scholarly journals Finite element modelling approach for precast reinforced concrete beam-to-column connections under cyclic loading

2018 ◽  
Vol 174 ◽  
pp. 49-66 ◽  
Author(s):  
De-Cheng Feng ◽  
Gang Wu ◽  
Yong Lu
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Cyclic Loading ◽  
Finite Element Modelling ◽  
Concrete Beam ◽  
Reinforced Concrete Beam ◽  
Element Modelling ◽  
Modelling Approach

Simulation Behavior of Flexure in Reinforced Concrete Beam with Opening Reinforced with Glass Fiber Reinforced Polymer (GFRP)

2016 ◽  
Vol 857 ◽  
pp. 421-425
Author(s):  
Saif M. Thabet ◽  
S.A. Osman
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Glass Fiber ◽  
Concrete Beam ◽  
Reinforced Concrete Beam ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Glass Fiber Reinforced Polymer ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced

This paper presents an investigation into the flexural behaviour of reinforced concrete beam with opening reinforced with two different materials i.e., steel and Glass Fiber Reinforced Polymer (GFRP). Comparison study between the two different materials were carried out and presented in this study through non-linear Finite Element Method (FEM) using the commercial ABAQUS 6.10 software package. The performance of the opening beam reinforced with GFRP is influenced by several key parameters. Simulation analyses were carried out to determine the behavior of beam with opening subjected to monotonic loading. The main parameters considered in this study are size of opening and reinforcement diameter. The results show that GFRP give 23%-29% more ductility than steel reinforcement. The result also shows when the size of opening change from 200mm to 150mm or from 150mm to 100mm the ultimate load capacity increase by 15%. In general, good agreement between the Finite Element (FE) simulation and the available experimental result has been obtained.

Experimental studies on performance of reinforced concrete beam strengthened with CFRP under cyclic loading using FBG array

Measurement ◽  
2013 ◽  
Vol 46 (10) ◽  
pp. 3855-3862 ◽  
Author(s):  
K. Kesavan ◽  
K. Ravisankar ◽  
R. Senthil ◽  
A.K. Farvaze Ahmed
Keyword(s):  
Reinforced Concrete ◽  
Cyclic Loading ◽  
Concrete Beam ◽  
Experimental Studies ◽  
Reinforced Concrete Beam

scholarly journals Numerical Derivation of Iso-Damaged Curve for a Reinforced Concrete Beam Subjected to Blast Loading

2018 ◽  
Vol 149 ◽  
pp. 02016 ◽  
Author(s):  
Yehya Temsah ◽  
Ali Jahami ◽  
Jamal Khatib ◽  
M Sonebi
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Shock Waves ◽  
Concrete Beam ◽  
Blast Loading ◽  
Reinforced Concrete Beam ◽  
Structural Elements ◽  
Finite Element Program ◽  
Element Program ◽  
Structural Engineers

Many engineering facilities are severely damaged by blast loading. Therefore, many manufacturers of sensitive, breakable, and deformed structures (such as facades of glass buildings) carry out studies and set standards for these installations to withstand shock waves caused by explosions. Structural engineers also use these standards in their designs for various structural elements by following the ISO Damage Carve, which links pressure and Impulse. As all the points below this curve means that the structure is safe and will not exceed the degree of damage based on the various assumptions made. This research aims to derive the Iso-Damage curve of a reinforced concrete beam exposed to blast wave. An advanced volumetric finite element program (ABAQUS) will be used to perform the derivation.

Uniform loading on the reinforced concrete beam produced by the specific cylinder-shaped rubber bags fully filled with air or water

2020 ◽  
Vol 23 (9) ◽  
pp. 1934-1947
Author(s):  
Dapeng Chen ◽  
Li Chen ◽  
Qin Fang ◽  
Yuzhou Zheng ◽  
Teng Pan
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Element Model ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Uniform Loading ◽  
Air Bag

The bending behavior of reinforced concrete beams under uniform pressure is critical for the research of the blast-resistance performance of structural components under explosive loads. In this study, a bending test of five reinforced concrete beams with the dimensions of 200 mm (width) × 200 mm (depth) × 2500 mm (length) under uniform load produced by a specific cylinder-shaped rubber bag filled with air or water was conducted to investigate their flexural performances. An air bag load was applied to three of the reinforced concrete beams, a water bag load was applied to one reinforced concrete beam, and the remainder beam was subjected to the 4-point bending load. The experimental results highlighted that the air bag and water bag loading methods can be used to effectively apply uniform loads to reinforced concrete beams. Moreover, the stiffness of the air bag was improved by 123% in accordance with the initial pressure increases from 0.15 to 0.45 MPa. In addition, a finite element model of the test loading system was established using ABAQUS/Standard software. Moreover, the critical factors of the air bag loading method were analyzed using the numerical model. The calculated results were found to be in good agreement with the test data. The established finite element model can therefore be used to accurately simulate the action performances of the uniform loading technique using rubber bags filled with air or water.

Sign in / Sign up

Export Citation Format

Share Document