Structure of biomimetic apatite grown on hydroxyapatite (HA)

2020 ◽  
Vol 46 (18) ◽  
pp. 28806-28813
Author(s):  
N. Vargas-Becerril ◽  
D.A. Sánchez-Téllez ◽  
L. Zarazúa-Villalobos ◽  
D.M. González-García ◽  
M.A. Álvarez-Pérez ◽  
...  
Keyword(s):  
Author(s):  
Federica Bertolotti ◽  
Francisco J. Carmona ◽  
Gregorio Dal Sasso ◽  
Gloria B. Ramírez-Rodríguez ◽  
José Manuel Delgado-López ◽  
...  

2005 ◽  
Vol 59 (11) ◽  
pp. 1352-1355 ◽  
Author(s):  
D.A. Cortes ◽  
A.A. Nogiwa ◽  
J.M. Almanza ◽  
S. Ortega

2018 ◽  
Vol 115 (27) ◽  
pp. E6135-E6144 ◽  
Author(s):  
Melika Sarem ◽  
Miriam Heizmann ◽  
Andrea Barbero ◽  
Ivan Martin ◽  
V. Prasad Shastri

In adult bone injuries, periosteum-derived mesenchymal stem/stromal cells (MSCs) form bone via endochondral ossification (EO), whereas those from bone marrow (BM)/endosteum form bone primarily through intramembranous ossification (IMO). We hypothesized that this phenomenon is influenced by the proximity of MSCs residing in the BM to the trabecular bone microenvironment. Herein, we investigated the impact of the bone mineral phase on human BM-derived MSCs’ choice of ossification pathway, using a biomimetic bone-like hydroxyapatite (BBHAp) interface. BBHAp induced hyperstimulation of extracellular calcium-sensing receptor (CaSR) and temporal down-regulation of parathyroid hormone 1 receptor (PTH1R), leading to inhibition of chondrogenic differentiation of MSCs even in the presence of chondroinductive factors, such as transforming growth factor-β1 (TGF-β1). Interestingly rescuing PTH1R expression using human PTH fragment (1–34) partially restored chondrogenesis in the BBHAp environment. In vivo studies in an ectopic site revealed that the BBHAp interface inhibits EO and strictly promotes IMO. Furthermore, CaSR knockdown (CaSR KD) disrupted the bone-forming potential of MSCs irrespective of the absence or presence of the BBHAp interface. Our findings confirm the expression of CaSR in human BM-derived MSCs and unravel a prominent role for the interplay between CaSR and PTH1R in regulating MSC fate and the choice of pathway for bone formation.


2006 ◽  
Vol 11-12 ◽  
pp. 235-238
Author(s):  
El-Sayed Ghaith ◽  
Toshihiro Kasuga ◽  
Masayuki Nogami

Amorphous calcium silicate coating on a metallic titanium substrate for hard tissue replacement was prepared by a sol-gel method. Calcium silicate film was deposited on a titanium substrate by a spin-coating technique and subsequently heated at 500°C for 2 h in air. The deposited film, which was dense, had thickness of about 800 nm and strongly adhered to the substrate. Biomimetic apatite-forming ability of the deposited films was examined by soaking in simulated body fluid (SBF). Thin film X-ray diffractometry and scanning electron microscopy showed the formation of apatite on the surface after 10 days of soaking in SBF.


2005 ◽  
Vol 40 (13) ◽  
pp. 3509-3515 ◽  
Author(s):  
D. A. Cortés ◽  
A. Medina ◽  
S. Escobedo ◽  
M. A. López

2008 ◽  
Vol 34 (5) ◽  
pp. 1139-1144 ◽  
Author(s):  
Daqing Wei ◽  
Yu Zhou ◽  
Dechang Jia ◽  
Yaming Wang

2016 ◽  
pp. 223 ◽  
Author(s):  
Takahiro Ogawa ◽  
Makiko Saita ◽  
Takayuki Ikeda ◽  
Masahiro Yamada ◽  
Katsuhiko Kimoto ◽  
...  

2007 ◽  
Vol 534-536 ◽  
pp. 1617-1620 ◽  
Author(s):  
J. Kim ◽  
Y.C. Choi ◽  
Hyoung Seop Kim ◽  
Sun Ig Hong

Biomimetic apatite deposition behaviors and mechanical performance for as-rolled and annealed Ni-Ti plates were investigated. Apatite nucleation and growth on Ni-Ti in SBF (simulated body fluid) was not appreciably influenced by heat treatment. But, the apatite deposition rate increased slightly by NaOH surface treatment. The nodular apatite on the deposited layer is favored on a macro-scale since the surface energy of polycrystalline apatite particles can be reduced by forming nodules. The weight gain after apatite deposition for Ni-Ti (0.004 g/cm2) after 10 days were found to be smaller that that of NaOH treated Ti-6Al-4V, but it was comparable to that of non- NaOH-treated Ti-6Al-4V (0.004 g/cm2). The stress-strain responses of annealed Ni-Ti displayed the pseudoelastic behavior associated with stress-induced martensite formation with the transition stress for the martensite formation equal to 320 MPa. On the other hand the cold worked Ni-Ti displayed no appreciable pseudoelastic region and the yield stress was ~500MPa. A good biomimetic apatite formation and excellent mechanical performance of Ni-Ti suggests that Ni-Ti can be an excellent candidate material for orthopedic implants.


Sign in / Sign up

Export Citation Format

Share Document