Effects of HCl hydrolyzed cellulose nanocrystals from waste papers on the Hydroxypropyl methylcellulose/Cationic Starch biofilms

ABSTRACT The study reports on the preparation of nanocrystalline cellulose from waste papers (WPNCC), as an environmental friendly approach of source material and investigation of their effects on the morphological, mechanical and barrier properties of the Hydroxypropyl methylcellulose/Cationic starch (HPMC/CS) nanocomposites. HCl hydrolysis followed by alkali treatment and deinking of the fibers resulted in the production of WPNCC. The TEM results confirmed the rod like shape of WPNCC; the average diameter was 22± 7 nanometers and the length was 125± 25 nanometers. The hydrolysis yield was 65% with high crystallinity index of 79.6%. The results of X-ray diffraction confirmed the successfully production of WPNCC and their effective presence in the HPMC/CS matrix. The homogeneity of WPNCC dispersion in the polymer matrix was approved by FESEM analysis. The WPNCC also did not affect the nanocomposites optical clarity. The optimum amount of 9 wt% WPNCC, showed the highest barrier, mechanical and biodegradablility properties.

Synthesis of porous γ-Fe2O3 from scorodite synthesized using ultrasound irradiation and evaluation of its battery performance

The effect of 200 kHz ultrasound on scorodite synthesis at 70 °C and 3 h reaction conditions was investigated using sulfuric acidic solutions of various pH (3.0, 2.0, 1.5, 1.0, and 0.0). In contrast to the case of only O2 gas flow without ultrasound irradiation, oxidizing radicals generated by ultrasound irradiation promote Fe(II) oxidation in solution and precursor, allowing scorodite to synthesize with high crystallinity (>99%), which relates to low solubility, even in strong acid solution at pH 1.0. During synthesis, particle shape was changed to polyhedral or spindle type depending on the pH of 0.0 to 3.0. The spindle-shaped scorodite was probably formed by the decrease of precursor amount produced in initial stage of the synthesis. Furthermore, porous maghemite obtained by alkali treatment of scorodite showed initial discharge capacities of 146 mAh/g (polyhedron) and 167 mAh/g (spindle), indicating that its potential use as a cathode material for lithium-ion batteries.

Immunomodulatory Properties and Osteogenic Activity of Polyetheretherketone Coated with Titanate Nanonetwork Structures

Polyetheretherketone (PEEK) is a potential substitute for conventional metallic biomedical implants owing to its superior mechanical and chemical properties, as well as biocompatibility. However, its inherent bio-inertness and poor osseointegration limit its use in clinical applications. Herein, thin titanium films were deposited on the PEEK substrate by plasma sputtering, and porous nanonetwork structures were incorporated on the PEEK surface by alkali treatment (PEEK-TNS). Changes in the physical and chemical characteristics of the PEEK surface were analyzed to establish the interactions with cell behaviors. The osteoimmunomodulatory properties were evaluated using macrophage cells and osteoblast lineage cells. The functionalized nanostructured surface of PEEK-TNS effectively promoted initial cell adhesion and proliferation, suppressed inflammatory responses, and induced macrophages to anti-inflammatory M2 polarization. Compared with PEEK, PEEK-TNS provided a more beneficial osteoimmune environment, including increased levels of osteogenic, angiogenic, and fibrogenic gene expression, and balanced osteoclast activities. Furthermore, the crosstalk between macrophages and osteoblast cells showed that PEEK-TNS could provide favorable osteoimmunodulatory environment for bone regeneration. PEEK-TNS exhibited high osteogenic activity, as indicated by alkaline phosphatase activity, osteogenic factor production, and the osteogenesis/osteoclastogenesis-related gene expression of osteoblasts. The study establishes that the fabrication of titanate nanonetwork structures on PEEK surfaces could extract an adequate immune response and favorable osteogenesis for functional bone regeneration. Furthermore, it indicates the potential of PEEK-TNS in implant applications.

