistance and low moisture absorption, melt blending of Nylon12 (Polyamide 12, PA12) and natural rubber (NR) was carried out in a brabender plasticorder at 210 °C with rotor speed of 70 rpm in the presence of polystyrene/maleated natural rubber (PS/MNR) blend as a compatibilizer. The effect of compatibilizer content (1, 3, 5, 7 and 10 phr) on phase morphology, thermal, and mechanical properties of [Nylon12/NR]/[PS/MNR] blends was investigated by using SEM, DSC, and Izod impact tester, respectively. The result revealed that PS/MNR blend improved the compatibility of Nylon12/NR blends efficiently due to the presence of amide linkage at the interfaces from the reaction between the reactive groups of MNR and the NH2 end groups of Nylon12 during mixing. A fine phase morphology (good dispersion and small dispersed phase size of NR domains in Nylon12 matrix) of [Nylon12/NR]/[PS/MNR] blends was observed at the optimum compatibilizer content of 7 phr, relating to the improvement of mechanical property. The impact energy of [Nylon12/NR]/[PS/MNR] blends was 503 J/m higher than that of neat Nylon12 (115 J/m) and Nylon12/NR binary blend (241 J/m) due to the toughening effect of rubber and proper morphology. The melting temperature of all blends did not change obviously from thermal analysis. However, the presence of rubber particle obstructed the crystallization of Nylon12 phase, leading to the decreasing of %crystallinity from 93% to around 70%.

Effect of surface treatment on moisture absorption, thermal, and mechanical properties of sisal fiber

2020 ◽  
pp. 152808372092477 ◽  
Author(s):  
Adane Dagnaw Gudayu ◽  
Leif Steuernagel ◽  
Dieter Meiners ◽  
Rotich Gideon
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Tensile Strength ◽  
Moisture Absorption ◽  
Natural Fibers ◽  
Alkaline Treatment ◽  
Automotive Application ◽  
Sisal Fiber ◽  
Thermal And Mechanical Properties ◽  
The Impact

Natural fibers are increasingly being used as composite reinforcement for both thermoplastic and thermoset resin, mainly for automotive application. Due to their hydrophilic nature, natural fibers have certain limitations during composite manufacture especially owing to their poor resin wettability, weak fiber–polymer interface, high moisture absorption, and being affected by high temperature in case of thermoplastic resin. This work investigates the impact of sisal fiber modification techniques on moisture absorption, thermal, and mechanical properties of the fiber. Four sisal fiber samples were prepared; untreated, alkaline treated, acetylated, and a combined alkaline-treated/acetylation samples. The samples were evaluated for their hygroscopic nature, thermal stability, and tensile properties. It is found that acetylation resulted in a reduction of moisture absorption of sisal fiber as the acetylated and alkaline-treated/acetylated samples recorded a decrease of 42% and 28%, respectively. Alkaline treatment increased the absorbency owing to the removal of hemicellulose and lignin. The thermogravimetric result revealed that alkaline treatment improved the thermal stability as the alkali-treated and alkali-treated/acetylated samples showed improvement in thermal properties. The acetylated sample resulted in a significant reduction in tensile strength. But, the results from tensile tests of the alkaline-treated samples showed an insignificant decrease in tensile strength and improvement in the modulus for all treated samples. Fourier-transform infrared and scanning electron microscopic analysis were included in the study to supplement the results with structural and microstructural changes. The effect of those treatments on the sisal–PET composite properties was studied and will be submitted in part 2 of the study.

Effect of Compounding Methods on Mechanical Properties of Poly(lactic acid)/Starch/Natural Rubber Blends

2013 ◽  
Vol 802 ◽  
pp. 144-148
Author(s):  
Jadsadaporn Chouaytan ◽  
Varaporn Tanrattanakul
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Natural Rubber ◽  
Impact Resistance ◽  
Natural Rubber Latex ◽  
Extrusion Process ◽  
Poly Lactic Acid ◽  
Air Cooling ◽  
Rubber Blends ◽  
The Impact

This study showed the effect of different compounding methods on the impact resistance and tensile properties of poly(lactic acid) blended with cassava starch and natural rubber latex. Poly(ethylene glycol) was used as a plasticizer. It was found that the compounding method was important for the derived mechanical properties of the blend. Furthermore, cooling method of the extrudate also affected the mechanical properties of the blends. The air cooling in the extrusion process provided higher mechanical properties than the water cooling. This work also showed the effect of the natural rubber in the PLA/starch blend.

