Effect of Sc on solidification segregation and subsequent friction stir processing of aluminium alloy

2020 ◽  
Author(s):  
P.K. Mandal
Keyword(s):  
Aluminium Alloy ◽  
Friction Stir Processing ◽  
Friction Stir

scholarly journals Surface Hardening of Aluminium Alloy with Addition of Zinc Particles by Friction Stir Processing

2020 ◽  
Vol 10 (1) ◽  
pp. 408-414
Author(s):  
Nurul Muhayat ◽  
Alvian Restu Putra Utama ◽  
Keyword(s):  
Mechanical Alloying ◽  
Physical Properties ◽  
Aluminium Alloy ◽  
Friction Stir Processing ◽  
Surface Hardening ◽  
Alloy Plate ◽  
Friction Stir ◽  
Material Hardness ◽  
Mechanical And Physical Properties ◽  
Uppermost Layer

AbstractMechanical alloying can be carried out by a method known as friction stir processing, whereby solid Zn particles in a solution are distributed onto an aluminium alloy plate. The aim of this study was to determine the effects of a volume of Zn particles on the mechanical and physical properties of aluminium 1xxx alloy that had been subjected to friction stir processing. The specimens were plates composed of 1xxx series aluminium. A groove, measuring 12 mm in diameter, was pierced to various depths, and the Zn particles in these containers were then subjected to friction stir processing using a pin-less tool with a diameter of 15 mm. The results showed that the highest hardness was found in the uppermost layer of the workpiece, and this gradually decreased with thickness. An increase in the amount of Zn particles caused an increase in material hardness. The highest hardness of 87.1 HV in the friction stir-processed AA1100 was obtained at the highest volume of Zn compared to the hardness of 44.5 HV, which was obtained for the specimen without the addition of Zn.

scholarly journals Friction Stir Processing of SSM356 Aluminium Alloy

2014 ◽  
Vol 97 ◽  
pp. 732-740 ◽  
Author(s):  
S. Chainarong ◽  
P. Muangjunburee ◽  
S. Suthummanon
Keyword(s):  
Aluminium Alloy ◽  
Friction Stir Processing ◽  
Friction Stir

scholarly journals Effect of Friction Stir Processing on Gas Tungsten Arc-Welded and Friction Stir-Welded 5083-H111 Aluminium Alloy Joints

2019 ◽  
Vol 2019 ◽  
pp. 1-14 ◽  
Author(s):  
Sipokazi Mabuwa ◽  
Velaphi Msomi
Keyword(s):  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Aluminium Alloy ◽  
Friction Stir Processing ◽  
Welded Joints ◽  
Ultrafine Grain ◽  
Dimple Size ◽  
Friction Stir ◽  
Gas Tungsten Arc ◽  
Gas Tungsten

This paper presents the analysis of the friction stir-processed aluminium alloy 5083-H111 gas tungsten arc-welded and friction stir-welded joints. The comparative analysis was performed on the processed and unprocessed gas tungsten arc-welded and friction stir-welded joints of similar aluminium alloy 5083-H111. The results showed a clear distinction between the friction stir processed joints and unprocessed joints. There is a good correlation observed between the microstructural results and the tensile results. Ultrafine grain sizes of 4.62 μm and 7.177 μm were observed on the microstructure of the friction stir-processed friction stir-welded and gas tungsten arc-welded joints. The ultimate tensile strength for friction stir-welded and gas tungsten arc-welded before friction stir processing was 153.75 and 262.083 MPa, respectively. The ultimate tensile strength for friction stir processed friction stir-welded joint was 303.153 MPa and gas tungsten arc-welded joints one was 249.917 MPa. The microhardness values for the unprocessed friction stir-welded and gas tungsten arc-welded joints were both approximately 87 HV, while those of the friction stir-processed ones were 86.5 and 86 HV, respectively. The application of friction stir processing transformed the gas tungsten arc morphology from brittle to ductile dimples and reduced the ductile dimple size of the unprocessed friction stir-welded joints from the range of 4.90–38.33 μm to 3.35–15.59 μm.

Fatigue life improvement by friction stir processing of 5083 aluminium alloy MIG butt welds

2014 ◽  
Vol 70 ◽  
pp. 68-74 ◽  
Author(s):  
L.P. Borrego ◽  
J.D. Costa ◽  
J.S. Jesus ◽  
A.R. Loureiro ◽  
J.M. Ferreira
Keyword(s):  
Fatigue Life ◽  
Aluminium Alloy ◽  
Friction Stir Processing ◽  
Butt Welds ◽  
Friction Stir ◽  
Life Improvement

Effect of Process Parameters on Defect Formation in Friction Stir Processed 6082-T6 Aluminium Alloy

2012 ◽  
Vol 232 ◽  
pp. 3-7
Author(s):  
Akinlabi Esther Titilayo ◽  
Akinlabi Stephen Akinwale
Keyword(s):  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Aluminium Alloy ◽  
Process Parameters ◽  
Friction Stir Processing ◽  
Feed Rate ◽  
Rotational Speed ◽  
Defect Formation ◽  
Processing Parameters ◽  
Friction Stir

This paper reports the effects of processing parameters on defects formed during friction stir processing of 6082-T6 Aluminium Alloy. The plates were processed by varying the feed rate between 50 and 250 mm/min, while the rotational speed was varied between 1500 and 3500 rpm to achieve the best result. It was observed that the sheets processed at the highest feed rate considered in this research resulted in wormhole defect. These processed samples with defects were correlated to the tensile results and it was found that the Ultimate Tensile Strength (UTS) of these samples was relatively low compared to other samples without defects.

Sign in / Sign up

Export Citation Format

Share Document