Interfacial mechanics of steel fibers in a High-Strength Fiber-Reinforced Self Compacting Concrete

2021 ◽  
Vol 301 ◽  
pp. 124344
Author(s):  
Carlos A. Benedetty ◽  
Pablo Augusto Krahl ◽  
Luiz Carlos Almeida ◽  
Leandro Mouta Trautwein ◽  
Gustavo Henrique Siqueira ◽  
...  
Author(s):  
Saad Al-Taan ◽  
Abduljalil Aldoski

The paper presents test results on 20 high-strength fiber reinforced concrete square columns subjected to concentric and eccentric loading. The study aim was to examine the effect of the weight of steel fibers on the strength and behavior of HSC columns under concentric and eccentric loading. All columns were longitudinally reinforced with 4 GFRP bars 6 mm diameter, and two steel bars 10 mm diameter, making the reinforcement ratio (ρg = 0.0181), and steel ties at 64 mm spacing. The studied test variables included the steel fiber weight ratio and the eccentricity. To prevent premature spalling in the concrete cover, it was discovered that it helps to add steel fibers to HSC mixtures in concrete columns. In addition, this also increases the strength of eccentrically loaded reinforced columns compared to that for concentrically loaded columns. The strength and behavior were predicted also by the proposed method. The predicted and the experimental results found to be in a good agreement.


Crystals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 91
Author(s):  
Sallal R. Abid ◽  
Murali Gunasekaran ◽  
Sajjad H. Ali ◽  
Ahmed L. Kadhum ◽  
Thaar S. Al-Gasham ◽  
...  

The self-compacting concrete (SCC) was invented to overcome the compaction problems in deep sections, owing to its perfect workability characteristics. Steel fibers when used with SCC would affect the required fluidity characteristics but improve its impact resistance. In this research, an experimental work was conducted to evaluate the impact response of micro-steel fiber-reinforced SCC, under flexural impact. A 5.47 kg free-falling mass was dropped repeatedly from 100 mm height on the top center of 270 mm-length beam specimens. Eight mixtures with two design grades of 30 and 50 MPa were prepared to distinguish the normal and high-strength SCCs. The distinguishing variable for each design grade was the fiber content, where four volumetric contents of 0%, 0.5%, 0.75%, and 1.0% were used. The test results showed that the impact resistance and ductility were significantly improved due to the incorporation of micro-steel fibers. The percentage improvements were noticeably higher at failure stage than at cracking stage. For the 30 MPa mixtures, the maximum percentage improvements at cracking and failure stages were 543% and 836%, respectively. Weibull’s linear correlations with R2 values of 0.84 to 0.97 were obtained at the failure stage, which meant that the impact failure number followed the Wiebull distribution.


2016 ◽  
Vol 5 (2) ◽  
pp. 32
Author(s):  
LOHITHA V ◽  
KRISHNESWAR R ◽  
KUMAR B. NARENDRA ◽  
◽  
◽  
...  

Buildings ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 63
Author(s):  
Anna L. Mina ◽  
Michael F. Petrou ◽  
Konstantinos G. Trezos

The scope of this paper is to investigate the performance of ultra-high performance fiber reinforced concrete (UHPFRC) concrete slabs, under projectile impact. Mixture performance under impact loading was examined using bullets with 7.62 mm diameter and initial velocity 800 m/s. The UHPFRC, used in this study, consists of a combination of steel fibers of two lengths: 6 mm and 13 mm with the same diameter of 0.16 mm. Six composition mixtures were tested, four UHPFRC, one ultra-high performance concrete (UHPC), without steel fibers, and high strength concrete (HSC). Slabs with thicknesses of 15, 30, 50, and 70 mm were produced and subjected to real shotgun fire in the field. Penetration depth, material volume loss, and crater diameter were measured and analyzed. The test results show that the mixture with a combination of 3% 6 mm and 3% of 13 mm length of steel fibers exhibited the best resistance to projectile impact and only the slabs with 15 mm thickness had perforation. Empirical models that predict the depth of penetration were compared with the experimental results. This material can be used as an overlay to buildings or to construct small precast structures.


2008 ◽  
Vol 64 (3) ◽  
pp. 435-448
Author(s):  
Tetsuo KAWAGUCHI ◽  
Makoto KATAGIRI ◽  
Kazuyoshi SHIRAI ◽  
Junichiro NIWA

Sign in / Sign up

Export Citation Format

Share Document