Conversion of natural gas jet flame burners to hydrogen

2021 ◽  
Author(s):  
Adriana Palacios ◽  
Derek Bradley
Keyword(s):  
Natural Gas ◽  
Gas Jet ◽  
Jet Flame

Attaching Characteristics of the Natural Gas Jet Flame in Air-Coflow at Various Conditions

2015 ◽  
Vol 141 (4) ◽  
pp. 04014042 ◽  
Author(s):  
Ye Yuan ◽  
Guo-Xiu Li ◽  
Zi-Hang Zhou ◽  
Zuo-Yu Sun
Keyword(s):  
Natural Gas ◽  
Gas Jet ◽  
Jet Flame

A Numerical Investigation on Mixing Characteristics of Natural Gas Jets With High-Pressure Injection

2021 ◽  
Author(s):  
Long Liu ◽  
Tianyang Dai ◽  
Qian Xiong ◽  
Yuehua Qian ◽  
Bo Liu
Keyword(s):  
High Pressure ◽  
Natural Gas ◽  
Air Entrainment ◽  
Gas Jet ◽  
Swirl Ratio ◽  
Marine Engine ◽  
Low Speed ◽  
Pressure Injection ◽  
Mixing Characteristics ◽  
High Pressure Injection

Abstract With increasingly stringent emissions limitation of greenhouse gas and atmospheric pollutants for ship, the direct injection of natural gas on the cylinder head with high-pressure injection is an effective method to make a high power output and decrease harmful gas emissions in marine natural gas dual fuel engines. However, the effects on mixing characteristics of high-pressure natural gas underexpanded jet have not been fully understood. Especially, the injection pressure is up to 30 MPa with large injection quantity and critical surrounding gas conditions for the low-speed two-stroke marine engine. Therefore, this research is focused on the flow and mixing process of the natural gas jet with high-pressure injection under the in-cylinder conditions of low-speed two-stroke marine engine. The gas jet penetration, the distribution of velocity and density, the equivalence ratio and air entrainment have been analyzed under different nozzle hole diameters by numerical simulation. The effects of surrounding gas conditions including pressure, temperature and swirl ratio on air entrainment and equivalence ratio distribution were studied in detail. From the numerical simulation, it is found that the mixing characteristics of natural gas jet can be improved under in-cylinder conditions of higher ambient temperature and swirl ratio, which is relevant to the low-speed two-stroke marine engine.

A quasi-one-dimensional model for an outwardly opening poppet-type direct gas injector for internal combustion engines

2019 ◽  
Vol 21 (8) ◽  
pp. 1493-1519
Author(s):  
Abhishek Y Deshmukh ◽  
Carsten Giefer ◽  
Dominik Goeb ◽  
Maziar Khosravi ◽  
David van Bebber ◽  
...  
Keyword(s):  
Natural Gas ◽  
Internal Combustion Engines ◽  
Flow Model ◽  
Direct Injection ◽  
Source Model ◽  
Gas Jet ◽  
Nozzle Flow ◽  
Combustion Engines ◽  
Compressed Natural Gas ◽  
One Dimensional

Direct injection of compressed natural gas in internal combustion engines is a promising technology to achieve high indicated thermal efficiency and, at the same time, reduce harmful exhaust gas emissions using relatively low-cost fuel. However, the design and analysis of direct injection–compressed natural gas systems are challenging due to small injector geometries and high-speed gas flows including shocks and discontinuities. The injector design typically involves either a multi-hole configuration with inwardly opening needle or an outwardly opening poppet-type valve with small geometries, which make accessing the near-nozzle-flow field difficult in experiments. Therefore, predictive simulations can be helpful in the design and development processes. Simulations of the gas injection process are, however, computationally very expensive, as gas passages of the order of micrometers combined with a high Mach number compressible gas flow result in very small simulation time steps of the order of nanoseconds, increasing the overall computational wall time. With substantial differences between in-nozzle and in-cylinder length and velocity scales, simultaneous simulation of both regions becomes computationally expensive. Therefore, in this work, a quasi-one-dimensional nozzle-flow model for an outwardly opening poppet-type injector is developed. The model is validated by comparison with high-fidelity large-eddy simulation results for different nozzle pressure ratios. The quasi-one-dimensional nozzle-flow model is dynamically coupled to a three-dimensional flow solver through source terms in the governing equations, named as dynamically coupled source model. The dynamically coupled source model is then applied to a temporal gas jet evolution case and a cold flow engine case. The results show that the dynamically coupled source model can reasonably predict the gas jet behavior in both cases. All simulations using the new model led to reductions of computational wall time by a factor of 5 or higher.

Industrial-scale processing of granite surfaces by natural gas jet flames

2002 ◽  
Vol 22 (4) ◽  
pp. 393-405 ◽  
Author(s):  
H.H. Liakos ◽  
M.K. Koukou ◽  
M.A. Founti ◽  
N.C. Markatos
Keyword(s):  
Natural Gas ◽  
Gas Jet ◽  
Industrial Scale ◽  
Jet Flames
Sign in / Sign up

Export Citation Format

Share Document