Effect of hydrogen on fracture behavior of Ti–6Al–4V alloy by in-situ tensile test

2010 ◽  
Vol 35 (4) ◽  
pp. 1829-1838 ◽  
Author(s):  
B.G. Yuan ◽  
H.P. Yu ◽  
C.F. Li ◽  
D.L. Sun
Keyword(s):  
Tensile Test ◽  
Fracture Behavior

In-situ X-ray tomography investigation of pore damage effects during a tensile test of a Ni-based single crystal superalloy

2021 ◽  
pp. 111180
Author(s):  
Keli Liu ◽  
Junsheng Wang ◽  
Bing Wang ◽  
Pengcheng Mao ◽  
Yanhong Yang ◽  
...  
Keyword(s):  
Tensile Test ◽  
Single Crystal ◽  
Single Crystal Superalloy ◽  
X Ray

scholarly journals Morphology and Mechanical Properties of Fossil Diatom Frustules from Genera of Ellerbeckia and Melosira

Nanomaterials ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 1615
Author(s):  
Qiong Li ◽  
Jürgen Gluch ◽  
Zhongquan Liao ◽  
Juliane Posseckardt ◽  
André Clausner ◽  
...  
Keyword(s):  
Fracture Behavior ◽  
Three Dimensional ◽  
Mechanical Tests ◽  
Fracture Force ◽  
Thickness Change ◽  
X Ray ◽  
Transmission Electron ◽  
Percentage Concentration ◽  
Morphology Characterization

Fossil frustules of Ellerbeckia and Melosira were studied using laboratory-based nano X-ray tomography (nano-XCT), transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS). Three-dimensional (3D) morphology characterization using nondestructive nano-XCT reveals the continuous connection of fultoportulae, tube processes and protrusions. The study confirms that Ellerbeckia is different from Melosira. Both genera reveal heavily silicified frustules with valve faces linking together and forming cylindrical chains. For this cylindrical architecture of both genera, valve face thickness, mantle wall thickness and copulae thickness change with the cylindrical diameter. Furthermore, EDS reveals that these fossil frustules contain Si and O only, with no other elements in the percentage concentration range. Nanopores with a diameter of approximately 15 nm were detected inside the biosilica of both genera using TEM. In situ micromechanical experiments with uniaxial loading were carried out within the nano-XCT on these fossil frustules to determine the maximal loading force under compression and to describe the fracture behavior. The fracture force of both genera is correlated to the dimension of the fossil frustules. The results from in situ mechanical tests show that the crack initiation starts either at very thin features or at linking structures of the frustules.

scholarly journals Crack Propagation Behavior of a Ni-Based Single-Crystal Superalloy during In Situ SEM Tensile Test at 1000 °C

Crystals ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1047
Author(s):  
Wenxiang Jiang ◽  
Xiaoyi Ren ◽  
Jinghao Zhao ◽  
Jianli Zhou ◽  
Jinyao Ma ◽  
...  
Keyword(s):  
Crack Propagation ◽  
Tensile Test ◽  
Single Crystal ◽  
Crack Propagation Rate ◽  
Propagation Rate ◽  
Single Crystal Superalloy ◽  
Propagation Path ◽  
Propagation Behavior ◽  
Crack Propagation Behavior

An in situ scanning electron microscope (SEM) tensile test for Ni-based single-crystal superalloy was carried out at 1000 °C. The stress displacement was obtained, and the yield strength and tensile strength of the superalloy were 699 MPa and 826 MPa, respectively. The crack propagation process, consisting of Model I crack and crystallographic shearing crack, was determined. More interestingly, the crack propagation path and rate affected by eutectics was directly observed and counted. Results show that the coalescence of the primary crack and second microcrack at the interface of a γ/γ′ matrix and eutectics would make the crack propagation rate increase from 0.3 μm/s to 0.4 μm/s. On the other hand, crack deflection decreased the rate to 0.05 μm/s. Moreover, movement of dislocations in front of the crack was also analyzed to explain the different crack propagation behavior in the superalloy.

Tensile Properties and Fracture Behavior of SiCp/AC4CH Composite at Loading Velocities of up to 10m/s

2004 ◽  
Vol 449-452 ◽  
pp. 305-308
Author(s):  
Lei Wang ◽  
Toshiro Kobayashi ◽  
Chun Ming Liu
Keyword(s):  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Tensile Test ◽  
Strain Rate ◽  
Fracture Behavior ◽  
Tensile Deformation ◽  
Optical Microscope ◽  
Fracture Elongation ◽  
Before And After

Tensile test at loading velocities up to 10 m·s-1(strain rate up to 3.2x102s-1) was carried out forr SiCp/AC4CH composite and AC4CH alloy. The microstructure of the composite before and after tensile deformation was carefully examined with both optical microscope and SEM. The experimental results demonstrated that the ultimate tensile strength (UTS) and yield strength (YS) increase with increasing loading velocity up to 10 m·s-1. Comparing with AC4CH alloy, the fracture elongation of the composite is sensitivity with the increasing strain rate. The YS of both the composite and AC4CH alloy shows more sensitive than that of the UTS with the increasing strain rate, especially in the range of strain rate higher than 102s-1.

Mechanical Properties of Flat Braided Composites With a Circular Hole

1999 ◽  
Author(s):  
Takeru Ohki ◽  
Shinya Ikegaki ◽  
Ken Kurasiki ◽  
Hiroyuki Hamada ◽  
Masaharu Iwamoto
Keyword(s):  
Mechanical Properties ◽  
Tensile Test ◽  
Circular Hole ◽  
Fracture Behavior ◽  
Fatigue Property ◽  
Tensile Tests ◽  
Fatigue Tests ◽  
Braided Composites ◽  
Static Tensile ◽  
The One

Abstract In this study, fracture behavior and strength in the flat braided bar with a circular hole were investigated by static and fatigue test. Two type of specimens were prepared. They are a braided flat bar with an integrally-formed braided hole and a braided flat bar with a machined hole. Moreover, we also examined a specimen that had a metal pin inserted at the circular hole. This specimen was subjected to a static tensile test. The results of the tensile tests indicate that the strength of the flat bar with a braided hole was larger than that of the one with the machined hole. Furthermore, from the results of the fatigue tests, the flat bar with the braided hole showed higher fatigue property than that of the one with the machined hole.

Sign in / Sign up

Export Citation Format

Share Document