Effect of combined drink cans and steel fibers on the impact resistance and mechanical properties of concrete

2020 ◽  
Vol 14 (2) ◽  
pp. 6734-6742
Author(s):  
A. Syamsir ◽  
S. M. Mubin ◽  
N. M. Nor ◽  
V. Anggraini ◽  
S. Nagappan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Impact Resistance ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Indirect Tensile ◽  
The Impact

This study investigated the combine effect of 0.2 % drink cans and steel fibers with volume fractions of 0%, 0.5%, 1%, 1.5%, 2%, 2.5% and 3% to the mechanical properties and impact resistance of concrete. Hooked-end steel fiber with 30 mm and 0.75 mm length and diameter, respectively was selected for this study.  The drinks cans fiber were twisted manually in order to increase friction between fiber and concrete. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the strength performance of concrete, especially the compressive strength, flexural strength and indirect tensile strength. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the compressive strength, flexural strength and indirect tensile strength by 2.3, 7, and 2 times as compare to batch 1, respectively. Moreover, the impact resistance of fiber reinforced concrete has increase by 7 times as compared to non-fiber concretes. Moreover, the impact resistance of fiber reinforced concrete consistently gave better results as compared to non-fiber concretes. The fiber reinforced concrete turned more ductile as the dosage of fibers was increased and ductility started to decrease slightly after optimum fiber dosage was reached. It was found that concrete with combination of 2% steel and 0.2% drink cans fibers showed the highest compressive, split tensile, flexural as well as impact strength.    

scholarly journals Effect of SWCNT-Tuball Paper on the Lightning Strike Protection of CFRPs and Their Selected Mechanical Properties

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3140
Author(s):  
Kamil Dydek ◽  
Anna Boczkowska ◽  
Rafał Kozera ◽  
Paweł Durałek ◽  
Łukasz Sarniak ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Copper Foil ◽  
Impact Resistance ◽  
Mechanical Analysis ◽  
Lightning Strike ◽  
Single Wall Carbon Nanotubes ◽  
Carbon Fibre Reinforced Polymer ◽  
The Impact

The main aim of this work was the investigation of the possibility of replacing the heavy metallic meshes applied onto the composite structure in airplanes for lightning strike protection with a thin film of Tuball single-wall carbon nanotubes in the form of ultra-light, conductive paper. The Tuball paper studied contained 75 wt% or 90 wt% of carbon nanotubes and was applied on the top of carbon fibre reinforced polymer before fabrication of flat panels. First, the electrical conductivity, impact resistance and thermo-mechanical properties of modified laminates were measured and compared with the reference values. Then, flat panels with selected Tuball paper, expanded copper foil and reference panels were fabricated for lightning strike tests. The effectiveness of lightning strike protection was evaluated by using the ultrasonic phased-array technique. It was found that the introduction of Tuball paper on the laminates surface improved both the surface and the volume electrical conductivity by 8800% and 300%, respectively. The impact resistance was tested in two directions, perpendicular and parallel to the carbon fibres, and the values increased by 9.8% and 44%, respectively. The dynamic thermo-mechanical analysis showed higher stiffness and a slight increase in glass transition temperature of the modified laminates. Ultrasonic investigation after lightning strike tests showed that the effectiveness of Tuball paper is comparable to expanded copper foil.

scholarly journals Effects of Phase Morphology on Mechanical Properties: Oriented/Unoriented PP Crystal Combination with Spherical/Microfibrillar PET Phase

Polymers ◽  
2019 ◽  
Vol 11 (2) ◽  
pp. 248 ◽  
Author(s):  
Dashan Mi ◽  
Yingxiong Wang ◽  
Maja Kuzmanovic ◽  
Laurens Delva ◽  
Yixin Jiang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Ethylene Terephthalate ◽  
Phase Morphology ◽  
Mechanical Recycling ◽  
Immiscible Blends ◽  
Poly Ethylene Terephthalate ◽  
Poly Ethylene ◽  
The Impact

In situ microfibrillation and multiflow vibrate injection molding (MFVIM) technologies were combined to control the phase morphology of blended polypropylene (PP) and poly(ethylene terephthalate) (PET), wherein PP is the majority phase. Four kinds of phase structures were formed using different processing methods. As the PET content changes, the best choice of phase structure also changes. When the PP matrix is unoriented, oriented microfibrillar PET can increase the mechanical properties at an appropriate PET content. However, if the PP matrix is an oriented structure (shish-kebab), only the use of unoriented spherical PET can significantly improve the impact strength. Besides this, the compatibilizer polyolefin grafted maleic anhydride (POE-g-MA) can cover the PET in either spherical or microfibrillar shape to form a core–shell structure, which tends to improve both the yield and impact strength. We focused on the influence of all composing aspects—fibrillation of the dispersed PET, PP matrix crystalline morphology, and compatibilized interface—on the mechanical properties of PP/PET blends as well as potential synergies between these components. Overall, we provided a theoretical basis for the mechanical recycling of immiscible blends.

