scholarly journals Numerical Derivation of Iso-Damaged Curve for a Reinforced Concrete Beam Subjected to Blast Loading

2018 ◽  
Vol 149 ◽  
pp. 02016 ◽  
Author(s):  
Yehya Temsah ◽  
Ali Jahami ◽  
Jamal Khatib ◽  
M Sonebi
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Shock Waves ◽  
Concrete Beam ◽  
Blast Loading ◽  
Reinforced Concrete Beam ◽  
Structural Elements ◽  
Finite Element Program ◽  
Element Program ◽  
Structural Engineers

Many engineering facilities are severely damaged by blast loading. Therefore, many manufacturers of sensitive, breakable, and deformed structures (such as facades of glass buildings) carry out studies and set standards for these installations to withstand shock waves caused by explosions. Structural engineers also use these standards in their designs for various structural elements by following the ISO Damage Carve, which links pressure and Impulse. As all the points below this curve means that the structure is safe and will not exceed the degree of damage based on the various assumptions made. This research aims to derive the Iso-Damage curve of a reinforced concrete beam exposed to blast wave. An advanced volumetric finite element program (ABAQUS) will be used to perform the derivation.

scholarly journals TECHNOLOGY OF COMPUTATION OF REINFORCED CONCRETE STRUCTURES/GELŽBETONINŲ KONSTRUKCIJŲ ARMATŪROS AUTOMATIZUOTO SKAIČIAVIMO TECHNOLOGIJA

2001 ◽  
Vol 7 (6) ◽  
pp. 419-424
Author(s):  
Arvydas Jurkša
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Concrete Beam ◽  
New Technology ◽  
Concrete Structures ◽  
Reinforced Concrete Structures ◽  
Finite Element Program ◽  
Code Of Practice ◽  
Element Program

The author has created a new technology for concrete beam, column, slab, wall and shell reinforcement computation according to the finite element program COSMOS/M analysis results and code of practice valid in Lithuania. A brief description of the technology is included in the article. Computer programmes COSARM and COSMAX were designed for slab, wall and shell reinforcement computation. Results can be visualized graphically. New computer programmes BEAM, COSBEAM, COLUMN, COSREC and COSCIR were created for beam and column reinforcement computation. The new technology extremely enlarged the possibilities of the powerful finite element program COSMOS/M and enabled to compute very complicated reinforced concrete structures.

Simulation Behavior of Flexure in Reinforced Concrete Beam with Opening Reinforced with Glass Fiber Reinforced Polymer (GFRP)

2016 ◽  
Vol 857 ◽  
pp. 421-425
Author(s):  
Saif M. Thabet ◽  
S.A. Osman
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Glass Fiber ◽  
Concrete Beam ◽  
Reinforced Concrete Beam ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Glass Fiber Reinforced Polymer ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced

This paper presents an investigation into the flexural behaviour of reinforced concrete beam with opening reinforced with two different materials i.e., steel and Glass Fiber Reinforced Polymer (GFRP). Comparison study between the two different materials were carried out and presented in this study through non-linear Finite Element Method (FEM) using the commercial ABAQUS 6.10 software package. The performance of the opening beam reinforced with GFRP is influenced by several key parameters. Simulation analyses were carried out to determine the behavior of beam with opening subjected to monotonic loading. The main parameters considered in this study are size of opening and reinforcement diameter. The results show that GFRP give 23%-29% more ductility than steel reinforcement. The result also shows when the size of opening change from 200mm to 150mm or from 150mm to 100mm the ultimate load capacity increase by 15%. In general, good agreement between the Finite Element (FE) simulation and the available experimental result has been obtained.

Uniform loading on the reinforced concrete beam produced by the specific cylinder-shaped rubber bags fully filled with air or water

2020 ◽  
Vol 23 (9) ◽  
pp. 1934-1947
Author(s):  
Dapeng Chen ◽  
Li Chen ◽  
Qin Fang ◽  
Yuzhou Zheng ◽  
Teng Pan
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Element Model ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Uniform Loading ◽  
Air Bag

The bending behavior of reinforced concrete beams under uniform pressure is critical for the research of the blast-resistance performance of structural components under explosive loads. In this study, a bending test of five reinforced concrete beams with the dimensions of 200 mm (width) × 200 mm (depth) × 2500 mm (length) under uniform load produced by a specific cylinder-shaped rubber bag filled with air or water was conducted to investigate their flexural performances. An air bag load was applied to three of the reinforced concrete beams, a water bag load was applied to one reinforced concrete beam, and the remainder beam was subjected to the 4-point bending load. The experimental results highlighted that the air bag and water bag loading methods can be used to effectively apply uniform loads to reinforced concrete beams. Moreover, the stiffness of the air bag was improved by 123% in accordance with the initial pressure increases from 0.15 to 0.45 MPa. In addition, a finite element model of the test loading system was established using ABAQUS/Standard software. Moreover, the critical factors of the air bag loading method were analyzed using the numerical model. The calculated results were found to be in good agreement with the test data. The established finite element model can therefore be used to accurately simulate the action performances of the uniform loading technique using rubber bags filled with air or water.

scholarly journals Numerical Simulation on Reinforced Concrete Beam with Different Cover Size under Two Point Bending Load

2021 ◽  
Vol 7 (05) ◽  
pp. 39-43
Author(s):  
R Padma Rani & R Harshani
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Structural Analysis ◽  
Concrete Beam ◽  
Failure Modes ◽  
Equivalent Stress ◽  
Reinforced Concrete Beam ◽  
Simulation Software ◽  
Beam Specimen ◽  
Bending Load

