scholarly journals Composites from Thermoplastic Natural Rubber Reinforced Rubberwood Sawdust: Effects of Sawdust Size and Content on Thermal, Physical, and Mechanical Properties

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Chatree Homkhiew ◽  
Surasit Rawangwong ◽  
Worapong Boonchouytan ◽  
Wiriya Thongruang ◽  
Thanate Ratanawilai
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
High Density Polyethylene ◽  
High Performance ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Shore Hardness ◽  
Thermoplastic Natural Rubber ◽  
Plastic Content

The aim of this work is to investigate the effects of rubberwood sawdust (RWS) size and content as well as the ratio of natural rubber (NR)/high-density polyethylene (HDPE) blend on properties of RWS reinforced thermoplastic natural rubber (TPNR) composites. The addition of RWS about 30–50 wt% improved the modulus of the rupture and tensile strength of TPNR composites blending with NR/HDPE ratios of 60/40 and 50/50. TPNR composites reinforced with RWS 80 mesh yielded better tensile strength and modulus of rupture than the composites with RWS 40 mesh. The TPNR/RWS composites with larger HDPE content gave higher tensile, flexural, and Shore hardness properties and thermal stability as well as lower water absorption. The TPNR/RWS composites with larger plastic content were therefore suggested for applications requiring high performance of thermal, physical, and mechanical properties.

Physical and Mechanical Properties of Thermoplastic Natural Rubber (TPNR) Nanocomposites

2012 ◽  
Vol 576 ◽  
pp. 394-397 ◽  
Author(s):  
Noor Azlina Hassan ◽  
Hassan Norita ◽  
Sahrim Haji Ahmad ◽  
Rozaidi Rasid ◽  
Hazleen Anuar ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Maleic Anhydride ◽  
Natural Rubber ◽  
Physical And Mechanical Properties ◽  
Melt Blending ◽  
Mixing Parameters ◽  
Blending Method ◽  
Thermoplastic Natural Rubber ◽  
Internal Mixer

Thermoplastic natural rubber (TPNR) nanocomposites were prepared by melt blending method with the optimum mixing parameters (140oC, 100 rpm, 12 min) using internal mixer (Haake 600 P). The aim of this work is to study the effects of organo-montmorillonite (OMMT) on the physical and mechanical properties of TPNR with and without coupling agent (maleic anhydride grafted polyethylene, MA-PE). Significant improvement in tensile strength and modulus of TPNR nanocomposites were obtained with the presence of MA-PE.

EFFECT OF ZINC DITHIOCARBAMATES AND THIAZOLE-BASED ACCELERATORS ON THE VULCANIZATION OF NATURAL RUBBER

2012 ◽  
Vol 85 (1) ◽  
pp. 120-131 ◽  
Author(s):  
Md. Najib Alam ◽  
Swapan Kumar Mandal ◽  
Subhas Chandra Debnath
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
High Performance Liquid Chromatography ◽  
Liquid Chromatography ◽  
Reaction Mechanism ◽  
Natural Rubber ◽  
High Performance ◽  
Binary Systems ◽  
Synergistic Activity ◽  
Tetramethylthiuram Disulfide

Abstract Several zinc dithiocarbamates (ZDCs) as accelerator derived from safe amine has been exclusively studied in the presence of thiazole-based accelerators to introduce safe dithiocarbamate in the vulcanization of natural rubber. Comparison has been made between conventional unsafe zinc dimethyldithiocarbamate (ZDMC) with safe novel ZDC combined with thizole-based accelerators in the light of mechanical properties. The study reveals that thiuram disulfide and 2-mercaptobenzothiazole (MBT) are always formed from the reaction either between ZDC and dibenzothiazyledisulfide (MBTS) or between ZDC and N-cyclohexyl-2-benzothiazole sulfenamide (CBS). It has been conclusively proved that MBT generated from MBTS or CBS reacts with ZDC and produces tetramethylthiuram disulfide. The observed synergistic activity has been discussed based on the cure and physical data and explained through the results based on high-performance liquid chromatography and a reaction mechanism. Synergistic activity is observed in all binary systems studied. The highest tensile strength is observed in the zinc (N-benzyl piperazino) dithiocarbamate-accelerated system at 3:6 mM ratios. In respect of tensile strength and modulus value, unsafe ZDMC can be successfully replaced by safe ZDCs in combination with thiazole group containing accelerator.

