Study of hydrogen impact on lean limit and burning characteristics of a kerosene surrogate

Energy ◽  
2021 ◽  
pp. 120925
Author(s):  
M. Zuhaib Akram
Keyword(s):  
Lean Limit

Identification of the extinction mechanism of lean limit hydrogen flames based on Lewis number effect

2021 ◽  
Vol 174 ◽  
pp. 121288
Author(s):  
Joongoo Jeon ◽  
Doyoung Shin ◽  
Wonjun Choi ◽  
Sung Joong Kim
Keyword(s):  
Lewis Number ◽  
Lean Limit

Ignition System Designed to Extend the Plug Life, and the Lean Limit in a Natural Gas Engine

2003 ◽  
Author(s):  
A. K. Chan ◽  
S. H. Waters
Keyword(s):  
Natural Gas ◽  
Engine Performance ◽  
Ignition System ◽  
Gas Engine ◽  
Natural Gas Engine ◽  
Dc System ◽  
Spark Plug ◽  
Long Duration ◽  
Discharge Duration ◽  
Lean Limit

An ignition system that is based on the alternating (AC) rather than the traditional direct (DC) current in the spark plug discharge has been developed at the Caterpillar Technical Center. This system can generate a long duration discharge with controllable power. It is believed that such an ignition system can provide both a leaner operating limit and a longer spark plug life than a traditional DC system due to the long discharge duration and the low discharge power. The AC ignition system has successfully been tested on a Caterpillar single cylinder G3500 natural gas engine to determine the effects on the engine performance, combustion characteristics and emissions. The test results indicate that while the AC ignition system has only a small impact on engine performance (with respect to a traditional DC system), it does extend the lean limit with lower NOx emissions. Evidences also show the potential of reduce spark plug electrode erosions from the low breakdown and sustaining discharge powers from the AC ignition system. This paper summarizes the prototype design and engine demonstration results of the AC ignition system.

Effect of injection and ignition timing on a hydrogen-lean stratified charge combustion engine

2021 ◽  
pp. 146808742110346
Author(s):  
Sanguk Lee ◽  
Gyeonggon Kim ◽  
Choongsik Bae
Keyword(s):  
Internal Combustion Engines ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Combustion Stability ◽  
Transport Sector ◽  
Injection Timing ◽  
Ignition Timing ◽  
Particulate Emission ◽  
Stratified Charge ◽  
Lean Limit

Hydrogen can be used as a fuel for internal combustion engines to realize a carbon-neutral transport society. By extending the lean limit of spark ignition engines, their efficiency, and emission characteristics can be improved. In this study, stratified charge combustion (SCC) using monofueled hydrogen direct injection was used to extend the lean limit of a spark ignition engine. The injection and ignition timing were varied to examine their effect on the SCC characteristics. An engine experiment was performed in a spray-guided single-cylinder research engine, and the nitrogen oxide and particulate emissions were measured. Depending on the injection timing, two different types of combustion were characterized: mild and hard combustion. The advancement and retardation of the ignition timing resulted in a high and low combustion stability, respectively. The lubricant-based particulate emission was attributed to the in-cylinder temperature and area of the flame surface. Therefore, the results of the study suggest that the optimization of the hydrogen SCC based on the injection and ignition timing could contribute to a clean and efficient transport sector.

Experimental study of combustion strategy for jet ignition on a natural gas engine

2020 ◽  
pp. 146808742097775
Author(s):  
Ziqing Zhao ◽  
Zhi Wang ◽  
Yunliang Qi ◽  
Kaiyuan Cai ◽  
Fubai Li
Keyword(s):  
Experimental Study ◽  
Natural Gas ◽  
Efficient Points ◽  
Lean Burn ◽  
Gas Engine ◽  
Absolute Value ◽  
Natural Gas Engines ◽  
Natural Gas Engine ◽  
Excess Air ◽  
Lean Limit