Prospective long-term evaluation of incomplete distal renal tubular acidosis in idiopathic calcium nephrolithiasis diagnosed (treated) by low-dose NH4CL loading – gender prevalences and impact of alkali treatment

Purpose Prospective evaluation of the prevalence of incomplete distal renal tubular acidosis (idRTA) in idiopathic calcium stone formers (ICSF) diagnosed by half-dose ammonium chloride loading (NH4Cl, 0.05 g/kg body weight/day) and impact of alkali treatment of idRTA. Methods Evaluation of 386 consecutive idiopathic calcium stone formers (ICSF) (280 males, 106 females) for idRTA. If screening fasting urine pH was > 5.80, 1-day NH4Cl loading was performed without severe adverse effects. Normally, urine pH falls below 5.45. Results Sixty-four idiopathic calcium stone formers exhibited idRTA, one complete dRTA. Prevalence was higher in women (25.4%) than in men (13.6%). Thus, for more equilibrated comparisons, we formed pairs of 62 idiopathic calcium stone formers (ICSF) with and 62 without idRTA, matched for gender, age, BMI and serum creatinine. Idiopathic calcium stone formers with idRTA more often had hypercalciuria (p < 0.025) and urine citrate < 2 mmol/d (p < 0.05), formed calcium phosphate stones more frequently, exhibited higher numbers of stones/year (1.4 ± 1.5 vs. 0.9 ± 0.8, p = 0.034) and 2.5 times more intrarenal calcifications (4.6 ± 5.9 vs. 1.8 ± 3.6, p = 0.002). All idiopathic calcium stone formers with idRTA were recommended chronic alkali therapy. After 4–15 years of follow-up, stone events /years follow-up (stone passage or urologic intervention) were higher in patients non-adherent to alkali therapy (0.61 ± 0.92) than in patients adherent to treatment (0.11 ± 0.21, p = 0.006). Conclusion Incomplete distal renal tubular acidosis is 1.8-fold more prevalent among female idiopathic calcium stone formers, predicts more stone recurrences, predisposes to calcium phosphate stones and is associated with 2.5 times more intrarenal calcifications vs. non-idRTA patients. Chronic alkali treatment reduces clinical stone recurrences by 5.5 times. Graphical abstract

Influence of Alkali Treatment and Maleated Polypropylene (MAPP) Compatibilizer on the Dry-Sliding Wear and Frictional Behavior of Borassus Fruit Fine Fiber (BFF)/Polypropylene (PP) Polymer Composites for Various Engineering Applications

Tribological properties of the novel Borassus fruit fine fiber- (BFF-) reinforced polypropylene (PP) composites with respect to fiber matrix surface modifications have been described. Composites were fabricated by an injection molding process using Borassus fruit fine fiber (BFF) of 5 wt.% as reinforcement and polypropylene (PP) as a matrix component. Fibers were treated with alkali (T) to remove the residual lignin (if present) and to enhance the interfacial adhesion between the fiber/matrix interface. Alkali treatment reveals additional reactive functional groups here on the surface of the Borassus fiber, allowing effective interaction bonding with the polypropylene matrix. Borassus fibers are primarily treated with an alkali solution to extract weaker unstructured amorphous constituents so that the fibers retain crystallized components, thereby strengthening the fiber’s strength. A 5 wt.% of maleated polypropylene (MAPP) was used as a compatibilizer to improve the interfacial adhesion between fiber and the polymer matrix. The wear and frictional behavior of BFF/PP composites with respect to the modifications were evaluated by steel counterface utilizing pin-on-disc test contraption under dry-sliding conditions. The sliding velocity, applied load, and sliding distance were maintained as 2.198 m/s, 9.81–29.43 N, and 4000 m, respectively. The results demonstrate that the reinforcement of BFF to polypropylene matrix and the modifications improved the wear properties of the neat polymer matrix. Findings concluded that the abrasive wear resistance of T + PP + MAPP composite showed better interfacial adhesion and bonding, thus resulting in better tribological performance as compared to the other three compositions under different loading conditions. The effective substantial improvement of the coefficient of friction has been observed in alkali-treated fiber and polypropylene matrix with MAPP compatibilizer (T + PP + MAPP) composites due to the presence of MAPP compatibilizer and alkali-treated fibers. The frictional coefficient of T + PP + MAPP possesses better interfacial bonding strength upon NaOH treatment, and coupling agent, which results in enhancement of effective contact surface area and good surface friction characteristics, has been observed under different loading conditions. The fracture mechanism of worn-out portions of BFF/PP composites was studied using high-resolution scanning electron microscopy to analyze various imperfections like debonding, splits, fiber cracks, and wreckage or fragments formation.