SIFAT FISIK MEKANIK PAPAN PARTIKEL TANPA PEREKAT DARI TANDAN KOSONG KELAPA SAWIT (Elaeis Guineensis acq)

2014 ◽  
Vol 6 (1) ◽  
pp. 15 ◽  
Author(s):  
Budi Tri Cahyana
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Water Content ◽  
Oil Palm ◽  
Modulus Of Elasticity ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Particle Board ◽  
Thickness Swelling ◽  
Empty Fruit Bunches

This research aimed to get the physical and mechanical properties of non adhesive-particle board from oil palm empty fruit bunches. The oil palm empty fruit bunches were degradated to fibre and boiled in boiling water during 60 minute then dried in ± 2 weeks. The dried raw material was chopped to be fibre in 5 mesh, 10 mesh, and 16 mesh. It were complied into a mold and then hot pressed in 35 kgf/cm2 pressure during 10 minute with 3 of temperature variety, 160°C, 180°C and 200°C. The result showed that the average of particle board water content was 7,11 -  9,85 % and the density was 0,63 – 0,76 gr/cm3. The highest thickness swelling was 22,59 % in 10 mesh and 160 0C (a2b1) temperature of oil palm empty fruit bunches. The modulus of rupture was 211,67 kg/cm2  in 10 mesh and 180 0C (a2b2) temperature. The modulus of elasticity was 490,85 kg/cm2 in 10 mesh and 160 0C (a2b1) temperature. The tensile strength was 7,49 kg/cm2 in 5 mesh and 200 0C (a1b3) temperature. The average of physical and mechanical properties such as water content, density, modulus of rupture, tensile strength were fulfill the SNI requirement, while the average of thickness swelling and modulus of elasticity were not fulfill the SNI requirement.Keywords: oil palm empty fruit bunches, particle board

scholarly journals Characterisation of Physical and Mechanical Properties of Unthinned and Unpruned Plantation-Grown Eucalyptus nitens H.Deane & Maiden Lumber

Forests ◽  
2019 ◽  
Vol 10 (2) ◽  
pp. 194 ◽  
Author(s):  
Mohammad Derikvand ◽  
Nathan Kotlarewski ◽  
Michael Lee ◽  
Hui Jiao ◽  
Gregory Nolan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Shear Strength ◽  
Moisture Content ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Eucalyptus Nitens ◽  
Linear Regression Models ◽  
Bending Modulus ◽  
Small Wood

The use of fast-growing plantation eucalypt (i.e., pulpwood eucalypt) in the construction of high-value structural products has received special attention from the timber industry in Australia and worldwide. There is still, however, a significant lack of knowledge regarding the physical and mechanical properties of the lumber from such plantation resources as they are mainly being managed to produce woodchips. In this study, the physical and mechanical properties of lumber from a 16-year-old pulpwood Eucalyptus nitens H.Deane & Maiden resource from the northeast of Tasmania, Australia was evaluated. The tests were conducted on 318 small wood samples obtained from different logs harvested from the study site. The tested mechanical properties included bending modulus of elasticity (10,377.7 MPa) and modulus of rupture (53 MPa), shear strength parallel (5.5 MPa) and perpendicular to the grain (8.5 MPa), compressive strength parallel (42.8 MPa) and perpendicular to the grain (4.1 MPa), tensile strength perpendicular to the grain (3.4 MPa), impact bending (23.6 J/cm2), cleavage (1.6 kN) and Janka hardness (23.2 MPa). Simple linear regression models were developed using density and moisture content to predict the mechanical properties. The variations in the moisture content after conventional kiln drying within randomly selected samples in each test treatment were not high enough to significantly influence the mechanical properties. A relatively high variation in the density values was observed that showed significant correlations with the changes in the mechanical properties. The presence of knots increased the shear strength both parallel and perpendicular to the grain and significantly decreased the tensile strength of the lumber. The results of this study created a profile of material properties for the pulpwood E. nitens lumber that can be used for numerical modelling of any potential structural product from such a plantation resource.

