Microstructure evolution of alloy 625 foil and sheet during creep at 750°C

2008 ◽  
Vol 498 (1-2) ◽  
pp. 412-420 ◽  
Author(s):  
Neal D. Evans ◽  
Philip J. Maziasz ◽  
John P. Shingledecker ◽  
Yukinori Yamamoto
Keyword(s):  
Microstructure Evolution ◽  
Alloy 625

Microstructure evolution for isothermal sintering of binder jet 3D printed alloy 625 above and below the solidus temperature

2021 ◽  
pp. 102276
Author(s):  
Chuyuan Zheng ◽  
Amir Mostafaei ◽  
Pierangeli Rodriguez de Vecchis ◽  
Ian Nettleship ◽  
Markus Chmielus
Keyword(s):  
Microstructure Evolution ◽  
Solidus Temperature ◽  
Alloy 625 ◽  
3D Printed

Microstructure Evolution Induced by Ultraviolet Light Irradiation in Ti-Si Codoped Diamond-like Carbon films

2014 ◽  
Vol 29 (9) ◽  
pp. 941
Author(s):  
JIANG Jin-Long ◽  
WANG Qiong ◽  
HUANG Hao ◽  
ZHANG Xia ◽  
WANG Yu-Bao ◽  
...  
Keyword(s):  
Ultraviolet Light ◽  
Microstructure Evolution ◽  
Carbon Films ◽  
Light Irradiation ◽  
Diamond Like Carbon ◽  
Ultraviolet Light Irradiation

INCONEL ALLOY 725

Alloy Digest ◽  
1994 ◽  
Vol 43 (1) ◽  
Keyword(s):  
Fracture Toughness ◽  
Corrosion Resistance ◽  
Shear Strength ◽  
Physical Properties ◽  
Tensile Properties ◽  
High Strength ◽  
Heat Treating ◽  
Inconel Alloy ◽  
Alloy 625

Abstract INCONEL ALLOY 725 is an age-hardenable alloy that displays high strength along with excellent ductility and toughness. Its corrosion resistance is comparable to alloy 625. Good flattening properties are exhibited in age-hardened tubing. This datasheet provides information on composition, physical properties, hardness, tensile properties, and shear strength as well as fracture toughness. It also includes information on corrosion resistance as well as heat treating and machining. Filing Code: Ni-445. Producer or source: Inco Alloys International Inc.

INCONEL ALLOY 625 LCF

Alloy Digest ◽  
1992 ◽  
Vol 41 (11) ◽  
Keyword(s):  
Corrosion Resistance ◽  
High Temperature ◽  
Physical Properties ◽  
Tensile Properties ◽  
Thermal Fatigue ◽  
Inconel Alloy ◽  
Alloy 625 ◽  
Temperature Performance

Abstract INCONEL Alloy 625LCF is a special alloyed, melted, and processed version of INCONEL alloy 625 (Alloy Digest Ni-121, February 1967) to optimize low-cycle and thermal fatigue up to 1200 deg F (650 deg C). This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fatigue. It also includes information on high temperature performance and corrosion resistance as well as forming and joining. Filing Code: Ni-416. Producer or source: Inco Alloys International Inc..

INCOCLAD 625/STEEL

Alloy Digest ◽  
2002 ◽  
Vol 51 (12) ◽  
Keyword(s):  
Corrosion Resistance ◽  
Alloy 625 ◽  
Clad Tube ◽  
Metallurgical Bond

Abstract INCOCLAD625/Steel is a bimetallic clad tube with alloy 625 (UNS N06625) on the outside and with a metallurgical bond holding the alloys together. This datasheet provides information on composition. It also includes information on corrosion resistance as well as forming and joining. Filing Code: Ni-597. Producer or source: Special Metals Corporation.

Surface Microstructure Evolution Upon Silicidation of Ni(Pt) and the Different Responses to Metal Etch

2013 ◽  
Author(s):  
Wentao Qin ◽  
Dorai Iyer ◽  
Jim Morgan ◽  
Carroll Casteel ◽  
Robert Watkins ◽  
...  
Keyword(s):  
Thin Film ◽  
Oxide Film ◽  
Microstructure Evolution ◽  
Depth Profiling ◽  
Surface Microstructure ◽  
The Difference ◽  
Surface Microstructures ◽  
Pt Films

Abstract Ni(5 at.%Pt ) films were silicided at a temperature below 400 °C and at 550 °C. The two silicidation temperatures had produced different responses to the subsequent metal etch. Catastrophic removal of the silicide was seen with the low silicidation temperature, while the desired etch selectivity was achieved with the high silicidation temperature. The surface microstructures developed were characterized with TEM and Auger depth profiling. The data correlate with both silicidation temperatures and ultimately the difference in the response to the metal etch. With the high silicidation temperature, there existed a thin Si-oxide film that was close to the surface and embedded with particles which contain metals. This thin film is expected to contribute significantly to the desired etch selectivity. The formation of this layer is interpreted thermodynamically.

Sign in / Sign up

Export Citation Format

Share Document