Structural analysis is used to assess the behavior of engineering structures under the application of loads. Usually, structural analysis methods include analytical,experimental and numerical methods is used in thisproject, however, only Analytical method is used and the values are taken from literature reference, to get familiar with Finite Element Analysis (FEA) using ANSYS, this is done to acquire practical knowledge about of the effect of the cover. The aim is to identify different failure modes under a range of loading conditions by changing the cover size to get the data of various parameters such as deflection, stress etc. Study of cover helps to observe the stability, reliability and the overall strength of the structural beam. This project attempts made to study the effect of cover on the behavior of reinforced concrete beam. Forthis analytical study, the Reinforced concrete beam specimen of 2000x100x200mm was considered.ANSYS software is a suite of engineering simulation software, based on finite element method, which can solve problems ranging from linear analysis to nonlinear analysis. The Doubly reinforced beams weremodeled by using geometry. In this model,various covers are provided. The beam specimensused in this study were tested under two-point static loading condition until failure of the specimen. From theobtained resultconcluded that the total deformation and directional deformation values are low in 25mm cover compared to other cases but the equivalent stress value is low in 35mm cover size compared to 25mm cover size.

Analytical Study on the Flexural Behavior of Reinforced Concrete Beam with Mineral Admixture under Calcium Leaching Degradation

2018 ◽  
Vol 940 ◽  
pp. 123-127
Author(s):  
Il Sun Kim ◽  
Yoon Suk Choi ◽  
Chan Kyu Lee ◽  
Eun Ik Yang
Keyword(s):  
Finite Element ◽  
Load Capacity ◽  
Pure Water ◽  
Reinforced Concrete Beam ◽  
Mineral Admixture ◽  
Flexural Behavior ◽  
Mineral Admixtures ◽  
Finite Element Program ◽  
Calcium Leaching ◽  
Element Program

Calcium leaching degradation could be happened in reinforcement concrete member due to the contact with pure water in underground condition. Thus, it is needed to evaluate the resistance of calcium leaching for concrete mixed with mineral admixtures. So, in this paper, to evaluate the flexural behavior in RC member with mineral admixture under calcium leaching degradation, we investigated the effect of calcium leaching using the non-linear finite-element program. From the results, the load capacity and flexible rigidity of a degraded RC member decrease when the degradation level increases with leaching period. And, regardless of the type of mineral admixtures, finite-element-method analysis effectively showed the characteristics of calcium leaching damaged RC beam.

Spalling in Continuously Reinforced Concrete Pavement in Texas

2020 ◽  
Vol 2674 (11) ◽  
pp. 731-740
Author(s):  
Pangil Choi ◽  
Lochana Poudyal ◽  
Fouzieh Rouzmehr ◽  
Moon Won
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Coefficient Of Thermal Expansion ◽  
Field Testing ◽  
Concrete Pavement ◽  
Materials Testing ◽  
Finite Element Program ◽  
Texas Department ◽  
Conducting Materials ◽  
Element Program

The performance of continuously reinforced concrete pavement (CRCP) in Texas has been quite satisfactory, primarily thanks to the continuous improvements in design and construction. However, severe spalling has been a major problem, and the Texas Department of Transportation (TxDOT) has sponsored several research projects since 1985 to identify solutions for this serious problem. Even though the research efforts were successful in identifying spalling mechanisms, developing a policy that TxDOT could easily implement has been a challenge. To develop a more practical solution to this problem, TxDOT initiated a research study, and the research efforts consisting of identifying CRCP projects with severe and no spalling, obtaining and conducting materials testing on concrete cores from those projects, analyzing the testing data, and performing theoretical analyses to validate the testing results. Among the material properties evaluated, the coefficient of thermal expansion (CTE) of concrete proved to have the best correlation with spalling. Detailed analyses of mechanistic behavior of concrete conducted with an object-oriented finite element program (OOF2) and commercial finite element program verified the reasonableness of the field-testing results. All concrete cores from CRCP with severe spalling had a CTE larger than 5.5 microstrains/°F, whereas no spalling was observed in concrete with a CTE less than that value. Based on this finding, TxDOT now requires the use of coarse aggregate that will produce concrete with a CTE of less than 5.5 microstrains/°F for CRCP construction. It is expected that this implementation will reduce the spalling in CRCP substantially.

scholarly journals A NONLINEAR FINITE ELEMENT ANALYSIS OF PRECAST INDUSTRIALISED BUILDING SYSTEM BEAM UNDER FLEXURAL TEST

2019 ◽  
Vol 81 (3) ◽  
Author(s):  
Chun-Chieh Yip ◽  
Jing-Ying Wong ◽  
Ka-Wai Hor
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Reinforced Concrete ◽  
Concrete Beam ◽  
Failure Modes ◽  
Reinforced Concrete Beam ◽  
Shear Cracks ◽  
Flexural Test ◽  
Element Analysis ◽  
Failure Behaviour

Software simulation enables design engineers to have a better picture of possible structural failure behaviour and determine the accuracy of a design before the actual structural component is fabricated. Finite element analysis is used to simulate the behaviour of the reinforced concrete beam under the flexural test. During the flexural test, results are recorded for both simulation and experimental tests. By comparing the results, beam displacement, crack patterns, and failure modes can be studied with better accuracy. The accuracy percentage for yield load and ultimate load between the two tests results were 94.12 % and 95.79 %, respectively, whereas the accuracy percentage for elastic gradient before the yielding stage was 81.08 %. The behaviour between simulation and laboratory models described is based on crack pattern and failure mode. The progression of von Mises (VM) stresses highlighted the critical areas of the reinforced concrete beam and correlation between the experimental specimen, in terms of flexural cracks, shear cracks, yielding of tension reinforcement, and the crushing of concrete due to compressive stress. This paper concludes that simulation can achieve a significant accuracy in terms of loads and failure behaviour compared to the experimental model.

Sign in / Sign up

Export Citation Format

Share Document