To explore a suitable combustion strategy for natural gas engines using jet ignition, lean burn with air dilution, stoichiometric burn with EGR dilution and lean burn with EGR dilution were investigated in a single-cylinder natural gas engine, and the performances of two kinds of jet ignition technology, passive jet ignition (PJI) and active jet ignition (AJI), were compared. In the study of lean burn with air dilution strategy, the results showed that AJI could extend the lean limit of excess air ratio (λ) to 2.1, which was significantly higher than PJI’s 1.6. In addition, the highest indicated thermal efficiency (ITE) of AJI was shown 2% (in absolute value) more than that of PJI. Although a decrease of NOx emission was observed with increasing λ in the air dilution strategy, THC and CO emissions increased. Stoichiometric burn with EGR was proved to be less effective, which can only be applied in a limited operation range and had less flexibility. However, in contrast to the strategy of stoichiometric burn with EGR, the strategy of lean burn with EGR showed a much better applicability, and the highest ITE could achieve 45%, which was even higher than that of lean burn with air dilution. Compared with the most efficient points of lean burn with pure air dilution, the lean burn with EGR dilution could reduce 78% THC under IMEP = 1.2 MPa and 12% CO under IMEP = 0.4 MPa. From an overall view of the combustion and emission performances under both low and high loads, the optimum λ would be from 1.4 to 1.6 for the strategy of lean burn with EGR dilution.

Fuel Stratification Using Twin-Tumble Intake Flows to Extend Lean Limit in Super-Lean Gasoline Combustion

2018 ◽  
Author(s):  
Yasuo Moriyoshi ◽  
Tatsuya Kuboyama ◽  
Makoto Kaneko ◽  
Toshio Yamada ◽  
Hironao Sato
Keyword(s):  
Fuel Stratification ◽  
Lean Limit ◽  
Lean Gasoline

Effects of H2/CO addition on knock tendency and lean limit in a natural gas SI engine

Fuel ◽  
2018 ◽  
Vol 233 ◽  
pp. 582-591 ◽  
Author(s):  
Changpeng Liu ◽  
Fubai Li ◽  
Heping Song ◽  
Zhi Wang
Keyword(s):  
Natural Gas ◽  
Si Engine ◽  
Lean Limit ◽  
Co Addition

Lean Blowout Phenomena and Prior Detection of Lean Blowout in a Premixed Model Annular Combustor

2019 ◽  
Author(s):  
Arijit Bhattacharya ◽  
Bikash Gupta ◽  
Satyajit Hansda ◽  
Zohadul Haque ◽  
Ashish Kumar ◽  
...  
Keyword(s):  
Bluff Body ◽  
Nox Reduction ◽  
Marked Change ◽  
Nox Emission ◽  
Thermoacoustic Instability ◽  
Lean Blowout ◽  
Lean Combustion ◽  
Annular Combustor ◽  
Lean Limit ◽  
Lift Off

Abstract Strict emission norms in the last few decades have paved the path for adaptation of new low NoX emission alternatives to power generation and aircraft propulsion. Lean combustion is a very promising and practicable technology for reducing NOX reduction and also have very high fuel efficiency. However, lean combustion technology suffers from inherent combustion instabilities that are manifested under different conditions, most importantly, thermoacoustic instability and lean blowout. Lean blowout occurs when a gas turbine combustor operating close to lean limit, for lowest NoX emission, faces abrupt changes in fuel homogeneity, quality or flow rate. While many work have been done in thermo-acoustic instability and flame propagation in annular combustors, studies in lean blowout in annular combustors are very limited. The lean limit of combustors are not fixed and is dependent on fuel characteristics and operating condition including environmental effects. So accurate online prediction of lean limit is very important to keep the combustors operating safely near lean limit. Recent works have demonstrated that single burner combustors leave out a significant amounts of physics including interaction of flames from different burners prior to blowout. In this work, a stepped down swirl and bluff body stabilized annular combustor in CB configuration (having chamber and burner), is used as experimental test rig having 4 number of identical burners. Video and heat release data are taken at different conditions as lean blowout is approached. Frequent attachment and reattachment of the flames prior to lift off was seen. As lean blowout is approached, inherent subtle differences in the different burners get amplified when flame becomes sufficiently weak and flame symmetry is broken. As air fuel mixture is made gradually leaner, one by one the flames from different burners elongates although remains partially attached to burner. Further lowering the equivalence ratio results in lift off and merging of the flame fronts of different burners. Three pixel averaged color ratios are extracted from still camera RGB images as flame stability indicators which are, red by blue, red by green and blue by green. The parameters show marked change at the point of lift off as well as at the lean blowout point.

Sign in / Sign up

Export Citation Format

Share Document