The effect of processing parameters and material properties on residual forces induced in Laser Powder Bed Fusion (L-PBF)

2021 ◽  
pp. 102192
Author(s):  
R. Magana-Carranza ◽  
C.J. Sutcliffe ◽  
E.A. Patterson
Keyword(s):  
Material Properties ◽  
Processing Parameters ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed

scholarly journals Optimizing Laser Powder Bed Fusion Parameters for IN-738LC by Response Surface Method

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4879
Author(s):  
Mireia Vilanova ◽  
Rubén Escribano-García ◽  
Teresa Guraya ◽  
Maria San Sebastian
Keyword(s):  
Response Surface ◽  
Response Surface Method ◽  
Process Parameters ◽  
Crack Density ◽  
Processing Parameters ◽  
Optimum Process ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Surface Method

A method to find the optimum process parameters for manufacturing nickel-based superalloy Inconel 738LC by laser powder bed fusion (LPBF) technology is presented. This material is known to form cracks during its processing by LPBF technology; thus, process parameters have to be optimized to get a high quality product. In this work, the objective of the optimization was to obtain samples with fewer pores and cracks. A design of experiments (DoE) technique was implemented to define the reduced set of samples. Each sample was manufactured by LPBF with a specific combination of laser power, laser scan speed, hatch distance and scan strategy parameters. Using the porosity and crack density results obtained from the DoE samples, quadratic models were fitted, which allowed identifying the optimal working point by applying the response surface method (RSM). Finally, five samples with the predicted optimal processing parameters were fabricated. The examination of these samples showed that it was possible to manufacture IN738LC samples free of cracks and with a porosity percentage below 0.1%. Therefore, it was demonstrated that RSM is suitable for obtaining optimum process parameters for IN738LC alloy manufacturing by LPBF technology.

scholarly journals A Review of Factors Affecting the Mechanical Properties of Maraging Steel 300 Fabricated via Laser Powder Bed Fusion

Metals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1273 ◽  
Author(s):  
Barry Mooney ◽  
Kyriakos Kourousis
Keyword(s):  
Mechanical Properties ◽  
Maraging Steel ◽  
Processing Parameters ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Factors Affecting ◽  
Powder Bed ◽  
Porosity Defects ◽  
Research Findings ◽  
Microstructure Density

Maraging steel is an engineering alloy which has been widely employed in metal additive manufacturing. This paper examines manufacturing and post-processing factors affecting the properties of maraging steel fabricated via laser powder bed fusion (L-PBF). It covers the review of published research findings on how powder quality feedstock, processing parameters, laser scan strategy, build orientation and heat treatment can influence the microstructure, density and porosity, defects and residual stresses developed on L-PBF maraging steel, with a focus on the maraging steel 300 alloy. This review offers an evaluation of the resulting mechanical properties of the as-built and heat-treated maraging steel 300, with a focus on anisotropic characteristics. Possible directions for further research are also identified.

scholarly journals Effects of Positioning Conditions on Material Properties In Powder bed Fusion Additive Manufacturing

2021 ◽  
Author(s):  
Mevlüt Yunus Kayacan ◽  
Nihat Yılmaz
Keyword(s):  
Additive Manufacturing ◽  
Material Properties ◽  
Layer By Layer ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Cooling Rates ◽  
Powder Bed ◽  
Manufacturing Technologies ◽  
Average Size ◽  
Hardness Values

Abstract Among additive manufacturing technologies, Laser Powder Bed Fusion (L-PBF) is considered the most widespread layer-by-layer process. Although the L-PBF, which is also called as SLM method, has many advantages, several challenging problems must be overcome, including part positioning issues. In this study, the effect of part positioning on the microstructure of the part in the L-PBF method was investigated. Five Ti6Al4V samples were printed in different positions on the building platform and investigated with the aid of temperature, porosity, microstructure and hardness evaluations. In this study, martensitic needles were detected within the microstructure of Ti6Al4V samples. Furthermore, some twins were noticed on primary martensitic lines and the agglomeration of β precipitates was observed in vanadium rich areas. The positioning conditions of samples were revealed to have a strong effect on temperature gradients and on the average size of martensitic lines. Besides, different hardness values were attained depending on sample positioning conditions. As a major result, cooling rates were found related to positions of samples and the location of point on the samples. Higher cooling rates and repetitive cooling cycles resulted in microstructures becoming finer and harder.

Evaluation of the Material Properties of the Ti and CoCr Alloys Prepared by Laser Powder Bed Fusion

2020 ◽  
Vol 985 ◽  
pp. 223-228
Author(s):  
Jana Bidulská ◽  
Róbert Bidulský ◽  
Patrik Petrouse ◽  
Tibor Kvačkaj ◽  
Marco Actis Grande ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Image Analysis ◽  
Additive Manufacturing ◽  
Material Properties ◽  
Ti6al4v Alloy ◽  
Homogeneous Distribution ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Quantitative Image

The main aim of the present paper is evaluated the mechanical properties, microstructures and porosity of Ti6Al4V and CoCrW alloys produced by Laser Powder Bed Fusion (L-PBF) as an additive manufacturing (AM) technology. The mechanical properties were follows: For Ti6Al4V alloy the UTS was 1180 MPa; the YS was in the range <600; 745 MPa>. For CoCrW alloys, the UTS were in range <750; 950 MPa> and YS was in range <400; 500>. Evaluation of porosity was realized on non-etched samples using by quantitative image analysis in order to describe the dimensional and morphological porosity characteristics. The pores in the Ti6Al4V alloy showed homogeneous distribution without significant large pores.

Sign in / Sign up

Export Citation Format

Share Document