The Effect of Citric Acid on the Mechanical Properties of Thermoplastic Tapioca Starch/High Density Polyethylene/Natural Rubber Blends

2014 ◽  
Vol 679 ◽  
pp. 292-299
Author(s):  
Mohamad Kahar Ab Wahab ◽  
H. Ismail ◽  
N.Z. Noriman ◽  
H. Kamarudin ◽  
A.M. Mustafa Al Bakri
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Citric Acid ◽  
Natural Rubber ◽  
High Density Polyethylene ◽  
High Density ◽  
Elongation At Break ◽  
Tapioca Starch ◽  
Rubber Blends ◽  
Mechanical And Physical Properties

Effects of citric acid on the mechanical properties of thermoplastic tapioca starch/high density polyethylene/natural rubber (HDPE/NR/TPS) blends were investigated. The ratio between HDPE/NR was fixed at 70/30 and used as a matrix system. TPS loadings with and without modification with citric acid (CA) were varied from 0% to 30wt%. Mechanical and physical properties of blends were evaluated as a function of TPS loadings modified with and without CA. The tensile strength, Young’s modulus and elongation at break were found to decrease with increasing TPS content. However an improvement in the tensile strength for TPS modified with CA at 5%, 10% and 20% TPS loadings was observed. The degree of TPS adhesion and dispersion in HDPE/NR blends were determined by scanning electron microscope (SEM).Keywords; HDPE/NR/TPS, citric acid, tensile properties, morphology.

scholarly journals Enhanced Physical and Mechanical Properties of Nitrile-Butadiene Rubber Composites with N-Cetylpyridinium Bromide-Carbon Black

Molecules ◽  
2021 ◽  
Vol 26 (4) ◽  
pp. 805
Author(s):  
Egor A. Kapitonov ◽  
Natalia N. Petrova ◽  
Vasilii V. Mukhin ◽  
Leonid A. Nikiforov ◽  
Vladimir D. Gogolev ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Carbon Black ◽  
Physical And Mechanical Properties ◽  
Butadiene Rubber ◽  
Volumetric Wear ◽  
Shore Hardness ◽  
Cetylpyridinium Bromide ◽  
Rubber Composites ◽  
Nitrile Butadiene Rubber

The physical and mechanical properties of nitrile–butadiene rubber (NBR) composites with N-cetylpyridinium bromide-carbon black (CPB-CB) were investigated. Addition of 5 parts per hundred rubber (phr) of CPB-CB into NBR improved the tensile strength by 124%, vulcanization rate by 41%, shore hardness by 15%, and decreased the volumetric wear by 7% compared to those of the base rubber-CB composite.

Effect of TiO2 Nanofillers on Mechanical Properties of PVC/ENR/TiO2 Nanocomposites

2014 ◽  
Vol 911 ◽  
pp. 105-109 ◽  
Author(s):  
Nur Azrini Ramlee ◽  
C.T. Ratnam ◽  
N.H. Alias ◽  
T.A. Tengku Mohd
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Uv Light ◽  
Research Work ◽  
Physical And Mechanical Properties ◽  
Shore Hardness ◽  
Long Term Stability ◽  
Insignificant Difference ◽  
Irradiation Dose Rate

