scholarly journals A Bayesian Approach to the Eagar–Tsai Model for Melt Pool Geometry Prediction with Implications in Additive Manufacturing of Metals

2021 ◽  
Author(s):  
Brendan J. Whalen ◽  
Ji Ma ◽  
Prasanna V. Balachandran
Keyword(s):  
Additive Manufacturing ◽  
Bayesian Approach ◽  
Melt Pool

scholarly journals Additive Manufacturing of Bulk Nanocrystalline FeNdB Based Permanent Magnets

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 538
Author(s):  
Dagmar Goll ◽  
Felix Trauter ◽  
Timo Bernthaler ◽  
Jochen Schanz ◽  
Harald Riegel ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Melt Spinning ◽  
Permanent Magnets ◽  
Maximum Energy ◽  
Laser Melting ◽  
Powder Bed ◽  
Melt Pool ◽  
Bulk Nanocrystalline ◽  
Ribbon Structures ◽  
Nanocrystalline Ribbon

Lab scale additive manufacturing of Fe-Nd-B based powders was performed to realize bulk nanocrystalline Fe-Nd-B based permanent magnets. For fabrication a special inert gas process chamber for laser powder bed fusion was used. Inspired by the nanocrystalline ribbon structures, well-known from melt-spinning, the concept was successfully transferred to the additive manufactured parts. For example, for Nd16.5-Pr1.5-Zr2.6-Ti2.5-Co2.2-Fe65.9-B8.8 (excess rare earth (RE) = Nd, Pr; the amount of additives was chosen following Magnequench (MQ) powder composition) a maximum coercivity of µ0Hc = 1.16 T, remanence Jr = 0.58 T and maximum energy density of (BH)max = 62.3 kJ/m3 have been achieved. The most important prerequisite to develop nanocrystalline printed parts with good magnetic properties is to enable rapid solidification during selective laser melting. This is made possible by a shallow melt pool during laser melting. Melt pool depths as low as 20 to 40 µm have been achieved. The printed bulk nanocrystalline Fe-Nd-B based permanent magnets have the potential to realize magnets known so far as polymer bonded magnets without polymer.

Accelerating Large-Format Metal Additive Manufacturing: How Controls R&D Is Driving Speed, Scale, and Efficiency

2020 ◽  
Author(s):  
Brian T. Gibson ◽  
Paritosh Mhatre ◽  
Michael C. Borish ◽  
Justin L. West ◽  
Emma D. Betters ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Large Scale ◽  
Closed Loop ◽  
Size Control ◽  
Pool Size ◽  
Large Format ◽  
Layer Height ◽  
Melt Pool ◽  
The Impact ◽  
Melt Pool Size

Abstract This article highlights work at Oak Ridge National Laboratory’s Manufacturing Demonstration Facility to develop closed-loop, feedback control for laser-wire based Directed Energy Deposition, a form of metal Big Area Additive Manufacturing (m-BAAM), a process being developed in partnership with GKN Aerospace specifically for the production of Ti-6Al-4V pre-forms for aerospace components. A large-scale structural demonstrator component is presented as a case-study in which not just control, but the entire 3D printing workflow for m-BAAM is discussed in detail, including design principles for large-format metal AM, toolpath generation, parameter development, process control, and system operation, as well as post-print net-shape geometric analysis and finish machining. In terms of control, a multi-sensor approach has been utilized to measure both layer height and melt pool size, and multiple modes of closed-loop control have been developed to manipulate process parameters (laser power, print speed, deposition rate) to control these variables. Layer height control and melt pool size control have yielded excellent local (intralayer) and global (component-level) geometry control, and the impact of melt pool size control in particular on thermal gradients and material properties is the subject of continuing research. Further, these modes of control have allowed the process to advance to higher deposition rates (exceeding 7.5 lb/hr), larger parts (1-meter scale), shorter build times, and higher overall efficiency. The control modes are examined individually, highlighting their development, demonstration, and lessons learned, and it is shown how they operate concurrently to enable the printing of a large-scale, near net shape Ti-6Al-4V component.

