Use of Hemp Fibres in 3D Printed Concrete

The use of fibres as reinforcement of 3D printed concrete is widely known and applicable in many situations. However, most of the applied fibres are not produced from renewable resources. Natural fibres are commonly considered as an ecological alternative for these fibres. In order to contribute to improvement of the sustainability of 3D printed concrete, natural fibres such as hemp can replace these synthetic fibres. The objective of this study is therefore to study the possibilities of adding hemp fibres for 3D printing purposes. Due to the comparable properties of hemp and synthetic fibres, natural fibres tend to be suitable for printing purposes. Mixes are made at laboratory scale using batches of 1 – 3 kg. The study examines the effect of adding hemp fibres for the mechanical and fresh state properties of hemp-based concrete. Mechanical properties from bending tests and direct tensile tests show comparable properties of mortars containing hemp fibres and mortars containing synthetic fibres. The fresh state behaviour of the designed concrete mix showed promising and comparable results for a mix based on 0.5wt% of hemp fibres. One of the major issues regarding the use of natural fibres is the irregularity and high water uptake of the fibres. Due to its high hydrophilicity natural hemp fibres take up much water and can therefore degrade. For this study the effect of water uptake did not have much influence on the mixing and printing purposes. By printing a wall element on laboratory scale the use of hemp fibre-reinforced 3D concrete is validated.

Failure Mechanisms of Structural Bamboo Using Microstructural Analyses

Bamboo is deemed an emerging constructional material with promising application projections due to the reliable natural properties and advantageous structural characteristics. However, there is a lack of systematic studies on the mechanical characteristics of the bamboo species from a microstructural scale. Hence, this paper investigated the primary mechanical properties of the bamboo specimens (Dendrocalamus asper) with further microstructural analysis on the bamboo failure. The direct tensile strength of bamboo specimens was about 226.45 MPa, while the final splitting tensile modulus was found to be 2.88 MPa. Microstructural characterisation of the failed tensile specimens indicates that fibre debonding is the main failure mechanism under tensile conditions. On the other hand, splitting and end bearing failure were found on compression test specimens. In addition, nanoindentation tests were carried out on different cell structures to articulate the hardness and Young’s modulus. The elastic modulus of the fibre cell walls is three times that of the parenchyma cell walls, yet the hardness values are comparable. This confirms that the specimen failure of previous macromechanical testing is due to crack propagation along the parenchyma cells, instead of the cell walls. Based on the experimental studies discussed in this paper, the conclusion can convey a positive message regarding the ability of bamboo as a primary sustainable substitute for conventional construction materials.

Effect of fiber dosage on water permeability using a newly designed apparatus and crack monitoring of steel fiber–reinforced concrete under direct tensile loading

Cracks in concrete structures have always been the main reason to allow the aggressive and harmful agents to infringe the concrete resulting in its deterioration and decreasing lifespan. In the present study, the water permeability of the cracked concrete has been investigated. The consequences of cracking on the durability and endurance of concrete were also studied. A state-of-the-art permeability setup was designed to measure the water flow in normal and fiber-reinforced concrete under direct tensile loading. The setup was convenient for determining the average stress applied to the concrete specimens and simultaneously the maximum crack opening. Furthermore, the effect of fiber content on the cracking geometry (tortuosity and roughness) was evaluated by incorporating the coordinate data of the cracked surface using a 3D sensor-based laser scanning data acquisition system. To understand the effect of fiber content on the cracking geometry (tortuosity and roughness), the acquired data were then analyzed. Test results show that the designed setup is suitable to measure the water permeability under direct tensile loading. Water permeability decreased upon increasing the steel fiber dosage. Besides, the results show that tortuosity decreased while surface roughness increased with the fiber dosage increment. Promising preliminary results indicated that there is an inverse relationship between surface roughness and water permeability. The crack sensing setup successfully monitored the crack.

Feasibility of Using the Hollow Glass Microsphere to Develop Lightweight CAC-GGBFS-Blended Strain-Hardening Cementitious Composites

