scholarly journals Mechanical properties of self-compacting high-performance concrete with fly ash and silica fume

2019 ◽  
Vol 2 (1) ◽  
Author(s):  
A. M. Falmata ◽  
A. Sulaiman ◽  
R. N. Mohamed ◽  
A. U. Shettima
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Silica Fume ◽  
High Performance ◽  
High Performance Concrete

Influence of Different Curing Days on Mechanical Properties of Concrete with Admixtures of Fly Ash, Blast Furnace Slag and Silica Fume

2013 ◽  
Vol 405-408 ◽  
pp. 2843-2846
Author(s):  
Jeong Eun Kim ◽  
Wan Shin Park ◽  
Sun Woong Kim ◽  
Do Gyeum Kim ◽  
Myung Sug Cho ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Silica Fume ◽  
Blast Furnace Slag ◽  
High Performance ◽  
High Performance Concrete ◽  
Furnace Slag

High performance concrete (HPC) can be made with cement alone or any combination of cement and mineral components, such as, blast furnace slag, fly ash, silica fume, kaolin, rice husk ash, and fillers, such as limestone powder [. In this study, three mixes of high performance concrete (HPC) with same water-binder ratio and different types of mineral admixtures were prepared. he compressive strength, splitting tensile strength and modulus of elasticity values were measured in accordance with the ASTM. The influence of fly ash (FA), blast furnace slag (BS) and silica fume (SF) on mechanical properties of HPC were compared and analyzed. Their mechanical properties are measured at 7 days and 28 days. The results showed that specimen BS45+SF5 performed better than specimens BS30+FA25+SF5 and BS65+SF5 for the compressive strength, splitting tensile strength and modulus of elasticity.

An Experimental Study on Mechanical Properties for Ternary High Performance Concrete with Fly-Ash, Blast Furnace Slag, Silica Fume

2012 ◽  
Vol 204-208 ◽  
pp. 3699-3702
Author(s):  
Jeong Eun Kim ◽  
Wan Shin Park ◽  
Sung Ho Cho ◽  
Do Gyeum Kim ◽  
Jea Myoung Noh
Keyword(s):  
Mechanical Properties ◽  
Blast Furnace ◽  
Fly Ash ◽  
Silica Fume ◽  
Blast Furnace Slag ◽  
High Performance ◽  
High Performance Concrete ◽  
Heat Of Hydration ◽  
Concrete Crack ◽  
Furnace Slag

It is essential that concrete component is made up with aggregate, sand, cement and water. But recently, Public concern is increasing of a variety structure, resource recycle. Also, According to heat of hydration rising, Concrete is making a causative of concrete-crack. Concrete-crack causes a falling-off in quality of concrete. Therefore, high-performance concrete is evaluated by concrete mechanical properties (compressive strength, splitting tensile strength) with different admixture (fixing W/B 34%), fly ash, blast furnace slag, and silica fume replacement ratio (50%, 50%, and 25%).

Effect of Fly Ash, Silica Fume and Blast Furnace Slag on Mechanical Property of High Performance Concrete

2013 ◽  
Vol 372 ◽  
pp. 243-246 ◽  
Author(s):  
Nam Yong Eom ◽  
Wan Shin Park ◽  
Jeong Eun Kim ◽  
Sun Woong Kim ◽  
Do Gyeum Kim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Property ◽  
Blast Furnace ◽  
Fly Ash ◽  
Silica Fume ◽  
Blast Furnace Slag ◽  
High Performance ◽  
High Performance Concrete ◽  
Mineral Admixture ◽  
Furnace Slag

The use of mineral admixture such as fly ash, blast furnace slag and silica fume in making high performance concrete has increased. The objective of this study is to investigate mechanical properties of compressive strength, splitting tensile strength and modulus of elasticity of hardened high performance concrete.