Morphology and Mechanical Properties of Natural Rubber-PCL Core-Shell/PLA Composites

2013 ◽  
Vol 747 ◽  
pp. 745-748
Author(s):  
Warangkhana Phromma ◽  
Rathanawan Magaraphan
Keyword(s):  
Mechanical Properties ◽  
Natural Rubber ◽  
Core Shell ◽  
Dynamic Mechanical Analyzer ◽  
Admicellar Polymerization ◽  
Twin Screw ◽  
Impact Tester ◽  
The Impact ◽  
Pendulum Impact ◽  
Pendulum Impact Tester

Natural rubber (NR)/Polycaprolactone (PCL) core-shell (NR-ad-PCL), from admicellar polymerization, was as an impact modifier for the composites. PLA was mixed with NR-ad-PCL with different NR-ad-PCL contents at 5, 10, 15 and 20 wt%. PLA-based composites were prepared by co-rotating twin screw extruder. The morphology of the composites was observed by Field emission scanning electron microscope (FE-SEM). Mechanical properties of the composites were investigated by dynamic mechanical analyzer and pendulum impact tester. The impact strength of the PLA filled with NR-ad-PCL increased while modulus of the PLA composites decreased with increasing rubber contents.

scholarly journals Morpho-Structural, Thermal and Mechanical Properties of PLA/PHB/Cellulose Biodegradable Nanocomposites Obtained by Compression Molding, Extrusion, and 3D Printing

Nanomaterials ◽  
2019 ◽  
Vol 10 (1) ◽  
pp. 51 ◽  
Author(s):  
Adriana Nicoleta Frone ◽  
Dan Batalu ◽  
Ioana Chiulan ◽  
Madalina Oprea ◽  
Augusta Raluca Gabor ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Interfacial Adhesion ◽  
Compression Molding ◽  
Processing Technique ◽  
Single Step ◽  
Thermal And Mechanical Properties ◽  
Reactive Blending ◽  
Scanning Calorimetry ◽  
The Impact

Biodegradable blends and nanocomposites were produced from polylactic acid (PLA), poly(3-hydroxybutyrate) (PHB) and cellulose nanocrystals (NC) by a single step reactive blending process using dicumyl peroxide (DCP) as a cross-linking agent. With the aim of gaining more insight into the impact of processing methods upon the morphological, thermal and mechanical properties of these nanocomposites, three different processing techniques were employed: compression molding, extrusion, and 3D printing. The addition of DCP improved interfacial adhesion and the dispersion of NC in nanocomposites as observed by scanning electron microscopy and atomic force microscopy. The carbonyl index calculated from Fourier transform infrared spectroscopy showed increased crystallinity after DCP addition in PLA/PHB and PLA/PHB/NC, also confirmed by differential scanning calorimetry analyses. NC and DCP showed nucleating activity and favored the crystallization of PLA, increasing its crystallinity from 16% in PLA/PHB to 38% in DCP crosslinked blend and to 43% in crosslinked PLA/PHB/NC nanocomposite. The addition of DCP also influenced the melting-recrystallization processes due to the generation of lower molecular weight products with increased mobility. The thermo-mechanical characterization of uncross-linked and cross-linked PLA/PHB blends and nanocomposites showed the influence of the processing technique. Higher storage modulus values were obtained for filaments obtained by extrusion and 3D printed meshes compared to compression molded films. Similarly, the thermogravimetric analysis showed an increase of the onset degradation temperature, even with more than 10 °C for PLA/PHB blends and nanocomposites after extrusion and 3D-printing, compared with compression molding. This study shows that PLA/PHB products with enhanced interfacial adhesion, improved thermal stability, and mechanical properties can be obtained by the right choice of the processing method and conditions using NC and DCP for balancing the properties.

Sign in / Sign up

Export Citation Format

Share Document