Strain hardening cementitious composites (SHCCs) with superior tensile strength and ductility have been utilized as an effective repair material. A corrosion-resistant binder, calcium aluminate cement (CAC)–ground granulated blast-furnace slag (GGBFS) blends, has been introduced into SHCC to expand its application in the concrete sewage network rehabilitation. As a repair material, the lightweight property is particularly favorable as it can broaden its functionality. This article presents a study on developing a novel lightweight CAC-GGBFS-blended SHCC using hollow glass microsphere (HGM), namely, HGMLW-SHCCs. The fine silica sand content was substituted with HGM at 25, 50, 75, and 100 vol% in HGMLW-SHCC. We examined flowability, density, uniaxial compressive behavior, direct tensile behavior, and pseudo strain-hardening indices. Microstructure analysis was also conducted to understand the meso-scale behavior of this new lightweight composite. The newly developed HGMLW-SHCC had a 28-day density of only 1756 kg/m3. Compressive and tensile strengths were determined in the range of 62.80–49.39 MPa and 5.81–4.19 MPa, respectively. All mixtures exhibited significant strain-hardening behavior. Even though the increased HGM content negatively affected the tensile strength of HGMLW-SHCC, it had a positive effect on its ductility. In addition, HGM can reduce crack width and tensile stress fluctuations significantly. The results showed that HGM was a promising material for producing strong and lightweight corrosion-resistant SHCCs to be used as a retrofitting material in the wastewater industry.

Calculation Derivation and Test Verification of Indirect Tensile Strength of Asphalt Pavement Interlayers at Low Temperatures

When the direct tensile test is adopted to determine the interlayer tensile strength of the asphalt pavements, specimen separation or internal cracking often occurs at the bonding area of the loading head, rather than at the interlaminar bonding interface. In view of the tedious and discrete data of the direct tensile test, this paper attempts to introduce an indirect tensile test to determine the interlayer bond strength of asphalt pavement to solve this problem. However, the indirect tensile test method of a binder lacks the corresponding mechanical theory. This paper deduces the calculation formula of the indirect tensile strength of a binder based on elastic theory. A mechanical model of the test was established with the finite element method. In accordance with the two-dimensional elastic theory and the Flamant solution, an analytical solution of tensile stress in the indirect tensile test is proposed through the stress superposition. On this basis, the calculation formula for the indirect tensile strength of the interlaminar bonding is derived according to Tresca’s law. A low-temperature indirect tensile test was designed and conducted to verify the correctness of the formula. By comparing the results of the indirect tensile test and direct tensile test, it is found that the interlaminar strength of the mixture measured by them is similar, and the dispersion of indirect tensile test results is small. The results show that the indirect tensile test can replace the direct tensile test to evaluate the interlaminar tensile strength.

Experimental and Numerical Investigation on the Size Effect of Ultrahigh-Performance Fibre-Reinforced Concrete (UHFRC)

In the last few years, there has been increasing interest in the use of Ultrahigh-Performance Fibre-Reinforced Concrete (UHPFRC) layers or jackets, which have been proved to be quite effective in strengthening applications. However, to facilitate the extensive use of UHPFRC in strengthening applications, reliable numerical models need to be developed. In the case of UHPFRC, it is common practice to perform either direct tensile or flexural tests to determine the UHPFRC tensile stress–strain models. However, the geometry of the specimens used for the material characterization is, in most cases, significantly different to the geometry of the layers used in strengthening applications which are normally of quite small thickness. Therefore, and since the material properties of UHPFRC are highly dependent on the dimensions of the examined specimens, the so called “size effect” needs to be considered for the development of an improved modelling approach. In this study, direct tensile tests have been used and a constitutive model for the tensile behaviour of UHPFRC is proposed, taking into consideration the size of the finite elements. The efficiency and reliability of the proposed approach has been validated using experimental data on prisms with different geometries, tested in flexure and in direct tension.

Interfacial Bond Properties between Normal Strength Concrete and Epoxy Resin Concrete

It is necessary to pay attention to the bonding strength of the interface between precast normal strength concrete (NSC) and cast-in-place epoxy resin concrete (EMR) when using EMR as a repair or filling material or an overlay in bridges’ rehabilitation. However, the performances of epoxy concrete are different due to differential mix ratios; thus, the bonding properties between various epoxy resin concrete and cement concrete are not completely the same. This article investigated the interfacial bond properties between NSC and ERC by direct tensile, push-out, and slant shear test with specimens of special size and structure and observed the interfacial bond strength and corresponding failure modes. The minimum bond strength under direct tension was 0.72 MPa, while the minimum bond strength was 1.71 MPa and 3.19 MPa for the push-out test and slant shear test, respectively. Results indicated that the slant shear test specimens with an inclination angle of 45° are not suitable for the slant shear test due to higher compressive stress. Furthermore, the cohesion and friction coefficient of interface bond strength were calculated inversely in accordance with the results obtained from the corresponding direct tensile and slant shear tests. The minimum cohesion value was 1.71 MPa, and the minimum friction coefficient value was 0.46.