Addition of nanoparticles currently in polymer blends has brought tremendous transformation in polymer engineering field. Incorporation of TiO2 nanofillers is believed to enhance the physical and mechanical properties of PVC/ENR blends due to its excellent characteristics including non-toxicity, long term stability and UV light discoloration resistance. The main objective of this research work is to introduce titanium dioxide (TiO2) nanofillers in a range of 0 - 6 phr into polyvinyl chloride (PVC) and epoxidized natural rubber (ENR) blends. Modification on mechanical properties of PVC/ENR blends has successfully been carried via irradiation crosslinking technique. The addition of TiO2 nanofillers has improved the tensile strength and hardness of the nanocomposites. Nevertheless, at higher loading of 6 phr, the results obviously showed an insignificant difference of performances for both tensile strength and shore hardness properties. Upon radiation of 50 kGy, the increase in Ts of the PVC/ENR blends with addition of 4 phr TiO2 was found to be optimum before the Ts value drops with higher exposure to irradiation dose rate. Gel fraction of irradiated PVC/ENR/TiO2 nanocomposites indicates the nanocomposites are crosslinked upon electron beam irradiation. Degree of crosslink was also increased with the addition of 4 phr and 6 phr TiO2.

Study on Gypsum-Bonded Particleboard Reinforced with Jute Fibres

Holzforschung ◽  
2002 ◽  
Vol 56 (4) ◽  
pp. 440-445 ◽  
Author(s):  
Y. Deng ◽  
T. Furuno
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
Untreated Wood ◽  
Physical And Mechanical Properties ◽  
Fiber Content ◽  
Modulus Of Rupture ◽  
Thickness Swelling ◽  
Jute Fibers ◽  
Low Weight ◽  
Wood Particles

Summary This paper deals with the influence of length and content (based on a percentage of wood particles) of jute fibers on the physical and mechanical properties of gypsum-bonded particleboard (GPB). The length and amount of jute fibers had a significant effect on the internal bond strength (IB) and the modulus of rupture (MOR) of GPB. The addition of jute fibers did not obviously influence the modulus of elasticity (MOE), the thickness swelling (TS) or water absorption (WA). The values of IB were prominently high at the 3 mm length and 9–12% contents of jute fibers. The highest value of MOR was attained when the board was made with fibers 12 mm in length and a fiber content of 15%. The optimal amount of jute fibers reinforced the mechanical properties of GPB to achieve high performance. However, too much jute fiber reduced the IB, MOR (except for 12 mm length), and MOE of GPB. The values of TS and WA decreased gradually with an increase in the fiber content for all fiber lengths. In addition, the GPB gave very low weight loss on exposure to wood-decaying fungi of both Tyromyces palustris (TYP) and Coriolus versicolor (COV) as compared with untreated wood. It was concluded that the combination of 3 mm length and 9–12% content or 12 mm length and 15% content of jute fibers was the optimum for producing good performance of

scholarly journals Cross-Linked Chitosan as an Eco-Friendly Binder for High-Performance Wood-Based Fiberboard

2021 ◽  
Vol 2021 ◽  
pp. 1-7
Author(s):  
Erzhuo Huang ◽  
Yanwei Cao ◽  
Xinpeng Duan ◽  
Yutao Yan ◽  
Zhe Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Dimensional Stability ◽  
High Performance ◽  
Physical And Mechanical Properties ◽  
High Strength ◽  
Modulus Of Rupture ◽  
Wood Fibers ◽  
Promising Candidate ◽  
Pressing Method ◽  
Optimum Modulus

High-performance wood-based fiberboards with high strength and dimensional stability were fabricated by hot-pressing method using 2,5-dimethoxy-2,5-dihydrofuran (DHF) cross-linked chitosan (CS) as an eco-friendly binder. The effects of cross-linked chitosan on the mechanical properties and dimensional stability of wood-based fiberboards were investigated. It is evident that cross-linked chitosan addition was effective in improving mechanical properties and dimensional stability of wood-based fiberboards. The prepared wood-based fiberboard bonded by DHF cross-linked CS displayed optimum modulus of rupture (MOR) of 42.1 MPa, modulus of elasticity (MOE) of 3986.0 MPa, internal bonding (IB) strength of 1.4 MPa, and thickness swelling (TS) value of 16.3%. The improvement of physical and mechanical properties of wood-based fiberboards could be attributed to the amide linkages and hydrogen bonds between wood fibers and cross-linked chitosan. The high-performance wood-based fiberboards fabricated in this study may be a promising candidate for eco-friendly wood-based composites.

Sign in / Sign up

Export Citation Format

Share Document