Experimental investigation of damaged square short RC columns with low slenderness retrofitted by CFRP strips under axial load

Structures ◽  
2020 ◽  
Vol 28 ◽  
pp. 170-180 ◽  
Author(s):  
Rahim Ghoroubi ◽  
Ömer Mercimek ◽  
Anıl Özdemir ◽  
Özgür Anil
Keyword(s):  
Experimental Investigation ◽  
Axial Load ◽  
Rc Columns

Experimental Investigation of Stiffened Square CFST Columns under Axial Load

2014 ◽  
Vol 919-921 ◽  
pp. 1794-1800
Author(s):  
Xin Zhi Zheng ◽  
Xin Hua Zheng
Keyword(s):  
Experimental Investigation ◽  
Bearing Capacity ◽  
Cross Sections ◽  
Axial Load ◽  
Local Buckling ◽  
Test Results ◽  
Tubular Columns ◽  
Economical Benefit ◽  
Steel Consumption ◽  
Cfst Columns

Abstract: 7 square steel tubular columns were tested to discuss the ultimate axial bearing capacity, ductility performance and the steel consumption under stiffened by steel belts and binding bars of different cross-sections. Test results indicate that only by increasing fewer amounts of steel usage, stiffened square CFST columns with binding bars can not only improve the overall effects of restraint and alleviate regional local buckling between the binding bars, but also improve the bearing capacity of concrete filled square steel tubular columns. The utility benefits and the economical benefit is considerable, deserving extensive use.

EFFECT OF ASPECT RATIO ON THE BEHAVIOR OF GFRP-RC CIRCULAR COLUMNS UNDER SIMULATED SEISMIC LOADING

2021 ◽  
Vol 8 (1) ◽  
Author(s):  
Amr Elsayed Mohammed Abdallah ◽  
Ehab Fathy El-Salakawy
Keyword(s):  
Aspect Ratio ◽  
Axial Load ◽  
Load Capacity ◽  
Load Level ◽  
Experimental Results ◽  
Rc Columns ◽  
Drift Capacity ◽  
Glass Fiber Reinforced ◽  
Axial Load Capacity ◽  
Code Provisions

The mechanical and physical properties of glass fiber-reinforced polymer (GFRP) reinforcement are different from steel, which requires independent code provisions for GFRP-reinforced concrete (RC) members. The currently available code provisions for GFRP-RC members still need more research evidence to be inclusive. For example, the available provisions for confinement reinforcement of FRP-RC columns do not consider the effects of column aspect ratio, which is not yet supported by any available research data. In this study, two full-scale spirally reinforced GFRP-RC circular columns were constructed and tested under concurrent seismic and axial loads. Both specimens had an aspect ratio (shear span-to-diameter ratio) of 7.0, while other two specimens with an aspect ratio of 5.0, from a previous stage of this study, were included for comparison purposes. For each aspect ratio, each specimen was loaded under one of two levels of axial load; 20 or 30% of the axial load capacity of the column section. All test specimens had a 35 MPa concrete compressive strength, 350-mm diameter, 85-mm spiral pitch and 1.2% longitudinal reinforcement ratio. The experimental results were analyzed in terms of hysteretic response, drift capacity and inelastic deformability hinge length. Based on the experimental results, it can be concluded that the aspect ratio affects the magnitude of secondary moments and inelastic deformability hinge length. In addition, the aspect ratio may affect drift capacity of GFRP-RC columns, depending on axial load level.

Experimental Investigation on Rehabilitation of Corroded RC Columns with BSP and HPFL under Combined Loadings

2020 ◽  
Vol 146 (8) ◽  
pp. 04020157 ◽  
Author(s):  
Hua Huang ◽  
Min Huang ◽  
Wei Zhang ◽  
Stanislav Pospisil ◽  
Tao Wu
Keyword(s):  
Experimental Investigation ◽  
Rc Columns ◽  
Combined Loadings

Short reinforced concrete column capacity under biaxial bending and axial load

2000 ◽  
Vol 27 (6) ◽  
pp. 1173-1182 ◽  
Author(s):  
H P Hong
Keyword(s):  
Reinforced Concrete ◽  
Probabilistic Analysis ◽  
Axial Load ◽  
Failure Surface ◽  
Biaxial Bending ◽  
Reinforced Concrete Column ◽  
Rc Columns ◽  
Nonlinear Stress ◽  
Modeling Errors ◽  
Error Optimization

The paper describes the development of a simple theoretical approach in estimating the capacity of short reinforced concrete (RC) columns under biaxial bending and axial load. The developed approach considers the nonlinear stress-strain relations of concrete and reinforcing steel and does not make the assumption about the limiting strain of extreme compression fiber of concrete. The solution is obtained using a nonlinearly constrained optimization algorithm. The approach was used to estimate the theoretical capacities of many tested RC columns found in the literature. A probabilistic analysis of the modeling errors was carried out using the ratios of the test-to-predicted results. The probabilistic analysis was extended to include two simplified theoretical methods: the reciprocal load method given by Bresler and the failure surface method given by Hsu.Key words: biaxial bending, modeling error, optimization, probability distribution.

Sign in / Sign up

Export Citation Format

Share Document