High Performance Concrete with Ternary Binders

2018 ◽  
Vol 761 ◽  
pp. 120-123 ◽  
Author(s):  
Vlastimil Bílek ◽  
David Pytlík ◽  
Marketa Bambuchova
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Silica Fume ◽  
High Performance ◽  
Ordinary Portland Cement ◽  
High Performance Concrete ◽  
Fresh Concrete ◽  
Binder Ratio ◽  
Water To Binder Ratio ◽  
Condensed Silica Fume

Use a ternary binder for production of a high performance concrete with a compressive strengths between 120 and 170 MPa is presented. The water to binder ratio of the concrete is 0.225 and the binder is composed of Ordinary Portland Cement (OPC), condensed silica fume (CSF), ground limestone (L), fly ash (FA) and metakaoline (MK). The dosage of (M + CSF) is kept at a constant level for a better workability of fresh concrete. Different workability, flexural and compressive strengths were obtained for concretes with a constant cement and a metakaoline dosage, and for a constant dosage (FA + L) but a different ratio FA / L. An optimum composition was found and concretes for other tests were designed using this composition.

The Effect of Homogenization Procedure on Mechanical Properties of High-Performance Concrete with Partial Replacement of Cement by Supplementary Cementitious Materials

2019 ◽  
Vol 292 ◽  
pp. 102-107 ◽  
Author(s):  
Josef Fládr ◽  
Petr Bílý ◽  
Karel Šeps ◽  
Roman Chylík ◽  
Vladimír Hrbek
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Water Content ◽  
High Performance ◽  
High Performance Concrete ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Partial Replacement ◽  
Depth Of Penetration ◽  
Cement Additive

High-performance concrete is a very specific type of concrete. Its production is sensitive to both the quality of compounds used and the order of addition of particular compounds during the homogenization process. The mechanical properties were observed for four dosing procedures of each of the three tested concrete mixtures. The four dosing procedures were identical for the three mixes. The three mixes varied only in the type of supplementary cementitious material used and in water content. The water content difference was caused by variable k-value of particular additives. The water-to-binder ratio was kept constant for all the concretes. The additives used were metakaolin, fly ash and microsilica. The comparison of particular dosing procedures was carried out on the values of basic mechanical properties of concrete. The paper compares compressive strength and depth of penetration of water under pressure. Besides the comparsion of macro-mechanical properties, the effect of microsilica and fly ash additives on micro-mechanical properties was observed with the use of scanning electron microscopy (SEM) and nanoindentation data analysis. Nanoindentation was used to determine the thickness and strength of interfacial transition zone (ITZ) for different sequence of addition of cement, additive and aggregate. The thickness obtained by nanoindentation was further investigated by SEM EDS line scanning.

scholarly journals Effect of different curing conditions on the mechanical properties of reactive powder concrete

2018 ◽  
Vol 162 ◽  
pp. 02014
Author(s):  
Mazin Abdulrahman ◽  
Alyaa Al-Attar ◽  
Marwa Ahmad
Keyword(s):  
Mechanical Properties ◽  
Silica Fume ◽  
High Performance ◽  
High Performance Concrete ◽  
Material Constant ◽  
Hot Water ◽  
Modulus Of Rupture ◽  
Reactive Powder Concrete ◽  
Curing Conditions ◽  
Reactive Powder

Reactive Powder Concrete (RPC) is an ultra-high performance concrete which has superior mechanical and physical properties, and composed of cement and very fine powders such as quartz sand and silica fume with very low water/ binder ratio and Superplasticizer. Heat treatment is a well-known method that can further improve the performance of (RPC). The current research including an experimental study of the effect of different curing conditions on mechanical properties of reactive powder concrete (compressive strength, modulus of rupture and splitting tensile strength), the curing conditions includes three type of curing; immersion in water at temperature of 35 OC (which is considered as the reference-curing situation), immersion in water at temperature of 90 OC for 5 hours daily and curing with hot steam for 5 hours daily) until 28 days according to ASTM C684-99 [8]. This research includes also the study of effect of adding silica fume as percentage of cement weight on mechanical properties of reactive powder concrete for different percentage ratios (5%,10% and 15%). Super plasticizer is also used with ratio of (1.8%) by weight of cementitious material; constant water cement ratio (0.24) was used for all mixes. For each reactive concrete mix, it has been cast into a cubes of (150*150*150) (to conduct the compression test), a cylinders of 150mm diameter with 300mm height (to conduct split test) and prisms of (500*100*100)mm to conduct the modulus of rupture test. The results showed that the best method of curing (according to its enhancing the RPC mechanical properties) is the method of immersion in hot water at temperature 90 OC for the all silica fume percentages, and the best used silica fume percentage was (10%) for the all used curing methods.

Sign in / Sign up

Export Citation Format

Share Document