Fabrication and Experimental Analysis of Treated Snake Grass Fiber Reinforced with Polyester Composite

The selection of fiber is predominant for natural fiber-reinforced polymer composite materials, which should have easy extraction and good bonding with considerable strength. In this paper, some chemical treatments were done on the fiber material to increase interfacial bonding between the snake grass fiber (Sansevieria ehrenbergii) and polyester matrix, such as alkali treatment (NaOH), potassium permanganate treatment, sodium carbonate treatment, hydrogen peroxide treatment, and calcium carbonate treatment. The chopped snake grass fiber-reinforced polymer composite material was prepared by keeping 25 wt.% of fiber and 30 mm fiber length reinforced with an unsaturated polyester resin that was cured with the help of the catalyst methyl ethyl ketone peroxide (MEPK). Cobalt naphthenate was used as an accelerator. Tribological properties were discussed for the highly potential sample with the help of a pin-on-disc wear tester, and the results were analysed by the Taguchi L9 orthogonal array. This paper exhibited the best mechanical and tribological properties among those chemical-treated fibers used in fiber-reinforced composite materials and untreated fibers used in fiber-reinforced composite materials. CaCO3 treatment provided higher tensile strength (45 MPa), impact strength (3.35 J), and hardness (27 BHN). Finally, the mechanical and tribological characterization of the samples was done with the aid of SEM (scanning electron microscope).

Microstructure Transformation In Palm-Fiber Cell Wall And Its Influence On the Fiber's Mechanical Properties During Alkali Treatment

In this study, we examined the microstructure transformation of palm fiber and the influence of this transformation on the fiber mechanical properties during alkali treatment. The fibers were treated with different concentrations of NaOH to study the change rules of the microstructure and the tensile properties. FT-IR microspectroscopic imaging and confocal laser scanning microscopy were adopted to observe microstructure transformation during alkali treatment. Research results showed that the hemicellulose and lignin in the fiber cell wall were removed by alkali treatment, leading to a rearrangement of cellulose chains. The tensile properties palm fibers were significantly improved because of crystallinity alterations in the cell walls after alkali treatment. This study might provide a basis for palm fiber’s high-value utilization in the field of materials.

A fabrication and characterization of luffa/PANI/PEO biocomposite nanofibers by means of electrospinning

Purpose This paper aims to address the production of biocomposite nanofibers using luffa natural fibers and polyaniline conductive polymer/polyethylene oxides (PANI/PEO). Design/methodology/approach In this study, luffa natural fibers are extracted by chemical method. After mixing the treated luffa (TL) with the PANI/PEO solution, TL/PANI/PEO nanofibers were produced by electrospinning (ES) method under different ES parameters to examine the optimal conditions for nanofiber production. Then TL/PANI/PEO biocomposite nanofibers prepared in different weight ratios were produced to analyze the effects of luffa in the morphology and thermal properties of the biocomposite nanofibers. The characterization analysis of TL/PANI/PEO biocomposite nanofibers was performed by scanning electron microscopy, Fourier transform infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC) analysis methods. Findings The analysis shows that different weight ratios of TL to PANI/PEO changed the morphology of the membrane. When increasing the weight ratio of TL, the morphological structure of TL/PANI/PEO transformed from nanofiber structure to thin film structure. The appearance of O—H peaks in the FTIR results proved the existence of TL in PANI/PEO nanofibers (membrane). Moreover, an increase in the weight ratio of luffa from 2% to 7.5% leads to an increase in the peak intensity of the O—H group. Regarding DSC analysis, biocomposite nanofibers improved the thermal properties. According to all results, 2%wt TL/PANI/PEO showed optimal morphological properties. Originality/value Plant cellulose was extracted from the luffa, one of the natural fibers, by method of alkali treatment. A new type of biocomposite nanofibers was produced using TL blend with PANI via electrospinning method.