Unconfined compressive strength and ductility of fiber-reinforced cemented sand

2011 ◽  
Vol 25 (2) ◽  
pp. 1134-1138 ◽  
Author(s):  
Sung-Sik Park
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Fiber Reinforced ◽  
Cemented Sand ◽  
Strength And Ductility

scholarly journals Mechanical Behavior of Cemented Sand Reinforced with Different Polymer Fibers

2019 ◽  
Vol 2019 ◽  
pp. 1-10 ◽  
Author(s):  
Xiangfeng Lv ◽  
Xiaohui Yang ◽  
Hongyuan Zhou ◽  
Shuo Zhang
Keyword(s):  
Compressive Strength ◽  
Mechanical Behavior ◽  
Brittle Failure ◽  
Unconfined Compressive Strength ◽  
Polypropylene Fiber ◽  
Ductile Failure ◽  
Polymer Fibers ◽  
Chemical Compositions ◽  
Peak Strain ◽  
Cemented Sand

In this study, the specimens of cemented sand were prepared by reinforcing it separately with different contents (0.5%, 1.0%, 1.5%, and 2.0%) of three different polymer fibers (polyamide, polyester, and polypropylene) prepared as filaments of different lengths (6, 9, and 12 mm). Then, these specimens were tested, and the improvement effects of the three fibers on the engineering-mechanical behavior of the cemented sand were analyzed and compared. The different microstructures and chemical compositions of the fiber-reinforced cemented sand specimens were investigated using electron microscopy and X-ray diffraction. Compression tests were performed to obtain the stress-strain curves of the specimens. Comparative analysis was performed on the variation patterns of the mechanical parameters (such as unconfined compressive strength and peak strain) of the specimens. Quantitative analysis was performed on the effect of fiber content and fiber filament length on the failure mode of the specimens. It was shown that the inclusion of fibers led to a change from brittle failure to ductile failure. The macro- and microexperimental results revealed that polypropylene fiber had the best improvement effect on the mechanical behavior of the cemented sand, followed by polyester fiber and polyamide fiber. In particular, the cemented sand specimen reinforced with 1.5% polypropylene fiber prepared as 9 mm length filaments had a brittleness index of 0.0578, exhibited ductile failure (in contrast to the brittle failure of the nonreinforced cemented sand), and yielded the highest unconfined compressive strength and shear strength among the specimens.

Characterization of a cemented sand with the pulse-velocity method

2006 ◽  
Vol 43 (3) ◽  
pp. 294-309 ◽  
Author(s):  
Zahid Khan ◽  
Anwar Majid ◽  
Giovanni Cascante ◽  
D Jean Hutchinson ◽  
Parsa Pezeshkpour
Keyword(s):  
Compressive Strength ◽  
Water Content ◽  
Wave Velocity ◽  
Unconfined Compressive Strength ◽  
Void Ratio ◽  
Cement Content ◽  
Pulse Velocity ◽  
Initial Water Content ◽  
Strain Property ◽  
Cemented Sand

The effect of variation in cement content, initial water content, void ratio, and curing time on wave velocity (low-strain property) and unconfined compressive strength (large-strain property) of a cemented sand is examined in this paper. The measured pulse velocity is compared with predictions made using empirical and analytical models, which are mostly based on the published results of resonant column tests. All specimens are made by mixing silica sand and gypsum cement (2.5–20% by weight) and tested under atmospheric pressure. The wave velocity reaches a maximum at optimum water content, and it is mostly affected by the number of cemented contacts; whereas compressive strength is governed not only by the number of contacts but also by the strength of contacts. Experimental relationships are developed for wave velocity and unconfined compressive strength as functions of cement content and void ratio. Available empirical models underpredict the wave velocity (60% on average), likely because of the effect of microfractures induced by confinement during the testing. Wave velocity is found to be a good indicator of cement content and unconfined compressive strength for the conditions of this study.Key words: wave velocity, low-strain stiffness, cemented sands, elastic moduli, unconfined compressive strength.

scholarly journals Experimental Study on Unconfined Compressive Strength of Basalt Fiber Reinforced Clay Soil

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Lei Gao ◽  
Guohui Hu ◽  
Nan Xu ◽  
Junyi Fu ◽  
Chao Xiang ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Clay Soil ◽  
Soil Column ◽  
Basalt Fiber ◽  
Dry Density ◽  
Fiber Reinforced ◽  
Maximum Dry Density ◽  
Sem Images ◽  
Reinforced Clay

In order to study the mechanism and effect of basalt fiber reinforced clay soil, a series of unconfined compressive strength tests conducted on clay soil reinforced with basalt fiber have been performed under the condition of optimum water content and maximum dry density. Both the content and length of basalt fiber are considered in this paper. When the effect of content is studied, the 12 mm long fibers are dispersed into clay soil at different contents of 0.05%, 0.1%, 0.15%, 0.20%, 0.25%, 0.30%, and 0.35%. When the effect of length is researched, different lengths of basalt fibers with 4 mm, 8 mm, 12 mm, and 15 mm are put into soil at the same content of 0.05%. Experimental results show that basalt fiber can effectively improve the UCS of clay soil. And the best content and length are 0.25% and 12 mm, respectively. The results also show that the basalt fiber reinforced clay soil has the “poststrong” characteristic. About the reinforcement mechanism, the fiber and soil column-net model is proposed in this paper. Based on this model and SEM images, the effect of fiber content and length is related to the change of fiber-soil column and formation of effective fiber-soil net.

Sign in / Sign up

Export Citation Format

Share Document