scholarly journals Micro-hardness and strain-rate-dependent compressive response of an ultra-light-weight Mg-Li-Al alloy

2022 ◽  
Vol 890 ◽  
pp. 161703
Author(s):  
Haoyang Li ◽  
Chenwei Shao ◽  
David Funes Rojas ◽  
Mauricio Ponga ◽  
James D. Hogan
Keyword(s):  
Strain Rate ◽  
Al Alloy ◽  
Light Weight ◽  
Micro Hardness ◽  
Compressive Response ◽  
Rate Dependent

A Study of Strain and Strain-Rate Dependent Properties of a Superplastic Zn-Al Alloy Under Biaxial Stresses

1982 ◽  
Vol 104 (1) ◽  
pp. 41-46
Author(s):  
T. C. Hsu ◽  
I. M. Bidhendi
Keyword(s):  
Strain Rate ◽  
Stress Ratio ◽  
Local Stress ◽  
Biaxial Stress ◽  
Al Alloy ◽  
Local Geometry ◽  
Forming Process ◽  
Rate Dependent ◽  
Strain And Strain Rate ◽  
Liquid Behavior

A superplastic Zn-Al alloy in sheet form is formed into a bulge over a circular hole by pneumatic pressure. The geometry, the stress, the strain, and the strain-rate are determined at various points covering the whole specimen and at various stages of the forming process. The complicated shape, and its complicated changes, are represented by introducing an index for the local geometry, called “prolateness,” which is also related to the local stress ratio in a simple way. The biaxial stress is analyzed into a strain-proportional and a strain-rate-proportional component, which represent, respectively, the quasi-solid and the quasi-liquid behavior of the superplastic material.

Quantitative Analysis of Instability for Superplastic Tension

2014 ◽  
Vol 941-944 ◽  
pp. 1505-1508
Author(s):  
Zhi Ping Guan ◽  
Ming Wen Ren ◽  
Pin Kui Ma ◽  
Po Zhao
Keyword(s):  
Strain Rate ◽  
Strain Path ◽  
Superplastic Forming ◽  
Uniform Strain ◽  
Deformation Condition ◽  
Al Alloy ◽  
Uniform Deformation ◽  
Rate Dependent ◽  
Strain And Strain Rate

In conventional analysis of instability, a rough prediction of uniform deformation was obtained due to taking material parameters as constants. In this study, the constitutive equation with varying parameters for Zn-5%Al alloy at 340 °C is employed to predict the critical values of uniform strain in tension based on Considere criterion and Hart criterion, respectively. It should address the factor of strain rate in the characterization of the capability of uniform deformation on superplastic alloys, or for that matter, on any rate-dependent material. Comparison and analysis indicated that the results on Hart criterion have the better predictability of uniform deformation than Considere criterion. The Considere criterion is dependent on strain path, while Hart crtierion is merely dependent on the values of strain and strain rate in tension, and is independent on the strain path or the deformation condition or the deformation history. Therefore, the uniform strain vs. strain rate relation can be taken as a quantitative reference for designing a reasonable strain path during superplastic forming with increase of formability and reduction of forming time.

The high strain rate compressive response of Mg-Al alloy/fly Ash cenosphere composites

JOM ◽  
2011 ◽  
Vol 63 (2) ◽  
pp. 48-52 ◽  
Author(s):  
Dung D. Luong ◽  
Nikhil Gupta ◽  
Pradeep K. Rohatgi
Keyword(s):  
Fly Ash ◽  
High Strain Rate ◽  
Strain Rate ◽  
High Strain ◽  
Al Alloy ◽  
Compressive Response ◽  
Fly Ash Cenosphere

Strain-rate dependent material properties of selective laser melted AlSi10Mg and AlSi3.5Mg2.5

2020 ◽  
Vol 62 (6) ◽  
pp. 573-583
Author(s):  
Andreas Lutz ◽  
Lukas Huber ◽  
Claus Emmelmann
Keyword(s):  
Strain Rate ◽  
Material Properties ◽  
Rate Dependent

Strain-Rate Dependent Deformation Behavior in WC-10 wt%Ni 3Al Cermet Micropillars Under Uniaxial Compression

2019 ◽  
Author(s):  
Minai Zhang ◽  
Xin Wang ◽  
Alexander D. Dupuy ◽  
Julie M. Schoenung ◽  
Xiaoqiang Li
Keyword(s):  
Strain Rate ◽  
Uniaxial Compression ◽  
Deformation Behavior ◽  
Rate Dependent

scholarly journals Identification of the LLDPE Constitutive Material Model for Energy Absorption in Impact Applications

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1537
Author(s):  
Luděk Hynčík ◽  
Petra Kochová ◽  
Jan Špička ◽  
Tomasz Bońkowski ◽  
Robert Cimrman ◽  
...  
Keyword(s):  
Strain Rate ◽  
Material Model ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Linear Low Density Polyethylene ◽  
Stress Strain ◽  
Rate Dependent ◽  
Constitutive Material Model ◽  
Principal Directions ◽  
Constitutive Material

Current industrial trends bring new challenges in energy absorbing systems. Polymer materials as the traditional packaging materials seem to be promising due to their low weight, structure, and production price. Based on the review, the linear low-density polyethylene (LLDPE) material was identified as the most promising material for absorbing impact energy. The current paper addresses the identification of the material parameters and the development of a constitutive material model to be used in future designs by virtual prototyping. The paper deals with the experimental measurement of the stress-strain relations of linear low-density polyethylene under static and dynamic loading. The quasi-static measurement was realized in two perpendicular principal directions and was supplemented by a test measurement in the 45° direction, i.e., exactly between the principal directions. The quasi-static stress-strain curves were analyzed as an initial step for dynamic strain rate-dependent material behavior. The dynamic response was tested in a drop tower using a spherical impactor hitting a flat material multi-layered specimen at two different energy levels. The strain rate-dependent material model was identified by optimizing the static material response obtained in the dynamic experiments. The material model was validated by the virtual reconstruction of the experiments and by comparing the numerical results to the experimental ones.

Sign in / Sign up

Export Citation Format

Share Document