Multiscale modeling of unsaturated flow of dual-scale fiber preform in liquid composite molding II: Non-isothermal flows

2012 ◽  
Vol 43 (1) ◽  
pp. 14-28 ◽  
Author(s):  
Hua Tan ◽  
Krishna M. Pillai
Keyword(s):  
Multiscale Modeling ◽  
Unsaturated Flow ◽  
Liquid Composite Molding ◽  
Fiber Preform ◽  
Composite Molding ◽  
Isothermal Flows ◽  
Dual Scale

First Steps Towards Quantitative Validation of the Unsaturated-Flow Theories in Liquid Composite Molding

2003 ◽  
Author(s):  
Tonmoy Roy ◽  
Baiju Z. Babu ◽  
Krishna M. Pillai
Keyword(s):  
Pore Volume ◽  
Unsaturated Flow ◽  
Volume Ratio ◽  
Mold Filling ◽  
Inlet Pressure ◽  
Liquid Composite Molding ◽  
Fiber Mats ◽  
Pressure History ◽  
Composite Molding ◽  
Dual Scale

In liquid composite molding technologies such as Resin Transfer Molding (RTM), a thermoset resin is injected into a mold cavity with a pre-placed preform made of fiber mats to create a cured part. In order to improve the physics of resin flow in dual-scale (woven, stitched or braided) fiber mats, the authors carried out many transient 1-D mold-filling experiments to investigate the onset of unsaturated flow through the inlet-pressure history. Their study revealed that the measured pressure history, which droops downwards for dual-scale fiber mats, is at a variance with the linear pressure profile predicted by state-of-the-art Liquid Composite Molding (LCM) mold-filling simulation physics. It was also observed that the drooping of the inlet pressure increases with an increase in the compression of fiber mats. In this paper, the correlation between a previously proposed dimensionless number pore volume ratio and the droop in the inlet pressure history has been sought. Studying the micrographs of composite samples, pore volume ratio is measured for various fiber mat compression. It is observed that the droop in the inlet pressure profiles increase with an increase in the pore volume ratio. This is the first attempt to quantitatively validate the previous theories on the unsaturated flow.

Experimental study of saturation by visible light transmission in dual-scale fibrous reinforcements during composite manufacturing

2017 ◽  
Vol 36 (23) ◽  
pp. 1693-1711 ◽  
Author(s):  
F LeBel ◽  
É Ruiz ◽  
F Trochu
Keyword(s):  
Visible Light ◽  
Light Transmission ◽  
Void Formation ◽  
In Situ Monitoring ◽  
Injection System ◽  
Computer Assisted ◽  
Liquid Composite Molding ◽  
Composite Molding ◽  
The Impact ◽  
Dual Scale

A new in situ monitoring strategy is proposed to study void formation during real-time impregnation of dual-scale fibrous reinforcements in liquid composite molding. Void content data from burn-off tests are used to calibrate a refractive index matching approach based on two optical principles: Beer–Lambert and Fresnel laws. Once calibrated, this approach based on visible light transmission is used to study the impact of key process parameters on the saturation footprint of dual-scale fibrous reinforcements during and after mold filling. The injection parameters investigated are the flow front velocity, the pressure distribution inside the mold cavity, the bleeding flow rate, and the mold packing pressure. The experimental setup is a computer-assisted injection system and a transparent resin transfer molding mold is used to perform unidirectional injections. A vinyl ester resin is injected through E-glass bidirectional non-crimp fabrics under various manufacturing conditions. This investigation not only confirms the decreasing trend in void formation by mechanical entrapment of air with the decrease in impregnation velocity, as it converges toward the optimal impregnation conditions for this fibrous reinforcement reported in previous studies, but it also brings insights on void dissolution and transport in liquid composite molding.

Flow-induced deformation of unidirectional carbon fiber preform during the mold filling stage in liquid composite molding process

2017 ◽  
Vol 52 (9) ◽  
pp. 1265-1277 ◽  
Author(s):  
Dong Gi Seong ◽  
Shino Kim ◽  
Moon Kwang Um ◽  
Young Seok Song
Keyword(s):  
High Speed ◽  
Volume Fraction ◽  
Orientation Angle ◽  
Mold Filling ◽  
Liquid Composite Molding ◽  
Fiber Preform ◽  
Molding Process ◽  
Controllable Factors ◽  
Composite Molding ◽  
Fiber Deformation

Liquid composite molding has been developed as a high-speed process for manufacturing automotive lightweight parts using new equipment that applies a high pressure for mixing and injection. One of the technical issues is the deformation of fiber preform during the process, which causes defects in the size, mechanical properties and appearance of the final products. In this study, two types of deformation in unidirectional fiber preform during the mold filling process are investigated, which are rigid body deformation and local deformation. Three important forces, namely friction, in-mold stiffness of fiber preform and resin flow, are measured to investigate the mechanism of the fiber deformation. The magnitude of the forces was compared at an instant, which influenced the types of fiber deformation. The effects of the orientation angle and the volume fraction of fiber preform and flow rate were investigated to identify controllable factors to prevent undesired deformation during the process.

Modeling void formation and unsaturated flow in liquid composite molding processes: a survey and review

2011 ◽  
Vol 30 (11) ◽  
pp. 957-977 ◽  
Author(s):  
Chung Hae Park ◽  
Lee Woo
Keyword(s):  
Unsaturated Flow ◽  
State Of The Art ◽  
Void Formation ◽  
Pressure Profile ◽  
Liquid Composite Molding ◽  
Simulation Studies ◽  
Apparent Permeability ◽  
Composite Molding ◽  
Unsaturated Flows ◽  
Key Parameter

In this study, we present a review of the modeling of void formation and unsaturated flow in liquid composite molding processes. We examine modeling efforts considering all the mechanisms involved such as void formation and transport, bubble compression, and gas dissolution. In particular, the capillary number is identified as a key parameter for void formation and transport. Numerical simulation studies are reviewed, and a state-of-the-art is presented. The influence of microvoids on the global resin flow is also investigated. To model the unsaturated flow more accurately, we suggest considering the surface tension or capillary pressure, variation in permeability in terms of saturation and fiber displacement, as well as tow saturation. From this investigation, the apparent permeability and pressure profile in saturated and unsaturated flows are compared.

Sign in / Sign up

Export Citation Format

Share Document