A deep neural network for classification of melt-pool images in metal additive manufacturing

2018 ◽  
Vol 31 (2) ◽  
pp. 375-386 ◽  
Author(s):  
Ohyung Kwon ◽  
Hyung Giun Kim ◽  
Min Ji Ham ◽  
Wonrae Kim ◽  
Gun-Hee Kim ◽  
...  
Keyword(s):  
Neural Network ◽  
Additive Manufacturing ◽  
Deep Neural Network ◽  
Metal Additive Manufacturing ◽  
Melt Pool ◽  
Metal Additive

Wire arc additive manufacturing of Invar parts: bead geometry and melt pool monitoring

Measurement ◽  
2021 ◽  
pp. 110452
Author(s):  
Fernando Veiga ◽  
Alfredo Suarez ◽  
Eider Aldalur ◽  
Teresa Artaza
Keyword(s):  
Additive Manufacturing ◽  
Bead Geometry ◽  
Melt Pool ◽  
Wire Arc Additive Manufacturing

New Hammerstein Modeling and Analysis for Controlling Melt Pool Width in Powder Bed Fusion Additive Manufacturing

2021 ◽  
pp. 1-7
Author(s):  
Dan Wang ◽  
Xinyu Zhao ◽  
Xu Chen
Keyword(s):  
Finite Element ◽  
Additive Manufacturing ◽  
Process Variations ◽  
Element Model ◽  
Hammerstein Model ◽  
Powder Bed Fusion ◽  
Modeling And Analysis ◽  
Powder Bed ◽  
Melt Pool ◽  
Linearized Model

Abstract Despite the advantages and emerging applications, broader adoption of powder bed fusion (PBF) additive manufacturing is challenged by insufficient reliability and in-process variations. Finite element modeling and control-oriented modeling have been identified fundamental for predicting and engineering part qualities in PBF. This paper first builds a finite element model (FEM) of the thermal fields to look into the convoluted thermal interactions during the PBF process. Using the FEM data, we identify a novel surrogate system model from the laser power to the melt pool width. Linking a linearized model with a memoryless nonlinear submodel, we develop a physics-based Hammerstein model that captures the complex spatiotemporal thermomechanical dynamics. We verify the accuracy of the Hammerstein model using the FEM and prove that the linearized model is only a representation of the Hammerstein model around the equilibrium point. Along the way, we conduct the stability and robustness analyses and formalize the Hammerstein model to facilitate the subsequent control designs.

Multiaxis wire and arc additive manufacturing for overhangs based on conical substrates

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Fusheng Dai ◽  
Shuaifeng Zhang ◽  
Runsheng Li ◽  
Haiou Zhang
Keyword(s):  
Principal Component Analysis ◽  
Additive Manufacturing ◽  
Design Methodology ◽  
Principal Component ◽  
Deposition Process ◽  
Content Type ◽  
Melt Pool ◽  
Planning Approach ◽  
Intelligent Approach ◽  
Supporting Structures

Purpose This paper aims to present a series of approaches for three-related issues in multiaxis in wire and arc additive manufacturing (WAAM) as follows: how to achieve a stable and robust deposition process and maintain uniform growth of the part; how to maintain consistent formation of a melt pool on the surface of the workpiece; and how to fabricate an overhanging structure without supports. Design/methodology/approach The principal component analysis-based path planning approach is proposed to compute the best scanning directions of slicing contours for the generation of filling paths, including zigzag paths and parallel skeleton paths. These printing paths have been experimented with in WAAM. To maintain consistent formation of a melt pool at overhanging regions, the authors introduce definitions for the overhanging point, overhanging distance and overhanging vector, with which the authors can compute and optimize the multiaxis motion. A novel fabricating strategy of depositing the overhanging segments as a support for the deposition of filling paths is presented. Findings The second principal component of a planar contour is a reasonable scanning direction to generate zigzag filling paths and parallel skeleton filling paths. The overhanging regions of a printing layer can be supported by pre-deposition of overhanging segments. Large overhangs can be successfully fabricated by the multiaxis WAAM process without supporting structures. Originality/value An intelligent approach of generating zigzag printing paths and parallel skeleton printing paths. Optimizations of depositing zigzag paths and parallel skeleton paths. Applications of overhanging point overhanging distance and overhanging vector for multiaxis motion planning. A novel fabricating strategy of depositing the overhanging segments as a support for the deposition of filling paths.

