scholarly journals Application of geosynthetic inclusions in cohesion less soil reinforcement

2021 ◽  
Author(s):  
Shwetha Prasanna
Keyword(s):  
Soil Reinforcement ◽  
Cohesion Less Soil

scholarly journals Stabilization of Slopes of Sandy Soils by Using Geosynthetics

2021 ◽  
Vol 1197 (1) ◽  
pp. 012081
Author(s):  
Tudumu Viveka ◽  
Namburu Sandeep Kumar ◽  
K. Shyam Chamberlin
Keyword(s):  
Slope Failure ◽  
Load Transfer ◽  
Load Resistance ◽  
Internal Resistance ◽  
Soil Reinforcement ◽  
Cohesionless Soils ◽  
Angle Of Internal Friction ◽  
Lateral Load Resistance ◽  
Shear Box ◽  
Cohesion Less Soil

Abstract This paper intended on the interactive performance of geo-synthetics in slope stabilization of non-cohesive soils. Presently, geo-synthetics are performing crucial role in geo-technical uses for reinforcing of soils for slope of stabilization, soil reinforcement for foundations, R E walls for highway and flyover construction etc. Usually, cohesion less soil is ideal for backfills of the embankments as of its exceptional drainage properties, at a low-level hydrostatic pressure built-up on slopes and excessive internal resistance owing to friction and interlocking. To research this property of geo-synthetics, relative density and shear box tests are done on the soil by varying geosynthetics for assessment of the shear parameters of sample. The mosquito reinforcement net as reinforcement on cohesionless soils, improvement in the angle of internal friction of the soil was observed by twenty-two percentage that the shear strength to be improved by 26.5%. So, the soil’s lateral load resistance or load transfer capacity improved to prevent the slope failure thereby saves the entire structure.

scholarly journals Foundation Piles—A New Feature for Concrete 3D Printers

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2545
Author(s):  
Marcin Hoffmann ◽  
Krzysztof Żarkiewicz ◽  
Adam Zieliński ◽  
Szymon Skibicki ◽  
Łukasz Marchewka
Keyword(s):  
3D Printing ◽  
Rapid Development ◽  
Construction Materials ◽  
Shallow Foundation ◽  
Soil Reinforcement ◽  
3D Printer ◽  
Permanent Formwork ◽  
3D Printers ◽  
New Feature ◽  
The Cost

Foundation piles that are made by concrete 3D printers constitute a new alternative way of founding buildings constructed using incremental technology. We are currently observing very rapid development of incremental technology for the construction industry. The systems that are used for 3D printing with the application of construction materials make it possible to form permanent formwork for strip foundations, construct load-bearing walls and partition walls, and prefabricate elements, such as stairs, lintels, and ceilings. 3D printing systems do not offer soil reinforcement by making piles. The paper presents the possibility of making concrete foundation piles in laboratory conditions using a concrete 3D printer. The paper shows the tools and procedure for pile pumping. An experiment for measuring pile bearing capacity is described and an example of a pile deployment model under a foundation is described. The results of the tests and analytical calculations have shown that the displacement piles demonstrate less settlement when compared to the analysed shallow foundation. The authors indicate that it is possible to replace the shallow foundation with a series of piles combined with a printed wall without locally widening it. This type of foundation can be used for the foundation of low-rise buildings, such as detached houses. Estimated calculations have shown that the possibility of making foundation piles by a 3D printer will reduce the cost of making foundations by shortening the time of execution of works and reducing the consumption of construction materials.

Instrumented Full Scale Test and Numerical Analysis to Investigate Performance of Bamboo Pile-Mattress System as Soil Reinforcement for Coastal Embankment on Soft Clay

2014 ◽  
Vol 501-504 ◽  
pp. 2132-2137
Keyword(s):  
Numerical Analysis ◽  
Geotechnical Engineering ◽  
Soft Clay ◽  
Full Scale ◽  
Soil Reinforcement ◽  
Disaster Mitigation ◽  
Full Scale Test ◽  
Scale Test

Removed due to plagiarism. The original was published by: Liu, Deng and Chu (eds) © 2008 Science Press Beijing and Springer-Verlag GmbH Berlin Heidelberg Geotechnical Engineering for Disaster Mitigation and Rehabilitation http://www.ftsl.itb.ac.id/kk/geotechnical_engineering/wp-content/uploads/2008/06/irsyam-165.pdf

Research to build technological procedure for soft ground improvement using sea sand-cement-fly ash column

2020 ◽  
Vol 61 (HTCS6) ◽  
pp. 1-9
Author(s):  
Thinh Duc Ta ◽  
Phuc Dinh Hoang ◽  
Thang Anh Bui ◽  
Trang Huong Thi Ngo ◽  
Diu Thi Nguyen ◽  
...  
Keyword(s):  
Fly Ash ◽  
Load Capacity ◽  
Ground Improvement ◽  
Soft Soil ◽  
Soil Reinforcement ◽  
Soft Ground ◽  
Design Calculation ◽  
Sea Sand ◽  
Composite Ground ◽  
Soft Ground Improvement

Sea sand-cement-fly ash column technology for soft soil treatment is a new technology in the process of completing the theoretical basis, the experimental basis, and the construction of the ground treatment technological procedure. The paper presents the results of scientific research on design, calculation, construction, and acceptance of sea sand-cement-fly ash column. The scientific basis for the design of column is to consider the role of the column in composite ground, that is to use the column as soft ground improvement or soft soil reinforcement. The important parameters for the column design are: cement and fly ash content; column length; column diameter; number of columns; distance among columns; load capacity and settlement of composite ground. The sequence of steps of construction and acceptance of column includes: selection of construction equipment, preparation of construction sites, trial construction, official construction, evaluation of ground quality after treatment and preparation of document for acceptance.

scholarly journals An Experimental Study of Horizontal Bearing Capacity of Vertical Steel Floral Tube Micropiles with Double Grouting

2018 ◽  
Vol 2018 ◽  
pp. 1-11
Author(s):  
Kaiyang Wang ◽  
Yanjun Shang
Keyword(s):  
Bearing Capacity ◽  
Large Scale ◽  
Slip Surface ◽  
Bending Moment ◽  
Shear Capacity ◽  
Soil Reinforcement ◽  
Scale Model ◽  
Soil Pressure ◽  
Floral Tube ◽  
Grouting Pressure

This paper examines the performance of a novel technology, vertical steel floral tube micropiles with double grouting. It is the combination of micropile technology and double grouting technology. A large-scale model tank was applied to impart horizontal bearing capacity, and the slope soil pressure and flexural performance of the micropile were investigated under four experimental conditions. The peak grouting pressure during the double grouting process was defined as the fracturing pressure of the double grouting, and it was positively correlated to the interval time between first grouting and secondary grouting. Compared with traditional grouting, double grouting increased the horizontal bearing capacity of the single micropile with the vertical steel floral tube by 24.42%. The horizontal bearing capacity was also 20.25% higher for the structure with three micropiles, compared with a 3-fold value of horizontal sliding resistance. In the test, the maximum bending moment acting on the pile above the sliding surface was located 2.0–2.5 m away from the pile top, and the largest negative bending moment acting on the pile below the slip surface was located 4.0 m away from the pile top. The ultimate bending moment of the single pile increased by 12.8 kN·m with double grouting, and the bending resistance increased by 96.2%. The experimental results showed that the double grouting technology significantly improved the horizontal bearing capacity of the micropile with the steel floral tube, and the soil reinforcement performance between piles was more pronounced. Also, the shear capacity and the flexural capacity were significantly improved compared with the original technology.

Sign in / Sign up

Export Citation Format

Share Document