scholarly journals An Overview of Additive Manufacturing Technologies—A Review to Technical Synthesis in Numerical Study of Selective Laser Melting

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3895 ◽  
Author(s):  
Abbas Razavykia ◽  
Eugenio Brusa ◽  
Cristiana Delprete ◽  
Reza Yavari
Keyword(s):  
Numerical Simulation ◽  
Additive Manufacturing ◽  
Selective Laser Melting ◽  
Powder Bed Fusion ◽  
Laser Melting ◽  
Powder Bed ◽  
Part Quality ◽  
Melt Pool ◽  
Wide Range ◽  
Am Processes

Additive Manufacturing (AM) processes enable their deployment in broad applications from aerospace to art, design, and architecture. Part quality and performance are the main concerns during AM processes execution that the achievement of adequate characteristics can be guaranteed, considering a wide range of influencing factors, such as process parameters, material, environment, measurement, and operators training. Investigating the effects of not only the influential AM processes variables but also their interactions and coupled impacts are essential to process optimization which requires huge efforts to be made. Therefore, numerical simulation can be an effective tool that facilities the evaluation of the AM processes principles. Selective Laser Melting (SLM) is a widespread Powder Bed Fusion (PBF) AM process that due to its superior advantages, such as capability to print complex and highly customized components, which leads to an increasing attention paid by industries and academia. Temperature distribution and melt pool dynamics have paramount importance to be well simulated and correlated by part quality in terms of surface finish, induced residual stress and microstructure evolution during SLM. Summarizing numerical simulations of SLM in this survey is pointed out as one important research perspective as well as exploring the contribution of adopted approaches and practices. This review survey has been organized to give an overview of AM processes such as extrusion, photopolymerization, material jetting, laminated object manufacturing, and powder bed fusion. And in particular is targeted to discuss the conducted numerical simulation of SLM to illustrate a uniform picture of existing nonproprietary approaches to predict the heat transfer, melt pool behavior, microstructure and residual stresses analysis.

A Comparative Study Between Selective Laser Melting and Electron Beam Additive Manufacturing Based on Thermal Modeling

2018 ◽  
Author(s):  
M. Shafiqur Rahman ◽  
Paul J. Schilling ◽  
Paul D. Herrington ◽  
Uttam K. Chakravarty
Keyword(s):  
Electron Beam ◽  
Additive Manufacturing ◽  
Heat Source ◽  
Selective Laser Melting ◽  
Thermal Modeling ◽  
Maximum Temperature ◽  
Full Density ◽  
Rate Variation ◽  
Laser Melting ◽  
Melt Pool

Selective Laser Melting (SLM) and Electron Beam Additive Manufacturing (EBAM) are two of the most promising additive manufacturing technologies that can make full density metallic components using layer-by-layer fabrication methods. In this study, three-dimensional computational fluid dynamics models with Ti-6Al-4V powder were developed to conduct numerical simulations of both the SLM and EBAM processes. A moving conical volumetric heat source with Gaussian distribution and temperature-dependent thermal properties were incorporated in the thermal modeling of both processes. The melt-pool geometry and its thermal behavior were investigated numerically and results for temperature profile, cooling rate, variation in specific heat, density, thermal conductivity, and enthalpy were obtained with similar heat source specifications. Results obtained from the two models at the same maximum temperature of the melt pool were then compared to describe their deterministic features to be considered for industrial applications. Validation of the modeling was performed by comparing the EBAM simulation results with the EBAM experimental results for melt pool geometry.

Sign in / Sign up

Export Citation Format

Share Document